How it Works
KitchenAid
Loading...
KBHS109SSS03
Installation Guide
12 pgs1.05 Mb0
User Manual
8 pgs819.96 Kb0
Owner’s Manual
44 pgs6.15 Mb0

KitchenAid KBHS109SSS03, KBHS109SSS04, KBHS109SSS05, KBHS179SSS00, KBHS179SSS01 Installation Guide

...
INSTALLATIONINSTRUCTIONS
27" (68.6 CM) AND 30" (76.2 CM) ELECTRICBUILT-IN
MICROWAVE OVEN
. INSTRUCTIONS D'INSTALI.A,TIpN
FOURA MICRO-ONDES ENCASTREELECTRIQUE
DE 27" (68,6 CM) ET30" (76,2 CM)
TableofContents/Tabledes mati@res
BUILT-IN MICROWAVE OVEN SAFETY .......................................1
INSTALLATION REQUIREMENTS ................................................ 2
INSTALLATION INSTRUCTIONS .................................................. 4
SECURITI :!:DU FOUR ,_,MICRO-ONDES ENCASTRI :!:................. 6
EXIGENCES D'INSTALLATION ..................................................... 7
INSTRUCTIONS D'INSTALLATION ............................................... g
Installation du four a micro-ondes ............................................. 11
Achever I'installation .................................................................. 11
BUILT-INMICROWAVEOVENSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
8304424A
INSTALLATIONREQUIREMENTS
Product Dimensions
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed
here.
Tools needed
• Philips screwdriver •
• Measuring tape
• Level •
Hand or electric drill (for wall cabinet installtions)
1" (25 mm) drill bit (for wall cabinet installations)
Parts needed
• A UL listed or CSA approved conduit connector
• UL listed wire connectors
Parts supplied
• 2 screws Check local codes. Check existing electrical supply. See
"Electrical Requirements." It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
IMPORTANT"Observe all governing codes and ordinances.
• Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance with
microwave oven.
• Recessed installation area must provide complete enclosure around the recessed portion of the microwave oven.
• Grounded electrical supply is required. See "Electrical Requirements" section.
Electrical supply junction box should be located 3" (7.6 cm) maximum below the support surface when the microwave oven is installed in a wall cabinet. A 1" (2.5 cm) minimum diameter hole should have been drilled in the right rear or left rear corner of the support surface to pass the appliance cable
through to the junction box. NOTE: For undercounter installation, it is recommended that
the junction box be located in the adjacent right or left cabinet. If you are installing the junction box on rear wall behind the microwave oven, the junction box must be recessed and located in the upper or lower right or left corner of the cabinet; otherwise, the microwave oven will not fit into the cabinet opening.
• Microwave oven support surface must be solid, level and flush with bottom of cabinet cutout. Floor must be able to
support a weight of 110 Ibs (50.0 kg).
27" (68.6 cm) and 30" (76.2 cm) Microwave Ovens
27" (68.6 cm) models A. 25_8" (64.3 cm) recessed
width
B. 20_£' (51.6 cm) overall height C. 26_" (67.9 cm) overall width D. 23" (58.3 cm) max. recessed
depth
E. 18_" (47.6 cm) recessed
height
30" ('76.2 cm) models A. 28_?' (71.9 cm) recessed
width
B. 20_£' (51.6 cm) overall height C. 29_" (75.6 cm) overall width D. 23" (58.3 cm) max. recessed
depth
E. 18_" (47.6 cm) recessed
height
Cabinet Requirements
27" (68.6 cm) and 30" (76.2 cm) Microwave Ovens
_A
B
F _D
C
Y
27" (68.6 cm) models
A. 27" (68.6 cm) min. cabinet
width
B. 1" (2.5 cm) top of cutout to
bottom of upper cabinet door
C. 4_' (101.2 cm) bottom of
cutout to floor (recommended)
D. 25 _" (64.8 cm) cutout width
E. 1_" (3.8 cm) min. bottom of
cutout to top of cabinet door
F. !9_/' (49.4 cm) cutout height
30" (76.2 cm) models
A. 30" (76.2 cm) min. cabinet
width
B. 1" (2.5 cm) top of cutout to
bottom of upper cabinet door
C. 4_' (101.2 cm) bottom of
cutout to floor (recommended)
D. 28 _" (72.4 cm) cutout width
E. 1½" (3.8 cm) min. bottom of
cutout to top of cabinet door
F. !9_" (49.4 cm) cutout height
Cabinet Side View
E_
A. 23 _" (59.1 cm) min. cutout depth B. 23" (58.4 cm) recessed oven depth
C. Oven front D. Recessed oven
E.Cabinet
_A_
_, B _
Electrical Connection
To properly install your microwave oven, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.
• Microwave oven must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. The model/serial number rating plate is located on the right-hand microwave oven frame.
D
/C
A. Model/serial number plate
ect cc} 8®q n m® s s
GROUNDING INSTRUCTIONS
For a permanently connected microwave oven:
The microwave oven must be connected to a grounded, metallic, permanent wiring system, or an equipment
grounding conductor should be run with the circuit conductors and connected to the equipment grounding terminal or lead on the microwave oven.
SAVE THESE iNSTRUCTiONS
If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local
codes. Check with a qualified electrical installer if you are not sure the
microwave oven is properly grounded. This microwave oven must be connected to a grounded metal,
permanent wiring system. Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code, ANSI/ NFPA 70-latest edition or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91-1atest edition, and
all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
When a 4-wire or 3-wire, single phase 120/208 or 120/240 volt, 60 Hz, AC only electrical supply is available, a 20-amp maximum circuit protection is required, fused on both sides
of the line. A time-delay fuse or circuit breaker is recommended.
Connect directly to the fused disconnect (or circuit breaker box) through flexible, nonmetallic sheathed, copper cable (with grounding wire). See "Make Electrical Connection"
section. Flexible cable from the microwave oven should be connected
directly to the junction box. Do not cut the conduit. The length of conduit provided is for
serviceability of the microwave oven. A UL listed or CSA approved conduit connector must be
provided. If the house has aluminum wiring follow the procedure below:
1. Connect a section of solid copper wire to the pigtail
leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors and/or tools
designed and UL listed for joining copper to aluminum. Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with
local codes and industry accepted wiring practices.
INSTALLATIONINSTRUCTIONS
Locate existing wiring to avoid drilling into or severing wiring during installation.
5. Route the flexible cable conduit from the microwave oven to the junction box through a UL listed or CSA approved conduit
connector.
6. Tighten screws on conduit connector.
7. See "Electrical Connection Options Chart" to complete installation for your type of electrical connection.
Excessive Weight Hazard
Use two or more people to move and install microwave oven.
Failure to do so can result in back or other injury.
2. To avoid floor damage, set the microwave oven onto cardboard prior to installation. Do not use handle or any
portion of the front frame for lifting.
3. Remove the shipping materials and tape from the microwave
oven.
4. Remove and set aside racks and other items from inside the microwave oven.
5. Remove the hardware package from inside the bag containing literature.
6. Move the microwave oven and cardboard close to the microwave oven's final location,
El®ctdccl Co[' ®ctio
Electrical Connection Options Chart
If your home has: Go to section:
4-wire 4-wire Cable from Home
Power Supply
1/2"
3-wire 3-wire Cable from Home
1/2"
Power Supply
)
4-Wire Cable from Home Power Supply
IMPORTANT: Use the 4-wire cable from home power supply in the U.S. where local codes do not allow grounding through neutral, New Branch circuit installations (1996 NEC), mobile homes and recreational vehicles, new construction and in
Canada.
Electrical Shock Hazard
Disconnect power before servicing. Use 12 gauge copper wire.
Electrically ground oven. Failure to follow these instructions can result in death,
fire, or electrical shock.
This microwave oven is manufactured with a neutral (white) power supply wire and a cabinet-connected green (or bare) ground wire twisted together.
1. Disconnect power.
2. Feed the flexible cable conduit from the microwave oven through the opening in the cabinet.
3. Remove junction box cover if it is present.
4. Install a UL listed or CSA approved conduit connector to the
junction box.
A. UL listed or CSA approved conduit connector
;JH
"% i
L_
A. Cable from home power supply B. Black wires
C. Red wires D. 4-wire flexible cable from
microwave oven
E. Junction box
1.
Connect the 2 black wires (B) together using a UL listed wire connector.
2.
Connect the 2 red wires (C) together using a UL listed wire connector.
3.
Untwist white wire from green (or bare) ground wire coming from the microwave oven,
4.
Connect the 2 white wires (F) together using a UL listed wire connector.
5.
Connect the green (or bare) ground wire (H) from the oven cable to the green (or bare) ground wire (in the junction box) using a UL listed wire connector.
6. Install junction box cover.
F. White wires
G. UL listed wire connectors H. Green (or bare) ground wires
I. UL listed or CSA approved
conduit connector
Loading...
+ 8 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use