KitchenAid KCES556HBL, WCE55US0H, WCE55US4H, WCE55US6H, WCE77US0H Installation Guide

...

ELECTRIC COOKTOP

IMPOR

À conser

IMPOR

Ahorre para el uso del inspector eléctrico local.

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION DE LA TABLE

DECUISSON ÉLECTRIQUE

INSTRUCCIONES DE INSTALACIÓN DE

LAPARRILLA ELÉCTRICA

Table of Contents/Table des matières/Tabla de contenidos

COOKTOP SAFETY ........................................................................2

INSTALLATION REQUIREMENTS .................................................2

Tools and Parts .............................................................................2

Location Requirements ................................................................2

Electrical Requirements ...............................................................4

INSTALLATION INSTRUCTIONS ...................................................5

Prepare Cooktop for Installation ..................................................5

Install Cooktop .............................................................................5

Make Electrical Connection .........................................................7

Attach Cooktop to Countertop ....................................................9

Complete Installation ...................................................................9

SEGURIDAD DE LA PARRILLA ELÉCTRICA ..........................18

REQUISITOS DE INSTALACIÓN ..............................................18

Herramientas y piezas ................................................................18

Requisitos de ubicación .............................................................18

Requisitos eléctricos ................................................................... 20

INSTRUCCIONES DE INSTALACIÓN ......................................21

Preparación de la parrilla eléctrica para la instalación ............... 21

Instalación de la parrilla eléctrica ...............................................21

Haga la conexión del suministro eléctrico .................................. 23

Cómo jar la parrilla eléctrica almostrador ................................ 25

Completar la instalación .............................................................25

SÉCURITÉ DE LA TABLE DE CUISSON .....................................10

EXIGENCES D’INSTALLATION ...................................................10

Outils et pièces ...........................................................................10

Exigences d’emplacement .........................................................10

Spécications électriques ..........................................................12

INSTRUCTIONS D’INSTALLATION .............................................13

Préparation de la table de cuisson pour l’installation ................13

Installation de la table de cuisson ..............................................13

Raccordement électrique ...........................................................15

Fixation de la table de cuisson au plan detravail......................17

Achever l’installation ..................................................................17

TANT:

ve for local electrical inspector's use.

TANT :

ver pour consultation par l'inspecteur local des installations électriques.

TANT :

W11206696B

COOKTOP SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

follow instructions.

You

can be killed or seriously injured if you don't

instructions.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

■ Tape measure

■

/4" (6.35 mm) nut driver

Parts supplied

■ Foam strip roll

■ Clamping brackets (2)

Parts needed

■ A UL listed or CSA approved connector for ½" (1.3 cm)

diameter conduit

■ UL listed wire connectors

Check local codes. Check existing electrical supply. See the “Electrical Requirements” section.

It is recommended that all electrical connections be made by a licensed, qualied electrical installer.

■ Marker or pencil

■ Pliers

■ Flat-blade screwdriver

■ 2½" (6.4 cm) clamping

■ Screws (2)

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

When installing cooktop, use minimum dimensions given.

■ To eliminate the risk of burns or re by reaching over the

heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5” (12.7 cm) beyond the bottom of the cabinets.

■ The cooktop must be a specied cooktop that is approved

to be installed either alone or over an undercounter built-in oven. Check the cooktop base for an approved installation label. If you do not nd this label, contact your dealer to conrm that your cooktop is approved.

■ The cooktop must be installed in a level countertop.

■ Ovens approved for this type of installation will have an

approval label located on the top of the oven. If you do not nd this label, contact your dealer to conrm that your oven is approved. Refer to oven manufacturer’s Installation Instructions for approval for built-in undercounter use and proper cutout dimensions.

■ The cooktop should be installed away from strong draft

areas, such as windows, doors, fans or strong heating vents. The cooktop should be located for convenient use in the kitchen.

■ Use the countertop opening dimensions that are given

with these Installation Instructions. Given dimensions are minimum clearances and provide 0" (0 cm) clearance.

■ Grounded electrical supply is required. See “Electrical

Requirements” section.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate, or sustain other damage.

Product Dimensions

Cabinet Dimensions

IMPORTANT: If installing a range hood or microwave hood

combination above cooking surface, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface.

A. Glass depth - black and white models - 21 ³⁄4" (55.2 cm)

Glass depth - stainless steel models - 22 ¹⁄8" (56.4 cm)

B. Glass width - 24" (60.9 cm) models - 23

Glass width - 30" (76.2 cm) models - 30 13/16" (78.4 cm)

Glass width - 36" (91.4 cm) models - 36 5/16" (92.3 cm) C. Frame depth - 20 D. Frame width - 24" (60.9 cm) models - 21

Frame width - 30" (76.2 cm) models - 29" (73.7 cm)

Frame width - 36" (91.4 cm) models - 34 7/16" (87.5 cm) E. Cooktop height with bottom heat shield - 3 Cooktop height lighted knobs - 4 F. Cooktop height including conduit (located at rear of cooktop, right

side) - 5" (12.7 cm) Cooktop height lighted knobs, including conduit (located at rear of

cooktop, right side) - 6

⁄16" (51.6 cm)

/16" (15.4 cm)

/16" (60.5 cm)

/64" (55.7 cm)

/16 (12.55 cm)

⁄8" (9.8 cm)

A. 24" (60.9 cm) on 24" models; 30" (76.2 cm) on 30" models;

36" (91.4 cm) on 36" models B. Combustible area above countertop (shown by dashed box above) C. 30" (76.2 cm) minimum clearance between top of cooktop

platform and bottom of uncovered wood or metal cabinet

(24" [61 cm] minimum clearance if bottom of wood or metal

cabinet is covered by not less than ¹⁄

millboard covered with not less than No. 28 MSG sheet steel,

0.015" [0.04 cm] stainless steel, or 0.024” [0.06 cm] aluminum

or0.020" [0.05 cm] copper) D. 13" (33 cm) recommended upper cabinet depth E. 2" (5.1 cm)

F. 20¹⁄

" (52.0 cm) recommended cutout.

Will ﬁt in cutout from 20³⁄8"-209⁄16" (51.8-52.2 cm). G. 18" (45.7 cm) minimum clearance from upper cabinet to

countertop within minimum horizontal clearances to cooktop H. Junction box or outlet: 7" (17.8 cm) minimum from top of

countertop I. Junction box or outlet: 9" (23.0 cm) maximum from right side

ofcabinet

J. 29¹⁄

" (74.9 cm) recommended cutout on 30" (76.2 cm) models. Will ﬁt in cutout from 29 ¹⁄16"-29 9⁄16" (73.8-75.1 cm) on 30" (76.2cm) models. 35¹⁄2" (90.2 cm) recommended cutout on 36" (91.4 cm) models. Will ﬁt in cutout from 34 9⁄16"-35 9⁄16" (87.8-90.3 cm) on 36"(91.4cm) models. 22 5/16" (56.67 cm) recommended cutout on 24" (61.0 cm) Will ﬁt in cutout from 22 1/4 - 22 3/7 (56.4 - 57.0 cm) on 24 (61.0 cm) models.

K. 2

/2" (6.35 cm) minimum distance to nearest left and right side

combustible surface above cooktop

L. 1

/2" (3.81 cm) minimum clearance between back wall and

countertop

"[0.6 cm] ﬂame retardant

NOTES: After making the countertop cutout, some installations may require notching down the base cabinet side walls to clear

A. Location of Power Cord (length of power cord is

48" (121.9 cm), including the conduit)

the cooktop base. To avoid this modication, use a base cabinet with sidewalls wider than the cutout.

If cabinet has a drawer, a 5¹⁄

" (14.0 cm) depth clearance from the top of the countertop to the top of the drawer (or other obstruction) in base cabinet is required.

Electrical Requirements

WARNING

■ The cooktop is rated for 120/208 V or 120/240 V. Some

models have a neutral (white) wire.

For power requirements, refer to the following table:

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge copper wire.

Electrically ground cooktop.

Failure to follow these instructions can result in death, fire, or electrical shock.

If codes permit and a separate ground wire is used, it is recommended that a qualied electrical installer determine that the ground path and wire gauge are in accordance with local codes.

Check with a qualied electrical installer if you are not sure the cooktop is properly grounded.

Make sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91-latest edition, and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

Before You Make the Electrical Connection:

To properly install your cooktop, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

Use a 3-wire or 4-wire, single phase, 120/208 V or 120/240 V, 60 Hz, AC only. The model/serial number rating plate is located on the metal cabinet underneath the cooktop. See the following illustration.

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

A. Model/serial number plate

Family Model Number

WCE55US0H 5.0 kW 6.7 kW WCE55US4H 5.0 kW 6.7 kW WCE55US6H 6.0 kW 8.0 kW WCE77US0H 6.4 kW 8.5 kW WCE77US6H 6.4 kW 8.5 kW WCE97US0H 6.8 kW 9.1 kW WCE97US6H 6.8 kW 9.1 kW MEC8830H 6.5 kW 8.6 kW MEC8836H 7.4 kW 9.9 kW KCES550H 7.9 kW 10.5 kW KCES556H 7.9 kW 10.5 kW KCES950H 7.2 kW 9.6 kW KCES956H 7.2 kW 9.6 kW JEC3430H 6.4 kW 8.5 kW JEC3536H 7.9 kW 10.5 kW JEC4424H 5.5kW 7.3 kW JEC4430H 7.2 kW 9.6 kW JEC4536H 7.2 kW 9.6 kW

■ The cooktop should be connected directly to the junction

box through exible, armored or nonmetallic sheathed, copper cable. The exible, armored cable extending from the fuse box or circuit breaker box should be connected directly to the junction box.

■ Locate the junction box to allow as much slack as possible

between the junction box and the cooktop so that the cooktop can be moved if servicing becomes necessary in the future.

■ Do not cut the conduit. Use the length of conduit provided.

A UL listed or CSA approved conduit connector must be provided at each end of the power supply cable (at the cooktop and at the junction box). A listed conduit connector is already provided at the cooktop.

■ If the house has aluminum wiring follow the procedure

below: Connect the aluminum wiring using special connectors

and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer’s recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

Electrical Ratings at 60 Hz 208 V~ 240 V~

INSTALLATION INSTRUCTIONS

LEFT SIDE

Prepare Cooktop for Installation

WARNING

Excessive Weight Hazard

Use two or more people to move and install cooktop.

Failure to do so can result in back or other injury.

Decide on the nal location for the cooktop. Avoid drilling into or severing existing wiring during installation.

1. Using 2 or more people, place the cooktop upside down

on a covered surface using the foam end posts from the packaging. Make sure that the knobs are not resting on the foam.

2. Remove foam strip roll from the package containing

literature. The roll contains four ¼" (0.64 cm) strips of foam. Remove one strip at a time. Apply the foam strip adhesive around bottom of the four edges of the cooktop glass, following the edges of the glass.

NOTE: The foam strip helps avoid damage to the underside of the cooktop glass from debris and helps the cooktop sit at on uneven counters.

Install Cooktop

Style 1: Cooktop over undercounter built-in oven IMPORTANT: Clamping brackets should not be used.

1. Using 2 or more people, place cooktop right side up into

thecutout. NOTE: Make sure that the front edge of the cooktop is

parallel to the front edge of the countertop. If repositioning is needed, lift entire cooktop up from cutout to avoid scratching the countertop.

Style 2: Cooktop over cabinets

1. Determine whether your cabinet construction provides

clearance for installing clamping brackets at cooktop baseends.

24" (60.9 cm), 30" (76.2 cm) and 36" (91.4 cm) traditional models

A. Cooktop base bottom B. Attachment screw C. Clamping bracket

A. Cooktop base B. ¼" (0.64 cm) Foam strip C. Cooktop

NOTE: For some models with trim on the front glass edge, apply the foam strip side down around bottom of the cooktop glass only on LEFT, RIGHT and BACK SIDE.

RIGHT SIDE

BACK SIDE

2. The clamping brackets can be installed before or after the

cooktop is placed into the cutout. Complete the following steps for the option you choose.

Installing Brackets Before Placing Cooktop in Cutout

Installing Brackets After Placing Cooktop in Cutout

1. Using 2 or more people, place the cooktop upside down

on a covered surface using the foam end posts from the packaging. Make sure that the knobs are not resting on the foam.

2. Remove the attachment screws for the bracket locations

from the bottom of the cooktop base.

3. Select bracket mounting holes that will allow the bracket to

extend far enough out from the cooktop for the installation of

" (6.4 cm) clamping screws. See the “Attach Cooktop to

2¹⁄ Countertop” section for illustration of clamping screw installation.

A. Edge of cooktop base bottom B. Clamping bracket C. Bracket mounting holes D. Bracket clamping hole E. Attachment screw

4. Attach brackets to cooktop base bottom with bracket

attachment screws using the bracket mounting holes selected in Step 3.

5. Rotate brackets so they do not extend beyond edge of

cooktop base.

6. Tighten attachment screws enough to hold brackets in place

when cooktop is placed in cutout.

7. Using 2 or more people, turn the cooktop right side up and

place in cutout. NOTE: Make sure that the front edge of the cooktop is

parallel to the front edge of the countertop. If repositioning is needed, lift entire cooktop up from cutout to avoid scratching the countertop.

8. Loosen the screws and rotate the brackets so that they are

perpendicular to the edge of the cooktop base and extend beyond its edge. Securely tighten screws.

1. Using 2 or more people, place cooktop right side up into the

cutout. NOTE: Make sure that the front edge of the cooktop is

parallel to the front edge of the countertop. If repositioning is needed, lift entire cooktop up from cutout to avoid scratching the countertop.

2. Remove the attachment screws for the selected bracket

locations from the bottom of the cooktop base.

3. Select bracket mounting holes that will allow the bracket to

extend far enough out from the cooktop for the installation

" (6.4 cm) clamping screws.

of2¹⁄

A. Cooktop B. Cooktop base C. Attachment screw D. Clamping bracket (extends far enough beyond cooktop

base to allow installation of clamping screws)

E. 2¹⁄

" (6.4 cm) clamping screw (to be installed in “Attach

Cooktop to Countertop”)

F. Countertop

4. Attach brackets to cooktop base bottom with bracket

attachment screws using the bracket mounting holes selected in Step 3. Securely tighten screws.

Make Electrical Connection

(12,7 cm)

(8.9 cm)

(12,7 cm)

(8.9 cm)

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge copper wire.

Electrically ground cooktop.

Failure to follow these instructions can result in death, fire, or electrical shock.

This cooktop is manufactured with a frame connected, green or bare ground wire. Connect the cooktop cable to the junction box through the UL listed or CSA approved conduit connector.

Electrical Connection Options

For cooktops with a 4-wire cable If your home has: And you will be

connecting to:

4-wire direct A fused disconnect

or circuit breaker box

3-wire direct A fused disconnect

or circuit breaker box

3¹⁄₂"

For cooktops with a 3-wire cable: If your home has: And you will be

connecting to:

4-wire direct A fused disconnect

or circuit breaker box

Go to Section:

4-Wire Cable from Power Supply to 4-Wire Cable from Cooktop

3-Wire Cable from Power Supply to 4-Wire Cable from Cooktop

Go to Section:

4-Wire Cable from Power Supply to 3-Wire Cable from Cooktop

4-Wire Cable from Power Supply to 4-Wire Cable from Cooktop

IMPORTANT: Use the 4-wire cable from power supply where

local codes do not permit connecting the frame-ground conductor to the neutral (white) junction box wire.

A. 4-wire cable from power supply B. Black wires C. Bare or green wires D. 4-wire cable from cooktop E. Junction box

1. Disconnect power.

2. Remove junction box cover, if present.

3. Connect the exible cable conduit from the cooktop to the

junction box using a UL listed or CSA approved connector for ½” (1.3 cm) conduit.

4. Tighten screws on conduit connector if present.

5. Connect the two black wires together using the UL listed

wire connectors.

6. Connect the two red wires together using the UL listed wire

connectors.

7. Connect the two white wires together using the UL listed

wire connectors.

8. Connect the green or bare ground wire from the cooktop

cable to the green or bare ground wire (in the junction box) using the UL listed wire connectors.

9. Install junction box cover.

10. Reconnect power.

F. White wires G. UL listed wire connector H. Red wires I. UL listed or CSA approved

conduit connector

3-wire direct A fused disconnect

or circuit breaker box

3¹⁄₂"

3-Wire Cable from Power Supply to 3-Wire Cable from Cooktop

3-Wire Cable from Power Supply to 4-Wire Cable

C D

from Cooktop

4-Wire Cable from Power Supply to 3-Wire Cable from Cooktop

IMPORTANT: Use the 3-wire cable from power supply where

local codes permit connecting the frame-ground conductor to the neutral (white) junction box wire:

A. 3-wire cable from power supply B. Red wires C. White and green or bare ground

wires (from cooktop) D. 4-wire cable from cooktop E. Junction box

F. White wire (from power supply) G. UL listed wire connector H. Black wires I. UL listed or CSA approved

conduit connector

1. Disconnect power.

2. Remove junction box cover, if present.

3. Connect the exible, cable conduit from the cooktop to

the junction box using UL listed or CSA approved conduit connector.

4. Tighten screws on conduit connector if present.

5. Connect the two black wires together using the UL listed

wire connectors.

6. Connect the two red wires together using the UL listed wire

connectors.

7. Connect the green or bare and white cooktop cable wires to

the white (neutral) wire in the junction box using the UL listed wire connectors.

8. Connect the green or bare ground wire from the cooktop

cable to the green or bare ground wire (in the junction box) using the UL listed wire connectors.

9. Install junction box cover.

10. Reconnect power.

IMPORTANT: Use the 4-wire cable from power supply where

local codes do not permit connecting the frame-ground conductor to the neutral (white) junction box wire:

A. 4-wire cable from power supply B. Red wires C. Green or bare ground wire

(from cooktop) D. 3-wire cable from cooktop E. Junction box

F. White wire (from power supply) G. UL listed wire connector H. Black wires I. UL listed or CSA approved

conduit connector

1. Disconnect power.

2. Remove junction box cover, if present.

3. Connect the exible cable conduit from the cooktop to the

junction box using a UL listed or CSA approved conduit connector.

4. Tighten screws on conduit connector if present.

5. Connect the two black wires together using the UL listed

wire connectors.

6. Connect the two red wires together using the UL listed wire

connectors.

7. Connect the green or bare ground wire from the cooktop

cable to the green or bare ground wire (in the junction box) using the UL listed wire connectors.

8. Put a UL listed wire connector on the end of the white wire. NOTE: Do not connect the bare ground wire to the neutral

(white) wire in the junction box.

9. Install junction box cover.

10. Reconnect power.

3-Wire Cable from Power Supply to 3-Wire Cable

from Cooktop

IMPORTANT: Use the 3-wire cable from power supply where

local codes permit connecting the frame-ground conductor to the neutral (white) junction box wire:

A. 3-wire cable from power supply B. Red wires C. Green or bare ground wire

(from cooktop)

D. 3-wire cable from cooktop

1. Disconnect power.

2. Remove junction box cover, if present.

3. Connect the exible cable conduit from the cooktop to the

junction box using a UL listed or CSA approved conduit connector.

4. Tighten screws on conduit connector if present.

5. Connect the two black wires together using the UL listed

wire connectors.

6. Connect the two red wires together using the UL listed wire

connectors.

7. Connect the green or bare cooktop cable wires to the white

(neutral) wire in the junction box using the UL listed wire connectors.

8. Install junction box cover.

9. Reconnect power.

E. Junction box F. White wire (from power supply) G. UL listed wire connector H. Black wires I. UL listed or CSA approved

conduit connector

Attach Cooktop to Countertop

NOTE: This section applies only if you are using clamping

brackets.

A. Glass cooktop B. Cooktop base C. Attachment screw D. Clamping bracket (extends far

enough beyond cooktop base to allow installation of clamping screws)

E. 2½" (6.4 cm) clamping screw F. Countertop G. Foam seal

1. Place the 2½" (6.4 cm) clamping screws into the outermost

hole in the clamping bracket.

2. Use a screwdriver to tighten the screws against the

countertop. Do not overtighten.

Complete Installation

1. Check that all parts are now installed. If there is an extra

part, go back through the steps to see which step was skipped.

2. Check that you have all your tools.

3. Dispose of/recycle all packaging materials.

4. Use a mild solution of liquid household cleaner and warm

water to clean cooktop before use. Dry thoroughly with a soft cloth. For more information, see the “Cooktop Care” section of the Use and Care Guide.

5. Read the “Cooktop Use” section in the cooktop Use and

Care Guide.

6. Reconnect power.

7. For further information about the product, read the User

Instructions.

NOTE: If the cooktop does not work after turning on the power, check that a circuit breaker has not tripped or a household fuse has not blown. See “Troubleshooting” section in the Use and Care Guide for further information.

If You Need Assistance or Service:

Please reference the “Assistance or Service” section of the Use and Care Guide or contact the dealer from whom you purchased your cooktop.

+ 19 hidden pages