KitchenAid KBZU242TSS00, KBZU122VSS00, KBZU122TSS00 Owner’s Manual

Kitchen_kid ®

OUTDOOR BUILT-IN DUAL SIDE BURNERS

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

In Canada, call for assistance, installation and service, call: 1-800-807-6777

or visit our website at www.kitchenaid.com

or visit our website at www.KitchenAid.ca

DEUX BRULEURS LATERAUX ENCASTRES

P

POUR USAGE EXTERIEUR

I" ° I" -..] . I I

Au Canada, pour assistance, installation ou service composez le 1-800-807-6777 ou visitez notre site web a...

www.KitchenAid.ca

Table of Contents/Table des matieres ............................................................................. 4

I I '=I %" " '-'i".ii "<.IBI'I'

iMPORTANT:

Save for local electrical inspector's use.
Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

iMPORTANT:

A conserver pour consultation par I'inspecteur local des installations 61ectriques.
Installateur : Remettre les instructions d'installation au propri6taire.
Propri6taire : Conserver les instructions d'installation pour r6f6rence ult6rieure.

Models/Modeles KBZU122VSS KBZU242VSS KBZU122TSS KBZU242TSS

W10176789A

OUTDOOR BUILT-IN SIDE BURNER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow
instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

_, DANGER

If you smell gas:

1. Shut off gas to the appliance.

_, WARNING

1. Do not store or use gasoline or other

flammable liquids or vapors in the
vicinity of this or any other appliance.

2. Extinguish any open flame.

2. An LP cylinder not connected for use

3. Open lid.

4. If odor continues, keep away from the

shall not be stored in the vicinity of

this or any other appliance.
appliance and immediately call your
gas supplier or your fire department.

State of California Proposition 65 Warnings:
WARNING: This product contains a chemical known to the State of California to cause cancer.

WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.

In the State of Massachusetts, the following installation instructions apply:
[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.
[] A flexible gas connector, when used, must not exceed 3 feet.

2

IMPORTANT: This side burner is manufactured for outdoor use only. For side burners that are to be used at elevations above

2000 ft (609.6 m) orifice conversion is required. See "Gas Supply Requirements" section. It is the responsibility of the installer to comply
with the minimum installation clearances specified on the model/serial rating plate. The model/serial rating plate can be found on the
right-hand side panel.

Copies of the standards listed may be obtained from:
National Fire Protection Association CSA International

One Batterymarch Park 8501 East Pleasant Valley Rd.
Quincy, Massachusetts 02269 Cleveland, Ohio 44131-5575

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electrical shock,

injury to persons, or damage when using the outdoor cooking

gas appliance, follow basic precautions, including the
following:

[] Do not install portable or built-in outdoor cooking gas

appliances in or on a recreational vehicle, portable trailer,
boat or in any other moving installation.

[] Always maintain minimum clearances from combustible

construction, see "Location Requirements" section.

[] The outdoor cooking gas appliance shall not be located

under overhead unprotected combustible construction.

[] This outdoor cooking gas appliance shall be used only

outdoors and shall not be used in a building, garage, or any
other enclosed area.

[] Keep any electrical supply cord and fuel supply hose away

from any heated surfaces.

[] Keep outdoor cooking gas appliance area clear and free

from combustible materials, gasoline and other flammable
vapors and liquids.

[] Do not obstruct the flow of combustion and ventilation air.

Keep the ventilation openings of the cylinder enclosure free
and clear from debris.

[] Inspect the gas cylinder supply hose before each use of the

outdoor cooking gas appliance. If the hose shows
excessive abrasion or wear, or is cut, it MUST be replaced

before using the outdoor cooking gas appliance. Contact
your dealer and use only replacement hoses specified for

use with the outdoor cooking gas appliance.

[] Visually check the burner flames. They should be blue.

Slight yellow tipping is normal for LP gas.

[] Check and clean burner/venturi tube for insects and insect

nest. A clogged tube can lead to fire under the outdoor
cooking gas appliance.

[] The LP gas supply cylinder to be used must be:

- constructed and marked in accordance with the
Specification for LP Gas Cylinders of the U.S. Department

of Transportation (DOT) or the National Standard of
Canada, CAN/CSA-B339, Cylinders, Spheres, and Tubes

for Transportation of Dangerous Goods; and Commission.

- provided with a listed overfilling prevention device.

- provided with a cylinder connection device compatible
with the connection for outdoor cooking gas appliances.

[] Always check connections for leaks each time you connect

and disconnect the LP gas supply cylinder. See

"Installation Instructions" section.

[] When the outdoor cooking gas appliance is not in use, the

gas must be turned off at the supply cylinder.

[] Storage of an outdoor cooking gas appliance indoors is

permissible only if the cylinder is disconnected and
removed from the outdoor cooking gas appliance.

[] Cylinders must be stored outdoors and out of the reach of

children and must not be stored in a building, garage, or

any other enclosed area.

[] The pressure regulator and hose assembly supplied with

the outdoor cooking gas appliance must be used. A

replacement pressure regulator and hose assembly

specific to your model is available from your outdoor
cooking gas appliance dealer.

[] Gas cylinder must include a collar to protect the cylinder

valve.

[] For appliances designed to use a CGA791 Connection:

Place a dust cap on cylinder valve outlet whenever the

cylinder is not in use. Only install the type of dust cap on
the cylinder valve outlet that is provided with the cylinder

valve. Other types of caps or plugs may result in leakage

of propane.

If the following information is not followed exactly, a fire
causing death or serious injury may occur.

[] Do not store a spare LP gas cylinder under or near this

outdoor cooking gas appliance.

[] Never fill the cylinder beyond 80 percent full.

SAVE THESE

iNSTRUCTiONS

TABLEOF CONTENTS

TABLE DES MATIERES

OUTDOOR BUILT-IN SIDE BURNER SAFETY ............................ 2

INSTALLATION REQUIREMENTS ................................................ 5

Tools and Parts ............................................................................ 5

Location Requirements ................................................................ 6

Product Dimensions ..................................................................... 6

Cabinet Dimensions ..................................................................... 6

Electrical Requirements ............................................................... 9

Gas Supply Requirements ......................................................... 10

Gas Connection Requirements - For Models Equipped for

LP Gas ........................................................................................ 10

Gas Connection Requirements - For Models Equipped for

Natural Gas................................................................................. 12

INSTALLATION INSTRUCTIONS ................................................ 13

Built-in Outdoor Side Burner Installation ................................... 13

Install Tank Tray for 20 Ib LP Gas Fuel Tank - For Models

Equipped for Use with a 20 Ib LP Tank ..................................... 13

GAS CONVERSIONS .................................................................... 17

Tools and Parts for Gas Conversion .......................................... 17

Conversion to a Local LP Gas Supply ....................................... 17

Conversion from LP Gas to Natural Gas ................................... 18

Check and Adjust the Burners ................................................... 19

USING YOUR OUTDOOR SIDE BURNER .................................. 20

Lighting Your Side Burner .......................................................... 20

OUTDOOR SIDE BURNER CARE ............................................... 21

General Cleaning ........................................................................ 21

TROUBLESHOOTING .................................................................. 22

ASSISTANCE OR SERVICE ......................................................... 22

In the U.S.A................................................................................ 23

Accessories ................................................................................ 23

In Canada ................................................................................... 23

WARRANTY .................................................................................. 23

SI_CURITI_ DU BRULEUR LATI_RAL

ENCASTRI_ D'EXTI_RIEUR .......................................................... 25

EXIGENCES D'INSTALLATION ................................................... 27

Outillage et pieces ...................................................................... 27

Exigences d'emplacement ......................................................... 28

Dimensions du produit ............................................................... 28

Dimensions du placard .............................................................. 28

Specifications electriques .......................................................... 31

Specifications de I'alimentation en gaz ..................................... 32

Exigences concernant le raccordement au gaz - Pour les

modeles equipes pour le propane ............................................ 33

Exigences concernant le raccordement au gaz - Pour les

modeles equipes pour le gaz naturel ......................................... 34

INSTRUCTIONS D'INSTALLATION ............................................. 35

Installation du brQleur lateral d'exterieur encastre ..................... 35

Installation du chariot de bouteille de gaz propane de 20 Ib -
Pour les modeles equipes pour I'utilisation d'une bouteille

de gaz propane de 20 Ib ............................................................ 35

CONVERSIONS DE GAZ .............................................................. 39

Outillage et pieces ...................................................................... 39

Conversion au gaz propane local .............................................. 40

Conversion de gaz propane &Gaz naturel ................................ 41

Contr61e et reglage des brQleurs................................................ 42

UTILISATION DU BRULEUR LATI_RAL D'EXTI_RIEUR ............ 43

Allumage du brQleur lateral........................................................ 43

ENTRETIEN DU BRULEUR LATI'--RALD'EXTI_RIEUR .............. 44

Nettoyage general ...................................................................... 44

DI_PAN NAGE................................................................................. 45

ASSISTANCE OU SERVICE ......................................................... 46

Accessoires ................................................................................ 46

Au Canada .................................................................................. 46

GARANTIE ..................................................................................... 47

INSTALLATION REQUIREMENTS

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

20 Ib LP Gas Models Natural Gas Models

Tools Needed

• Tape measure • Wrench or pliers

• Small, flat-blade screwdriver • Pipe wrench

• Flat-blade screwdriver • Scissors or cutting pliers

• #2 and #3 Phillips screwdriver (to remove tiedowns)

• Level • Noncorrosive leak-

Parts Supplied

• Gas pressure regulator/hose assembly set for 11" WCP LP
gas (attached to manifold)

• 1 single-prong plug/5,000 mAmp transformer assembly

• Convertible regulator set for 4" WCP Natural gas

• Orifices for Natural gas conversion

• LP gas fuel tank tray

Parts Needed

• 20 Ib LP gas fuel tank - approximately 18" (45.7 cm) height
and 12" (30.5 cm) diameter

detection solution

Tools Needed

• Tape measure • Wrench or pliers

• Small, flat-blade screwdriver • Pipe wrench

• Flat-blade screwdriver • Scissors or cutting pliers

• #2 and #3 Phillips screwdriver (to remove tiedowns)

• Level • Noncorrosive leak-
detection solution

Parts Needed

• Gas line shutoff valve

• 1/2"male pipe thread nipple for connection to pressure
regulator

• LP gas-resistant pipe-joint compound

• CSA design-certified outdoor flexible stainless steel
appliance connector (4-5 ft [1.2-1.5 m]) or rigid gas supply

line as needed.

Parts Supplied

• Convertible regulator set for 4" WCP Natural gas.

• Single-prong plug/5,000 mAmp transformer assembly

I _%(*a_HH__?_:__H_"__'__!C

Selectalocationthatprovidesminimumexposuretowindand
trafficpaths.Thelocationshouldbeawayfromstrongdraft

areas.
Donotobstructflowofcombustionandventilationair.
Clearancetocombustibleconstructionforbuilt-inoutdoorside

burners:

• Aminimumof24"(58cm)mustbemaintainedbetweenthe
sidesandbackandanycombustibleconstruction.

• Azeroclearancemaybemaintainedbelowthecooking
surfaceandanycombustibleconstruction.

Ignition

A grounded, 3-prong outdoor GFI outlet is to be located inside
the island cabinet and to the left of the side burner. See

"Electrical Requirements" section.

Style 1 - Front to Back Built-In Dual Side Burners

A

7-

B

© ©

i

E

F

Style 2 - Side bySide Built-In Dual Side Burners

L

T

B

© ©

i

< C

E_

r"

A.24" (61 cm)
B. 10%"(27 em)
C.28" (71.1em)
D.201/_"(52.1 em)

Built-In Outdoor Side Burner Enclosure

This built-in outdoor side burner is for installation in a built-in

enclosure constructed of combustible and non-combustible
materials. Some types of non-combustible materials could be
brick, firewall or steel. Some types of combustible materials

could be wood or laminate.

The enclosure for the built-in outdoor side burner is to be a

minimum of 11" (28.0 cm) high x 23" (58.4 cm) deep x
14" (35.6 cm) wide for front to back model and 11" (28.0 cm)

high x 17" (43.2 cm) deep x 25" (63.5 cm) wide for side by side
model.

E. 191/_"(49.5 em)

F. Manifold pipe
G.43/8"(11.1 cm)
H. 17" (43.2 cm)

F

f

G

Counter or support surfaces must be level.

The installation of this side burner must conform with local codes

A. 13" (33 cm)
B. 10%" (27 cm)

C. 17" (43.2 cm)

D. 26%" (67 cm)

6

E.253/8" (64.5 cm)
F. Manifold pipe

G. 4%" (11.1 cm)
H. 223/4'' (57.8 cm)

or, in the absence of local codes, with either the National Fuel
Gas Code, ANSI Z223.1/NPFA 54, Natural Gas and Propane
Installation Code, CSA B149.1, or Propane Storage and Handling
Code, B149.2.

Copies of the standards listed may be obtained from:
CSA International

8501 East Pleasant Valley Rd.
Cleveland, Ohio 44131-5575

NOTE: The outdoor side burner drops into the enclosure opening
and is supported by its side flanges. No bottom support is

needed.

The dimension chart and illustration below include cutout dimensions and minimum spacing requirements for all built-in outdoor
products. The illustration is for reference. The design of your cabinet layout can be personalized, but the dimensions for the cutouts and
minimum spacing must be followed.

C

E

E

K

F

Between 2 or more sets of Access Doors adjacent to each other:

K = 14" (35.6 cm) when 2 adjacent doors are opened to 90 degrees
K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees
Between a set of Access Doors and a Trash Drawer, Utility Drawer, Warming Drawer, Refrigerator, or Ice Maker:
K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees
Between a Trash Drawer, Utility Drawer, or Warming Drawer:
K = 3" (7.6 cm)

H A

With outdoor refrigerator

Grill with insulated jacket
Grill without insulated jacket

Cabinet Height and Depth Dimensions

Dimension A Minimum

37" (94.0 cm)
361/2'' (92.7 cm)
351/2'' (90.2 cm)

Dimension B Minimum

26" (66.0 cm)
27" (68.6 cm)
26" (66.0 cm)

Cutout Dimensions - Built-in Grill

Grill Size Dimension C Dimension D Dimension E

27" (68.6 cm) 29%" (75.2 cm) 10%" (27.3 cm) 227/8"(58.1 cm)
36" (91.4 cm) 388/8'' (98.1 cm) 10%" (27.3 cm) 227/8'' (58.1 cm)
48" (121.9 cm) 508/8'' (128.6 cm) 103A'' (27.3 cm) 227/8'' (58.1 cm)

Cutout Dimensions - Built-in Grill with Insulated Jacket

Grill Size Dimension C Dimension D Dimension E
27" (68.6 cm) 33" (83.8 cm) 11%" (29.8 cm) 24" (61.0 cm)

36" (91.4 cm) 42" (106.7 cm) 11%" (29.8 cm) 24" (61.0 cm)
48" (121.9 cm) 54" (137.2 cm) 11%" (29.8 cm) 24" (61.0 cm)

Burner Position Dimension C Dimension D Dimension E

Front to Back 131/2"(34.3 cm) 10%" (27.3 cm) 228/8'' (57.5 cm)
Side by Side 241/2'' (62.2 cm) 103A'' (27.3 cm) 167/8"(42.9 cm)

Cutout Dimensions - Built-in Sear Burner

Dimension C Dimension D Dimension E
131/2"(34.3 cm) 108/8'' (27.0 cm) 221Vie'' (57.6 cm)

Cutout Dimensions - Built-in Refreshment Center

Dimension C Dimension D Dimension E

301/2"(77.5 cm) 10%" (27.3 cm) 23" (58.4 cm)

Cutout Dimensions - Built-in Access Doors

Door Size Dimension F Dimension L*

18" (45.7 cm) 163/le'' (41.1 cm) 11/2"(3.8 cm)
27" (68.6 cm) 251/8'' (63.8 cm) 11/2"(3.8 cm)
30" (76.2 cm) 281/8'' (71.4 cm) 11/2"(3.8 cm)
36" (91.4 cm) 341/8'' (86.7 cm) 11/2"(3.8 cm)
48" (121.9 cm) 461/8'' (117.2 cm) 11/2'' (3.8 cm)

*Dimension L is the minimum mounting surface area around the opening for mounting the optional door or drawers.

Cutout Dimensions - Outdoor Refrigerator

Dimension G Dimension H

24" (61.0 cm) 351_'' (89.5 cm)

Dimension G Dimension H

18" (45.7 cm) 34" (86.4 cm) min. to 341/2'' (87.6 cm) max.

8

Cutout Dimensions - Built-in Warming Drawer

Warming Drawer Size Dimension J

24" (61.0 cm) 221/2"(57.2 cm)

Dimension M Dimension L*

12W' (31.1 cm) 11/2"(3.8 cm)

*Dimension L is the minimum mounting surface area around the opening for mounting the optional door or drawers.

Built-in Outdoor Grill Enclosure Ventilation for LP Gas:

An enclosure for an LP gas fuel tank is to be ventilated by
openings at both the top and lower levels of the enclosure.

If converting to LP gas these vents are to be in the enclosure:

An enclosure for use with an LP gas fuel tank for built-in
installation is to have at least one ventilation opening on an
exposed exterior side located within 5" (12.7 cm) of the top is to
be a minimum of 20 in.2 (129.0 cm2). One ventilation opening
within 1" (2.5 cm) of the bottom of the enclosure and the bottom
opening is to be a minimum of 10 in.2(64.5 cm_).All vent
openings are to be unobstructed. Every opening is to be a
minimum of 1/8"(0.32 cm) wide.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.

Do not use an extension cord.
Failure to follow these instructions can result in death,

fire, or electrical shock.

If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.

Check with a qualified electrician if you are not sure whether the
side burner is properly grounded.

A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical supply is
required.

It is recommended that a separate circuit servicing only this side
burner be provided.

• To avoid electrical shock, do not immerse cord or plugs in
water or other liquid.

• Unplug from the outlet when not in use and before
cleaning. Allow to cool before putting on or taking off
parts.

Do not operate any outdoor cooking gas appliance with a
damaged cord, damaged plug, or after the appliance
malfunctions or has been damaged in any manner.
Contact the manufacturer for repair.

Do not let the cord hang over the edge of a table or touch
hot surfaces.

• Do not use an outdoor cooking appliance for purposes
other than intended.

When connecting, first connect plug to the outdoor
cooking gas appliance then plug appliance into the outlet.

Use only a Ground Fault Interrupter (GFI) protected circuit
with this outdoor cooking gas appliance.

Do not remove the ground prong or use with an adapter
of 2 prongs.

The model/serial number rating plate is located on the right-hand

side panel. See the following illustration.

A. Model/serial number plate

Recommended Ground Method

The outdoor side burner, when installed, must be electrically
grounded in accordance with local codes or, in the absence of
local codes, with the National Electrical Code ANSl/NFPA 70, or
Canadian Electrical Code, CSA C22.1.

Copies of the standards listed above may be obtained from:
CSA International

8501 East Pleasant Valley Rd.
Cleveland, Ohio 44131-5575

National Fire Protection Association
One Batterymarch Park

Quincy, Massachusetts 02269

S ..............................

A ....................

Gas Conversion:
No attempt shall be made to convert the side burner from the gas

specified on the model/serial rating plate for use with a different
gas type without consulting the serving gas supplier. The
conversion kits supplied with the side burner must be used. See

"Gas Conversions" section for instructions.

Gas Pressure Regulator

The gas pressure regulator supplied with this side burner must be

used. The inlet (supply) pressure to the regulator should be as
follows for proper operation:

LP Gas:

Set pressure: 11" (27.9 cm) WCP
Inlet (supply) pressure: 11" to 14" (27.9 cm to 35.5 cm) WCP

Natural Gas:
Set pressure: 4" (10.2 cm) WCP

Inlet (supply) pressure: 7" to 14" (17.8 cm to 35.5 cm)
WCP maximum.

Contact local gas supplier if you are not sure about the inlet
(supply) pressure.

Burner Requirements for High Altitude

A. 3 prong ground plug

B. 3-prong polarized type outdoor GFI outlet

C. Ground prong

Explosion Hazard

Use a new CSA international approved "outdoor"
gas supply line.

Securely tighten all gas connections.
if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water

column.

Examples of a qualified person include:
licensed heating personnel,

authorized gas company personnel, and
authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances.
IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must
conform with American National Standard, National Fuel Gas

Code ANSI Z223.1 - latest edition or CAN/CGA B149.1 - latest
edition.

IMPORTANT: The side burner must be connected to a regulated
gas supply.

Refer to the model/serial rating plate for information on the type
of gas that can be used. If this information does not agree with
the type of gas available, check with your local gas supplier.

Input ratings shown on the model/serial rating plate are for
elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a
rate of 4% for each 1,000 ft (304.8 m) above sea level. Orifice
conversion is required. See "Assistance or Service" section to

order.

Gas Supply Line Pressure Testing

Testing above 1/2psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge):

The side burner and its individual shutoff valve must be

disconnected from the gas supply piping system during any
pressure testing of that system at test pressures greater than
1/2psi (3.5 kPa).

Testing below 1/2psi (3.5 kPa) or 14" (35.5 cm) WOP (gauge) or

lower:

The side burner must be isolated from the gas supply piping

system by closing its individual manual shutoff valve during any
pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2psi (3.5 kPa).

20 Ib LP Gas FuelTank

This side burner is equipped for use with a 20 Ib LP gas fuel tank

(fuel tank not supplied). A gas pressure regulator/hose assembly
is supplied.

It is also design-certified by CSA International for local LP gas
supply or for Natural gas with appropriate conversion.

\

A. Gaspressure regulator/hose assembly

10

The 20 Ib LP gas fuel tank must be mounted and secured.

Door Style Tank Tray

1. Open cabinet doors.

2. Pull out the tank tray.

The gas supply line shall be equipped with an approved shutoff

valve. This valve should be located in the same area as the side
burner and should be in a location that allows ease of opening

and closing. Do not block access to the shutoff valve. The valve
is for turning on or shutting off gas to the side burner.

B

Tank tray

3. Place the 20 Ib LP gas fuel tank bottom collar into the
mounting hole in the tank tray.

4. Tighten the locking screw against the bottom collar of the
20 Ib LP gas fuel tank to secure.

B C

A. Locking screw
B. Mounting hole

C. Bottom collar

5. Slide tank tray back into the cabinet.

6. Close cabinet doors.

Local LP Gas Supply Conversion

Conversion must be made by a qualified gas technician. The
qualified gas technician shall provide the gas supply to the

selected side burner location in accordance with the National
Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition, and local
codes. For conversion to local LP, the convertible regulator in the

conversion kit supplied with the side burner must be used.
IMPORTANT: The gas installation must conform with local

codes, or in the absence of local codes, with the National Fuel
Gas Code, ANSI Z223.1/NFPA 54 - latest edition. The qualified
LP gas technician shall provide the LP gas supply to the selected

side burner location in accordance with the National Fuel Gas
Code, ANSI Z223.1/NFPA 54 and local codes.

Follow instructions for converting to local LP gas in the "Gas
Conversions" section.

A. Gas supply line
B. Shutoff valve "open" position

C. To side burner

Natural Gas Conversion

Conversion must be made by a qualified gas technician. The
qualified Natural gas technician shall provide the Natural gas
supply to the selected side burner location in accordance with

the National Fuel Gas Code ANSI Z223.1/NFPA 54 - latest
edition, and local codes. For conversion to Natural gas, the

Natural gas conversion kit supplied with the side burner must be
used.

IMPORTANT: The gas installation must conform with local
codes, or in the absence of local codes, with the National Fuel
Gas Code, ANSI Z223.1/NFPA 54 - latest edition.

To convert to Natural gas, the Natural Gas Conversion Kit

supplied with the side burner must be used. Follow instructions
for converting to Natural gas in the "Gas Conversions" section.

C

A. New CSA International approved

"outdoor" flexible gas supply line

B. Rear of side burner
C. To Natural gas supply

The gas supply line shall be equipped with an approved shutoff

valve. This valve should be located in the same area as the side
burner and should be in a location that allows ease of opening

and closing. Do not block access to the shutoff valve. The valve
is for turning on or shutting off gas to the side burner.

A. New CSA International approved

"outdoor" flexible gas supply line

B. Rear of side burner
C. To local LP gas supply

B

A. Gas supply line
B. Shutoff valve "open" position

C. To side burner

11

11111111121XI(

Natural Gas LP Gas Conversion Using a Local LP Gas Supply

Built-in side burner models are equipped for use with Natural
gas. They are design-certified by CSA International for LP
(propane or butane) gases with appropriate conversion.

Built-in models are set for Natural gas use and have a pressure
regulator with 1/2"female pipe threads.

A

=%

D ..........C

A. Side burner gas pipe
B. New CSA International approved

"outdoor" flexible gas supply line

C. Rear of side burner
D. To Natural gas supply

The supply line shall be equipped with an approved shutoff valve.
This valve should be located in the same area as the side burner

and should be in a location that allows ease of opening and
closing. Do not block access to the shutoff valve. The valve is for

turning on or shutting off gas to the side burner.

B

Conversion must be made by a qualified person. A qualified
Natural gas technician shall provide the LP gas supply to the

selected side burner location in accordance with the National
Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition, and local

codes.

To convert to LP gas, the LP Gas Conversion Kit Part Number

W10118099 must be used. Follow instructions included with kit.

A

=¢=/

I//

"C

A. Side burner gas pipe
B. New CSA International approved

"outdoor" flexible gas supply fine

C. Rear of side burner
D. To local gas supply

LP Gas Conversion Using a 20 Ib LP Gas Fuel Tank

To convert to LP gas, the LP Gas Conversion Kit Part Number

W10118099 must be used. Follow instructions included with kit.

A 20 Ib LP gas fuel tank must be purchased separately.

A

A. Gas supply line
B. Shutoff valve "open" position

C. To side burner

12

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install side
burner.

Failure to do so can result in back or other injury.

3. Remove the top nuts (4) from the tank tray assembly and lift

the tank tray off of the mounting brackets.

Unpack side burner. Remove all packaging materials and
remove side burner from carton.

Place side burner into outdoor enclosure, but leave enough
room in back to connect to gas supply and electrical single
prong plug-in.

ss ,,_ .......

1. Position the tank tray for 201b LP gas fuel tank in the island
cabinet.

21/4"

(5.7 crn)

centerline of
tank tray

20%" 18%"

A. Top nut
B. Tank tray
C. Bottom nut

D. Bolt

E. Mounting bracket

4=

Install the tank tray mounting brackets to the base or floor of
the island using the proper size and type of mounting
hardware (not supplied). Tighten mounting hardware.

B

/

3"

(7.6 crn)

A. Screw (Use proper screw for island floor material.)
B. Lock washer

C. Flat washer

5. Pre-adjust each of the bottom nuts on the mounting brackets
to 3" (7.6 cm) from the base of the island to the top of the

nuts.

6. Remount the tank tray back onto the mounting brackets.
Replace the 4 top nuts but do not tighten.

Dimension A Dimension B

Front to back burner 83/32"(20.6 cm) 163/16"(41.1 cm)
Side by side burner 12%d' (31.9 cm) 25V8" (63.8 cm)

2. Square the tank tray mounting brackets and mark the
mounting hole locations in the island base.

A0

B

C

A. 20 Ib LP gas fuel tank
B. Tank tray for 20 Ib gas fuel tank
C. Top nut (do not tighten)
D. Mounting bracket

13

7=

The tank tray for the 20 Ib LP gas fuel tank must be adjusted
so that the bottom of the tank tray is %" (0.32 cm) above the
cabinet door opening and is level. The top nut on each of the
mounting brackets is to be loose. Turn the bottom nuts
counterclockwise to raise the tank tray and turn the bottom
nuts clockwise to lower the tank tray. When the tank tray is
level and slides in and out without touching the cabinet door
opening at the bottom or top with the 20 Ib LP tank installed,
tighten the top nuts against the adjustment flange.

A B

A. Top nut loosened
B. Top nut tightened

NOTE: A bracket or shelf (not supplied) that is large enough
to keep a second 20 Ib LP gas fuel tank from being stored in
the storage area under the side burner is required to be

mounted inside the island.

To Install the 20 Ib LP Gas Fuel Tank:

1. Open cabinet doors.

2. Pull out the tank tray.

Tank tray

3. Place the 20 Ib LP gas fuel tank bottom collar into the
mounting hole in the tank tray.

4. Tighten the locking screw against the bottom collar of the
20 Ib LP gas fuel tank to secure.

B C

Make Gas Connection

Gas Connection to a 20Ib LP Gas FuelTank

Explosion Hazard

Use a new CSA international approved "outdoor"
gas supply line.

Securely tighten all gas connections.
if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 crn) water

column.

Examples of a qualified person include:
licensed heating personnel,

authorized gas company personnel, and
authorized service personnel.

Failure to do so can result in death, explosion, or fire.

A. Locking screw
B. Mounting hole

C. Bottom collar

5=

Screw the gas pressure regulator/hose assembly to the 20 Ib
LP gas fuel tank as shown. (To disconnect, turn off the gas
supply to the 20 Ib LP gas fuel tank, then unscrew the gas
pressure regulator/hose assembly from the 20 Ib LP gas fuel
tank as shown.)

B

A

A. 20 Ib LP gas fuel tank
B. Gaspressure regulator/hose assembly

If converting to local LP or Natural gas, follow the instructions in
the "Gas Conversions" section.

IMPORTANT: A 20 Ib LP gas fuel tank must be purchased
separately.

IMPORTANT: The gas pressure regulator/hose assembly
supplied with the side burner must be used. Replacement gas
pressure regulator/hose assembly specific to your model, is
available from your outdoor side burner dealer.

14

6. Turn on the gas supply. Wait a few minutes for gas to move
through the gas line.

7. Test all connections by brushing on an approved
noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

8. Slide tank tray back into the cabinet.

9. Go to "Plug in Side Burner" in this section.

Gas Connection to Natural Gas or Local LP Gas

Explosion Hazard

Use a new CSA International approved "outdoor"
gas supply line.

Securely tighten all gas connections.
If connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water

column.

Examples of a qualified person include:
licensed heating personnel,

authorized gas company personnel, and
authorized service personnel.

Failure to do so can result in death, explosion, or (ire.

This installation must conform with local codes and ordinances.
In the absence of local codes, installations must conform with

either the National Fuel Gas Code ANSI Z223.1 - latest edition, or
CAN/CGA-B149.1 Natural Gas and Propane installation code.

Copies of the standards listed above may be obtained from:
CSA International

8501 East Pleasant Valley Rd.
Cleveland, Ohio 44131-5575

National Fire Protection Association
One Batterymarch Park

Quincy, Massachusetts 02269

1. Make gas connections.
A combination of pipe fittings must be used to connect the

side burner to the existing gas line.

• If local codes permit, use an outdoor flexible stainless

steel tubing gas connector, design-certified by CSA
International, to connect the side burner to the rigid gas
supply line. A 5/8"diameter line is recommended. Using a
wrench to tighten, connect the gas supply to the side
burner. Use pipe-joint compound on all non-flared male
threads. Do not kink or damage the flexible connector
when moving the side burner.

• Pipe-joint compounds suitable for use with LP gas must

be used. Do not use TEFLON ®ttape.

2. Open the manual shutoff valve in the gas supply line. The
valve is open when the handle is parallel to the gas pipe.

A. Closed valve
B. Open valve

3. Test all connections by brushing on an approved
noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

Plug in Side Burner

NOTE: This built-in outdoor side burner comes with a large

5000 mAmp power transformer/plug assembly for the side
burner igniters. Follow the instructions for plugging in and
mounting the power transformer. Keep any electrical supply cord
away from any heated surfaces.

1. Plug the single-prong plug into the receptacle on the left
underside of the side burner.

A

A. Single-prongplug

2.

Locate or build a non-combustible surface inside the island
cabinet to mount the power transformer. It must be to the left

side of the side burner at a minimum of 3" (7.6 cm) from the
side and 4" (10.2 cm) below the bottom of the side burner.

3.

Mount the power transformer to the mounting surface using
4 #8 screws (not supplied) that are the proper type and length
for the transformer and the mounting surface. It must be
mounted with the wire for the single-prong plug upward or

toward the side burner.
NOTE: The cord must be properly mounted with a cord

retention device so that its 3-prong plug will not touch the
ground when it is unplugged.

H

C

A. New CSA International approved

"outdoor" flexible gas supply line

B. Rear of side burner
C. To Natural gas or Local LP gas supply

1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

15