KitchenAid 4KSRF42DT User Manual

KiCtchmmA#d*

42” (1067 m

Built-h

Refrigerator

Model 4KSRF42DT

i

IMPORTANT:

Installer:

I

lnstr~~ctions with the Homeowner.

Hommwr@r:

Instructions for future reference.

I

Save
local

Leave tnstallation

Keep Installation

Installation Instructions for

electrical inspector’s use.

Part No. 1113438

* Registered Trademark of KitchenAid, Inc., U.S.A., KitchenAid Canada, Inc.,

Licensee in Canada

d43

Before you start...

Proper installation is your
responsibility. Make sure you have
everything necessary for correct
installation. it is the responsibility of
the installer to comply with the
installation specifications provided.

The built-in refrigerator weighs over
400 Ibs (181 kg). The floor must be
sturdy enough to support this weight
plus the additional weight of door
panels, food and ice.

Grounded electrical outlet is
required. See Electrical
requirements.

Location of the built-in refrigerator
must permit the doors to open to
at least 90°.

Because of the weight and size of
the built-in refrigerator, two or more
people are needed to move and
safely install it.

Dimensions that are shown must

be used. Given dimensions provide

required 0” clearance.

One inch of space is required
between side of refrigerator and a
corner wall to allow the door to open
to at least a 90” angle.

NOTE:

It Is the customer’s

responsibility:

l

To contact a qualified

electrical installer.

9 To assure that electrical

installation Is adequate and in
conformance wlth local

codes and ordinances.

Electrical Shock Hazard

Special care must be taken
when drilling holes into the
wall of the house. ElectrIcal
wlres may be concealed
behind wall coverlng.

Personal Injury Hazard

l

Because of the welght and
size of the bull+In
refrlgerator, two or more
people are needed to move
and safely Install It.

l

Most of the refrlgerator’s
welght Is at the top. Extra
care Is needed when
movlng the refrlgerator to
prevent Upping.

Failure to do so could
result In personal Injury

Floor Damage

Keep cardboard shipplng piece
or plywood under refrlgerator
until It Is installed In operatlng
posltlon.

Failure to do so maycause
damage to floor covering.

Important: Observe all
governing codes and
ordinances.

Failure to meet codes and

ordinances could lead to
fire or electrical shock
hazard.

Tools and

materials needed

for installation:

Phllllps screwdrlver
5/16”(6 mm) and 3/4”

(19 mm) sockeI

and ratchet

l/4” (6 mm) copper

tublng

tubing cutler
eppllance dolly
116” (3 mm) Allen wrench
adjustable wrench
cardboard or plywood
6, #6, or larger wood

screws

2, wood boards -

32” (613 mm) fong
(See page 7 for
speclflcatlons.)

1 - 3/8” (35 mm) open

wrench - front leveler

stepladder
wrench set
knlk

3116” (5 mm)

and 114”

(6

mm)

drill bits

drill
screwdrlver
level
bucket

shutoff valve

stud locator
l/4” (6 mm)

nut driver

Parts supplied for installation:

top grille assembly
base grille
tube assembly
misc. parts bag
Icemaker bin assembly

Remove parts from packages.

Check that ail parts were included.

Parts that must be
ordered separately
or custom-made:

Acrylic door panel kits

Three colors of acrylic door panel
kits are available from your
KitchenAid dealer: White, Black

and Almond. Each kit includes door
panels, top grille panels and handle

inserts. Follow kit instructions
to install panels and inserts.

Klt Numbers for Acrylic Panels

;I

Custom door panels, handle
inserts and top grille panels

See page 4 for custom panel
dimensions and page 9, steps
9 -13 for installation.

Side panels

Check with your builder or installer
to see if you need side panels
that match your kitchen cabinets.
Side panels must be custom-made.
Side panel dimensions are given

on page 5.

Page 1

Dimensions for built-in area

Electrical outlet
should be centered
wlthln shaded area.

Width and depth of the built-in area
are determined by the type of
installation. The built-in refrigerator
can be installed with the doors flush
with the wall, with the doors
protruding from the wall, or with side
panels enclosing refrigerator. Select
one method of installation and use
the dimensions given for that
method as shown.

Height of built-in area can range
from a minimum of 82-l/2” (2096 mm)
to 84-W” (2153 mm).
Optional top grilles may be required
for enclosures less than 83-5/8”
(2124 mm).
Height dimensions with optional top
grilles are given on page 3.

&ouhded

01

let location

electrical

Wall

plumbing

location

l-114”

(32 mm)

13”
(330 mm) +

(178 ml

356

mm)

t

r

can be cut anywhere
within shaded areas.

+/- l/8” (3 mm) tolerance

Floor plumbing
location

r78

mm)

Page 2

Product dimensions

4- 23.718”

(696 mm)

Levelers extended l/8” (3 mm) below rollers

*- f;i4,

:sy)wldth

rece

T

82-112”

KZ.“~’

helght

top of houslng
to top of arllle

. .._.. . i”‘(l9l-mm) grille ..­l-118” (29 mm) max. -

wlth 8-112” (216 mm)

T

Height dlmenslons
when the mlnlmum
extension of levelers
[ll8” (3 mm) bdow
rollers] is used to
remove the welght
from the rollers:

83-S/8”

(2124 mm) helght

wlth

8-112”

(216 mm) grille’

85118” (2111 mm) helght

wlth 8” (293 mm) grille

82-5/8” (2999 mm) helght
wlth 7-W” (191 mm) grille

I

grille

,

w

w

*Top grille

The 8-l/2” (216 mm) top grille is
provided. Smaller top grilles must
be ordered from your KitchenAid
dealer.

Check the chart below for
the part numbers you need to order
for the size of top grille you need.

Optlonal Top Grilles

Size

7-112’

(191
mm)

Part

Number

- 4210546

4210545 R.&h;g;zm ;

Descrlptlon

p{h;gy$m ;
Decorative

side frame

Air vane

Decorative

side frame

Air vane

panel

panel

Ouantlty

Levelers

I

2

1

2

1

fully extended

83-518”
s’B’c’B”olF2

3.112”

P

(89 mm)

l-l /4” 132 mm\ bela

_ ., _ ._- ----- -, ----

w rollers

tOD 0f

houslna

tO’tOD

of orllleT

t

Helght dlmenslons
when the maxlmum
extenslon of levelers

l-114” (32

b

elow rollers] 1
used to remove
the wefght from
the rollers:

84-314”

hel ht wlth
8-1 2 (216 mm) Be*
grille’

84-114” (2140 mm)
helght wlth
V (293 mm) grille

83-314”

mm

s

(2153 mm)

(2127 mm)

Page 3