KISANKRAFT KK-WPP-10, KK-WPP-15, KK-WPP-21, KK-WPP-2535, KK-WPP-50080 User Manual

KisanKraft

®

Warranty Certificate

(DEALER COPY)

This warranty is null & void, if you fail to register the warranty with

KisanKraft by sending the KisanKraft Copy with dealer’s stamp.

KisanKraft Limited (formerly known as KisanKraft Machine Tools P Ltd)

: www.kisankraft.com

: [e-mail]

: +91.80.22178200

Page 1 of 44

Product

Centrifugal Water
Pump For
Agriculture

KisanKraft
Invoice Date

Brand

KisanKraft

KisanKraft
Invoice No.

Model

 KK-WPP-10
 KK-WPP-15
 KK-WPP-21
 KK-WPP-31
 KK-WPP-2535
 KK-WPP-50080

WARRANTY
PERIOD

6-MONTHS

FOR THE SPECIFIED PERIOD FROM THE DATE

OF SALE OR DELIVERY WHICHEVER IS
EARLIER.

Dealer’s

Invoice Date

Dealer’s Invoice

No.

Buyer’s Info (Name, Address, Phone, etc.):

Dealer’s Stamp (Address, Phone, TIN, etc.):

Buyer’s Sign

Dealer’s Sign

What is covered: KisanKraft Limited and its manufacturers warrant this product to be
free from defects in material or workmanship. All parts defective in material and
workmanship are covered.
This warranty will only cover defects arising under normal usage.
This warranty is limited to repair or replacement by KisanKraft Limited or its
manufacturers at the premises of Authorized Dealers, of such parts as appear to
KisanKraft or its manufacturers, upon inspection, to be defective in material and/or
workmanship. KisanKraft or its manufacturers make no warranty with respect to trade
accessories not manufactured or sold by them.
What is not covered: The warranty shall become null and void and neither KisanKraft
Limited nor any of its manufacturers, nor its authorized dealers assumes any
responsibility, if the failure was caused by the following:
(1) Operation of product with incorrect fuel or lubricants, (2) Incorrect usage of machine
or misuse, (3) Lack of maintenance, (4) Negligence, (5) Accident or physical damage,
(6) Repairs made by unauthorized parties and/or with unauthorized parts, (7) Improper
set up, adjustments, tampering or altered products

KisanKraft

®

Warranty Certificate

(DEALER COPY)

This warranty is null & void, if you fail to register the warranty with

KisanKraft by sending the KisanKraft Copy with dealer’s stamp.

KisanKraft Limited (formerly known as KisanKraft Machine Tools P Ltd)

: www.kisankraft.com

: [e-mail]

: +91.80.22178200

Page 2 of 44

Important: (1) Normal maintenance and adjustments to the product is the responsibility
of the customer. (2) Normal wear and tear is not covered under warranty
(3) Rubber/plastic parts and consumables such as blades, clutch and clutch-bell, spark­plugs, nylon line, air-filters, fuel-filters, oil seals etc. are not covered under the warranty.

No Warranty On Electrical Motor / Electrical Parts / Battery Etc.

Incidental / Consequential Loss: KisanKraft Limited or its manufacturers will not be

liable for general damages, including bodily injuries, or for incidental or consequential
damages including, but not limited to, loss of use, loss of profits, loss of production,
expense of substitute equipment or other commercial loss or damage.
Limitation of Liability: This limited warranty is in lieu of all other express warranties,
obligations, or liabilities. Any implied warranties, obligations or liabilities, including, but
not limited to, any implied warranty of merchantability shall be limited in duration to the
applicable warranty period. Any action for breach of any warranties hereunder,
including, but not limited to, any implied warranty of merchantability must be brought
within the applicable warranty period.
Modifications of Warranty: No agent, representative, dealer, or employee of
KisanKraft Limited or any of its manufacturers has the authority to increase or alter the
obligations of this warranty.
Assignment / Transfer of warranty: The warranty cannot be assigned and shall not
transfer if the product is resold by the first buyer. The above warranties are extended to
the first end user (original purchaser), and no warranty is made, nor authorized to be
made assignable on resale by the first end user.
What you must do to obtain limited warranty service: To obtain performance of any
obligation under this warranty for failure during the applicable warranty period, deliver
the defective product, to the nearest Authorized Dealer. KisanKraft Limited, its
manufacturers and its dealers reserve the right to inspect the claimed defective part(s)
to determine if the malfunction is the result of a defect covered by this warranty. Please
note that the decision of KisanKraft Limited with respect to any warranty claim is final.

Receipt is required for availing warranty services

Jurisdiction: All disputes are subject to Bangalore court’s jurisdiction.

Our

Products

ChainsawsBrush Cutters and AccessoriesHarvesters
Engines and Water PumpsHand Tools

Garden Tools



Cultivators and AccessoriesSprayers and Accessories



Transplanter and Post Hole Digger

Milking Machines

KisanKraft

®

Centrifugal Water Pump For

Agriculture

KK-WPP-10 /15 /21 /31 /2535 /50080

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 3 of 44

User Manual

KisanKraft Limited

(Formerly known as KisanKraft Machine Tools Pvt Ltd)

Sri Huchhanna Tower, #4,1st Main,7-A Cross, Maruthi Layout, Dasarahalli,

HAF Post, Hebbal, Bangalore 560024,Karnataka,INDIA

♦ Bangalore (HO) ♦ Ahmedabad ♦ Bhopal ♦ Bhubaneswar ♦ Coimbatore ♦

♦ Jammu ♦ Guwahati ♦ Jaipur ♦ Hubli ♦ Hyderabad ♦

♦ Karnal ♦ Kolkata ♦ Lucknow ♦ Pune ♦ Raipur ♦ Shimla ♦

KisanKraft

®

Centrifugal Water Pump For

Agriculture

KK-WPP-10 /15 /21 /31 /2535 /50080

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 4 of 44

Contents

BEFORE GETTING STARTED ............................................................................ 7

SAFETY INSTRUCTIONS .................................................................................. 7

OPERATION ................................................................................................... 7

PREPARATION BEFORE OPERATION: ........................................................... 7

STARTING THE ENGINE ............................................................................... 8

USE ............................................................................................................. 8

STOPPING THE ENGINE ............................................................................... 8

MAINTENANCE .............................................................................................. 8

STORAGE ....................................................................................................... 9

TROUBLESHOOTING ...................................................................................... 9

TECHNICAL SPECIFICATIONS ........................................................................ 10

WATER PUMP PARTS DIAGRAM & LIST-KK-WPP-10/15 ............................... 13

PUMP PARTS DIAGRAM & LIST-KK-WPP-21/31............................................ 14

USER MANUAL-4-STROKE PETROL ENGINE .................................................. 17

ENGINE PARTS DIAGRAM & LIST (KK-PE4-103) ............................................ 27

KisanKraft

®

Warranty Certificate

(CUSTOMER COPY)

This warranty is null & void, if you fail to register the warranty with

KisanKraft by sending the KisanKraft Copy with dealer’s stamp.

KisanKraft Limited (formerly known as KisanKraft Machine Tools P Ltd)

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 5 of 44

Product

Centrifugal Water
Pump For
Agriculture

KisanKraft
Invoice Date

Brand

KisanKraft

KisanKraft
Invoice No.

Model

 KK-WPP-10
 KK-WPP-15
 KK-WPP-21
 KK-WPP-31
 KK-WPP-2535
 KK-WPP-50080

WARRANTY
PERIOD

6-MONTHS

FOR THE SPECIFIED PERIOD FROM THE

DATE OF SALE OR DELIVERY WHICHEVER IS
EARLIER.

Dealer’s

Invoice Date

Dealer’s Invoice

No.

Buyer’s Info (Name, Address, Phone, etc.):

Dealer’s Stamp (Address, Phone, TIN, etc.):

Buyer’s Sign

Dealer’s Sign

What is covered: KisanKraft Limited and its manufacturers warrant this product to be
free from defects in material or workmanship. All parts defective in material and
workmanship are covered.
This warranty will only cover defects arising under normal usage.
This warranty is limited to repair or replacement by KisanKraft Limited or its
manufacturers at the premises of Authorized Dealers, of such parts as appear to
KisanKraft or its manufacturers, upon inspection, to be defective in material and/or
workmanship. KisanKraft or its manufacturers make no warranty with respect to trade
accessories not manufactured or sold by them.
What is not covered: The warranty shall become null and void and neither KisanKraft
Limited nor any of its manufacturers, nor its authorized dealers assumes any
responsibility, if the failure was caused by the following:
(1) Operation of product with incorrect fuel or lubricants, (2) Incorrect usage of
machine or misuse, (3) Lack of maintenance, (4) Negligence, (5) Accident or physical
damage, (6) Repairs made by unauthorized parties and/or with unauthorized parts, (7)
Improper set up, adjustments, tampering or altered products

KisanKraft

®

Warranty Certificate

(CUSTOMER COPY)

This warranty is null & void, if you fail to register the warranty with

KisanKraft by sending the KisanKraft Copy with dealer’s stamp.

KisanKraft Limited (formerly known as KisanKraft Machine Tools P Ltd)

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 6 of 44

Important: (1) Normal maintenance and adjustments to the product is the
responsibility of the customer. (2) Normal wear and tear is not covered under warranty.
(3) Rubber/plastic parts and consumables such as blades, clutch and clutch-bell,
spark-plugs, nylon line, air-filters, fuel-filters, oil seals etc. are not covered under the
warranty.

No Warranty On Electrical Motor / Electrical Parts / Battery Etc.

Incidental / Consequential Loss: KisanKraft Limited or its manufacturers will not be

liable for general damages, including bodily injuries, or for incidental or consequential
damages including, but not limited to, loss of use, loss of profits, loss of production,
expense of substitute equipment or other commercial loss or damage.
Limitation of Liability: This limited warranty is in lieu of all other express warranties,
obligations, or liabilities. Any implied warranties, obligations or liabilities, including, but
not limited to, any implied warranty of merchantability shall be limited in duration to the
applicable warranty period. Any action for breach of any warranty hereunder,
including, but not limited to, any implied warranty of merchantability must be brought
within the applicable warranty period.
Modifications of Warranty: No agent, representative, dealer, or employee of
KisanKraft Limited or any of its manufacturers has the authority to increase or alter the
obligations of this warranty.
Assignment / Transfer of warranty: The warranty cannot be assigned and shall not
transfer if the product is resold by the first buyer. The above warranties are extended
to the first end user (original purchaser), and no warranty is made, nor authorized to
be made assignable on resale by the first end user.
What you must do to obtain limited warranty service: To obtain performance of
any obligation under this warranty for failure during the applicable warranty period,
deliver the defective product, to the nearest Authorized Dealer. KisanKraft Limited, its
manufacturers and its dealers reserve the right to inspect the claimed defective part(s)
to determine if the malfunction is the result of a defect covered by this warranty. Please
note that the decision of KisanKraft Limited with respect to any warranty claim is final.

Receipt is required for availing warranty services

Jurisdiction: All disputes are subject to Bangalore court’s jurisdiction.

Our

Products

ChainsawsBrush Cutters and AccessoriesHarvesters
Engines and Water PumpsHand Tools

Garden Tools



Cultivators and AccessoriesSprayers and Accessories



Transplanter and Post Hole Digger

Milking Machines

KisanKraft

®

Centrifugal Water Pump For

Agriculture

KK-WPP-10 /15 /21 /31 /2535 /50080

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 7 of 44

BEFORE GETTING STARTED

Thank you for your purchase and use of our products. In order to avoid accidents or injury,
please read this manual carefully before using the machine. After reading, preserve it for
further reference.
This Water pump is characterized by light weight, simple structure high efficiency,
convenient use and flexible movement. It can be used for agricultural irrigation, drainage
construction and pumping, especially widely used in recurrent irrigation of small area for
agricultural production at present.

SAFETY INSTRUCTIONS

1. Read the operation manual carefully before starting the engine in order to avoid
any accident and damage.

2. Please do not use this engine inside an enclosed area. Ensure adequate
ventilation while Engine is in operation.

3. To prevent fire hazard, please keep the Engine in operation at least 1-meter (3
feet) away from Combustible or Inflammable materials, buildings and equipment.

4. When refueling you must STOP the Engine. Please do not smoke near Engine.
Wipe the spilled fuel after refueling.
CAUTION: Spilled fuel is a fire hazard.

5. Always place the engine horizontally. Do NOT tilt the Engine more than 21
degrees Overturning or inclining the engine may cause oil spillage and result in
fire hazard.

6. Do NOT cover the Engine when in operation.

7. Children are strictly not allowed near the engine operation area.

OPERATION

PREPARATION BEFORE OPERATION:

1. Connect the suction pipe:

• Place the filter into the empennage of the suction pipe with the tie-in.

• Place another end into the input with the tie-in.

2. Connect the discharging pipe:
Place the discharging pipe into the output with the tie-in.

3. Check the oil:

• Check the oil lever in the case that the engine is off and horizontal.

4. Check the fuel level:

• Open the crankcase cover to check the fuel level. Please add fuel when the lever
is low.

5. Check the air cleaner:

• Disconnect the papilionaceous (flower petal like) nut washer and air cleaner filter.

• Check whether the foam filter element is dirty or air logged. Clean it if necessary.

• Newly equip the air cleaner and operate the engine until it is well equipped.

KisanKraft

®

Centrifugal Water Pump For

Agriculture

KK-WPP-10 /15 /21 /31 /2535 /50080

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 8 of 44

• It would accelerate the abrasion if the dust or the pollutant is absorbed into the
engine through carburetor.

6. Check the water pump:

• Check whether the water is added into the pump.

• The pump must be fully filled with water before operating.

• Operate the pump until the water is added so as to protect the air proof from the

overheating in lasting operation without water.

STARTING THE ENGINE

1. Keep the fuel valve to “ON” position.

2. Shut down the throttle (throttle may be partly closing or open when the engine is
warm or in the case of high temperature).

3. Keep the switch in the ON position.

4. Slowly move the regulating handle to the left.

5. Pull the start handgrip when feeling the resistance, then drawback swiftly.

USE

The use of the water pump:

1. Gradually open the throttle when the engine’s warm.

2. Set a scheduled rotation speed.

STOPPING THE ENGINE

1. Move the regulating handle to the right.

2. Keep the switch in the “OFF” position.

3. Turn off the fuel valve.

MAINTENANCE

Oil:

Change the oil and quickly discharge the oil when the engine is hot. Replace the oil for the
first time after 50 hours of cumulative operation. After that, replace the oil per 500 hours
operation. The specific procedure is as follows:

• Disconnect the oil cap and drain plug, then discharge the oil, newly equip the
drain plug and screw it down.

• Add the clean oil to the appointed oil level.

Air cleaner filter:

Air flow in the carburetor is reduced if air cleaner is dirty. In order to clean it:

• Move the papilionaceous nut, and disconnect the air cleaner filter cover and the
foam filter element with apyrous cleaning and then air dry it.

• Dip the foam filter element into the clean oil and extrude the additional oil.
Newly equip the foam filter element and air cleaner filter.

Spark plug:
It would be kept 0.7-0.8 mm between the spark plug and no carbon so as to assure the
normal running

KisanKraft

®

Centrifugal Water Pump For

Agriculture

KK-WPP-10 /15 /21 /31 /2535 /50080

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 9 of 44

STORAGE

Cool the engine and keep the fuel valve in the “OFF” position before moving or storing

indoors to avoid the burning or fire.

1. Keep the storage place dry and less dust.

2. Clean the inner parts of the engine.

3. Replace the oil after completely discharging the fuel tank and the carburetor.

4. Disconnect the spark plug to infuse 2-3 grams of oil into the cylinder and rotate
the engine 3-4 times and then equip the spark plug.

5. Cover the pump cover to avoid dust.

TROUBLESHOOTING

Problem

Probable cause

Action to be taken

The Engine can’t be

started

Refer the Engine manual

Refer the Engine manual

The pump cannot pump
water

The water infused is not
enough

Fill the pump with enough
water.

The filter is air – logged.

Clear the air from the filter.

The tie-in is not firmly
equipped ,
Suction pile is leaking.

Ensure proper suction
Packing is proper and leak
free.

The pipe is damaged.

Replace the pipe.

Whether the head lift is too
high

Never exceed the rated
max. Lift, if so lower the
head lift.

Insufficient flux
Any block with impeller or
strainer

Remove the blockage in
the strainer

Gas leakage in inlet pipe

Fix any leakage in the pipe

Damage in impeller

Replace the impeller

KisanKraft

®

Centrifugal Water Pump For

Agriculture

KK-WPP-10 /15 /21 /31 /2535 /50080

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 10 of 44

TECHNICAL SPECIFICATIONS

Model

KK-WPP-10

KK-WPP-15

KK-WPP-2535

Rated power

1.15 kW

Displacement

98 cc

Engine Type

4-stroke

Engine Model

KK-PE4-103

Rated rotation speed
(rpm)

3600

Fuel Used

Petrol

Fuel Tank Capacity

1.3 liter

Oil- For Engine

350 ml (20W40 grade)

Net Weight

11 kg

12 kg

11.5 kg

Fuel Consumption

700 ml /hour

Inlet / Outlet Port
(Diameter)

25x25 mm

(1x1”)

38x38 mm

(1.5x1.5”)

25x25 mm

(1x1”)

Suction (vertical)

3m (depth)

4m (depth)

3m (depth)

Delivery (horizontal)

20 m

20 m

35 m

Max flow

58 L/M

200L/M

133L/M

Head lift

8 m

15 m

35 m

Output capacity

8000 Liter/hour

12000 Liter/hour

7000 Liter/hour

KisanKraft

®

Centrifugal Water Pump For

Agriculture

KK-WPP-10 /15 /21 /31 /2535 /50080

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 11 of 44

Model

KK-WPP-50080

Rated power

4 kW(5.4 hp)

Displacement

212 cc

Engine Type

4-stroke

Bore X Stroke

70X55 mm

Engine Model

KK-PE4-170

Rated rotation speed
(rpm)

3600

Fuel Used

Petrol

Fuel Tank Capacity

3.6 L

Oil- For Engine

0.6 L

Net Weight

25 kgs

Diameter of Suction
Pipe

50 mm (2”)

Diameter of Delivery
Pipe

2x 40mm (1.5”)+1x50mm(2”)

Suction (vertical)

5 m

Max flow

5 L/s

Head lift

80 m

KisanKraft

®

Centrifugal Water Pump For

Agriculture

KK-WPP-10 /15 /21 /31 /2535 /50080

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 12 of 44

Model

KK-WPP-21

KK-WPP-31

Type

Self-priming

Inlet/Outlet size(mm)

50

80

Max lift(m)

30

Suction(m)

5~8

Engine model

KK-PE4-163

KK-PE4-203

Engine type

OHV,Single-cylinder,4-stroke,forced air cooling

Displacement

163cc

196cc

Rated power

2.3 kW (3 hp)

3 kW (4 hp)

RPM

3600

Max. torque

10N.m/2500rpm

11N.m/2500rpm

Max discharge capacity
(Liters per Hour)

36,000

60,000

Fuel tank capacity

3.6L

Engine oil capacity

0.6L

N.W/G.W (kgs)

25/27

28/30

Dimension

490x395x450

515x410x460

KisanKraft

®

Centrifugal Water Pump For

Agriculture

KK-WPP-10 /15 /21 /31 /2535 /50080

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 13 of 44

WATER PUMP PARTS DIAGRAM & LIST-KK-WPP-10/15

KisanKraft

®

Centrifugal Water Pump For

Agriculture

KK-WPP-10 /15 /21 /31 /2535 /50080

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 14 of 44

Part No

Part Name

Part No

Part Name

1.

Gasket bump(Paper)A

19.

Bolt M6x16

2.

Connecting Board of bump

20.

Bolt M6x85

3.

Bolt M8x18

21.

Rubber Gasket, Inlet And
Outlet Pipe

4.

Washer 10

22.

Inlet And Outlet Pipe

5.

Gasket bump(Paper)B

23.

Flange Nut Inlet And Outlet
Pipe

6.

Handrail

24.

Hoop

7.

Bottom Cover Of bump

25.

Upper bump Body

8.

Seal

26.

O Ring

9.

Washer 6

27.

Rubber Plug

10.

Bolt M6x20

28.

Bolt M8x14

11.

Impeller

29.

Taper Filter

12.

Packing bump Body

30.

Frame Assy

13.

O Ring

31.

Bottom Rubber

14.

Turbine

32.

Bolt M8x14

15.

bump Body

33.

Bolt M6x14

16.

Bolt M6x50

34.

Nut M8

17.

Single-Direction Valve

35.

Spring Washer 8

18.

Upper Corer Of bump Body

36.

Washer 8

PUMP PARTS DIAGRAM & LIST-KK-WPP-21/31

Pump Set Contents

KisanKraft

®

Centrifugal Water Pump For

Agriculture

KK-WPP-10 /15 /21 /31 /2535 /50080

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 15 of 44

SL-No

KK-No

KK-Name

Qty

1

E1-01

Pump body

1 2 E1-02

Pump Cover

1 3 E1-03

Triangle flange

1

4

E1-04

Pump Elbow

1

5

E1-05

Impeller

1 6 E1-06

Turbine

1 7 E1-07

rubber gasket, Triangle flange

1 8 E1-08

Rectangular rubber gasket

1 9 E1-09

Rubber Plug

2

10

E1-10

O-Ring(Rubber Plug)

2

11

E1-11

O-ring(Turbine)

1

12

E1-12

Rubber gasket(Bolt)

5

13

E1-13

Water Seal assy

1

14

E1-14

Bolt M8x55 Flanged Hex

4

15

E1-15

Bolt M8x25 Flanged Hex(SPL)

4

16

E1-16

N/A 1 17

E1-17

Washer 8-Plain

4

18

E1-18

O-Ring(Pump body)

1

19

E1-19

Bolt M8x20 Hex

7

20

E1-20

Bolt M8x25 Hex

5

KisanKraft

®

Centrifugal Water Pump For

Agriculture

KK-WPP-10 /15 /21 /31 /2535 /50080

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 16 of 44

Frame

SL-No

KK-No

KK-Name

Qty

1

E2-01

Frame assembly

1 2 E2-02

Rubber Bedding

4

3

E2-03

Clamp(Hose)

3

4

E2-04

Inlet and outlet pipe

1 5 E2-05

Flange nut

1 6 E2-06

Rubber gasket, inlet and outlet pipe

1 7 E2-07

Filter

1

8

***

N/A

1

9

E2-09

Bolt M6x12 Flanged Hex

4

10

E2-10

N/A 4 11

E2-11

Nut M8 Flange

2

12

E2-12

Bolt M8x45 Flanged Hex

4

13

E2-13

N/A

2

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 17 of 44

USER MANUAL-4-STROKE PETROL ENGINE

BEFORE GETTING STARTED

Thank you for your purchase and use of our products. In order to avoid accidents or injury,
please read this manual carefully before using the machine. After reading, preserve it for

further reference. This manual is a part of the gasoline engine and should be transferred
when the machine is resold.

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 18 of 44

SAFETY LABELS

DANGER

Indicates a hazard, if not avoided, can result in human injury or
death.

WARNING

Indicates a hazard, if not avoided, could result in human injury
and/or property damage.

CAUTION

Indicates a hazard, if not avoided, might result in slight injury
and/or property damage.

Please read and understand this owner’s manual before

operation of the engine to avoid accidents by familiarizing

yourself with your engine’s controls and safe operation

procedures.

SAFETY INSTRUCTIONS

1. Please perform some pre-operation checks before operation to avoid human
injury and equipment damage.

2. Keep the engine in good ventilated places at least 1 meter away from buildings

and other equipment’s during operation and keep the flammable substances

away from the engine to avoid fire.

3. Keep children and pets away from the operation area.

4. Make sure that the person who operates the engine receives proper instruction.

5. Keep the flammable substances (gasoline, matches) away from the operating
engine.

6. As gasoline is extremely flammable and explosive under certain conditions,
please refuel in a well-ventilated area with the engine stopped.

7. Do not fill above the shoulder of the fuel strainer.

8. Make sure the fuel cover is tightened.

9. Make sure that any spilled fuel has been wiped off before starting the engine.

10. Do not smoke or allow flames or sparks where the engine is refueled or where
gasoline is stored.

11. Exhaust contains poisonous carbon monoxide, a colorless and odorless gas.

Breathing exhaust can cause loss of consciousness and may lead to death. Do

not operate the engine without good ventilation or in enclosed room.

12. If you run the engine in an area that is confined, or even partially enclosed, the

air you breathe could contain a dangerous amount of exhaust gas. Provide

adequate ventilation so as to keep exhaust gas from accumulation.

13. Place the engine on flat (level) surface, tilting angle of the engine should not be
more than 20º, otherwise it will lead to fuel spilling out.

14. Do not cover the engine so as to avoid fire occurrence.

15. The muffler becomes very hot during and immediately after operation. Be careful

not to touch the muffler while it is hot. Let the engine cool down before storing the

engine indoor.

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 19 of 44

PRE-OPERATION CHECKS

Check the Oil Level

Lubricating oil:

• Engine lubricant oil is a major factor affecting engine performance and service
life.

• The use of the lubricating oil free of cleaning agent or the lubricating oil for the
two-stroke engine will shorten the life of the gasoline engine.

• The operating temperature range recommended for the gasoline engine is -
5℃~40℃.

• Use 4-stroke motor lubricant oil. 20W-40 is recommended in general, at all
temperature use. Other viscosities shown in the chart may be used when the
average temperature in your area is within the indicated range.

Ambient temperature

• Before checking engine lubricant oil, place the engine on level surface

• Turn out the oil filler cap and clean the dipstick with a clean cloth.

• Insert the dipstick back into the oil filler hole without turning it in.

• If oil level is below the lower mark of the dipstick, fill oil to the upper level of the

dipstick.

• Reinstall the oil filler cap properly.

Upper level

Dipstick

Lower level

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 20 of 44

Engine oil alert system (optional function):

The oil alert system is designed to prevent engine damage caused by insufficient oil in the
crankcase. When the oil level in the crankcase falls below the safe limit, the oil alert
system will automatically stop the engine even if the engine switch remains at the ON
position. If the engine stops and cannot be restarted, check the engine oil level before
troubleshooting in other areas.

(1) Drain plug

(2) Engine switch

(3) Lower level

Fuel Level

• Check the fuel gauge, and refill the tank if the fuel level is low. Do not fill above
the shoulder of the fuel strainer. The fuel 90# gasoline is recommended.

• Unleaded gasoline produces less engine and spark plug fouling and extends
exhaust system life.

• Never use stale or contaminated gasoline or oil/gasoline mixture. Avoid dirt,
rubbish and water from getting into the fuel tank.

• If spark knock or pinging occurs at a steady engine speed under normal load,
change brands of gasoline. If spark knock or pinging persists, see an authorized
dealer.

WARNING:

• Running the engine with persistent spark knock or pinging can cause engine
damage.

• If persistent spark knocks or pinging is caused by improper usage of the unit,
the Distributor’s Limited Warranty does not cover parts damaged by that.

(1) Fuel tank

(2) Fill in hole

(3) Red line level

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 21 of 44

Air Cleaner

The air cleaner is a dry type including paper element and foam element.

• Remove the clip and dismantle the air cleaner housing or remove the wing nuts
and air cleaner cover.

• Wash the element in solution of household detergent and warm water, then
rinse thoroughly, or wash in nonflammable or high flash point solvent. Allow the
element to dry thoroughly

1) Butterfly nut

2) Air cleaner cover

3) Butterfly nut

4) Paper element

5) Foam element

6) Seal washer

7) Silencer plate

WARNING:

Do not run the engine without air cleaner.

DANGER

Using gasoline or flammable solvent to clean the filter element can cause a fire or
explosion.

CAUTION:

Do not run the engine without air cleaner core, otherwise dust and/or other foreign matters
may get into the engine through carburetor, and results in rapid engine worn-out.

STARTING THE ENGINE

• Turn the fuel valve to ON position, unscrew the drain plug on carburetor bottom,
and fasten the drain plug until oil spills out.

• Pull the choke rod to the CLOSE position. Adjust throttle to proper position. Pull
the starter grip lightly until resistance is felt, then pull it rapidly

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 22 of 44

(1) Fuel Valve

(2) Start Level

(3) Drain Plug

NOTE:

• Do not allow the starter grip to snap back against the engine. Return it gently to
prevent damage to the starter.

• Once the engine got started, let it run for 1~3 minutes at idle speed, check
whether it is balanced, cracked, then pull the throttle to open position, adjust
choke rod to OPEN.

(1) Auto-Throttle

(2) Off Position

(3) Starter Knob

Electrical Starting:

Turn the engine switch to START

position and hold a while until the engine

started

ENGINE SWITCH

NOTE: Restrict the starting time within 5 seconds to avoid engine damage. If engine

cannot be started, release starter knob, retry after 10 seconds.

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 23 of 44

STOPPING THE ENGINE

Adjust throttle to proper position. Reduce engine speed, close the choke. Turn engine
switch to OFF position.

(1) Throttle knob

(2) Throttle is at OFF

DANGER:

• Gasoline is extremely flammable and explosive under certain conditions.

• Refuel in well-ventilated places with the engine stopped. Do not smoke or allow

flames or sparks near the places where the engine is refueled or gasoline is
stored.

• Do not add fuel over the shoulder of strainer. After fueling, tighten the tank
cover.

• Fuel vapors are extremely flammable and may ignite after the engine has
started. Make sure that any fuel spillage has been wiped off before starting the
engine.

• Avoid skin coming in contact with gasoline for a long time, avoid breathing in
gasoline vapors. Keep children away from them.

NOTE:

Fuel can damage paint and plastics. Be careful when refueling. Damage caused by
spilling fuel is not covered under warranty.

MAINTENANCE

Do periodic maintenance to keep the engine in good condition. Always follow the
inspection and maintenance recommendation and schedules given in this manual.

WARNING:

Stop the engine before doing any maintenance work. If the engine must be operated,
provide adequate ventilation. Breathing in exhaust can cause loss of consciousness and
even lead to death.

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 24 of 44

Everyday Maintenance:

1. Air cleaner: A dirty air cleaner will restrict air flow into the carburetor. To prevent
carburetor malfunction, service the air cleaner regularly. Service more frequently
when operating the generator in extremely dusty areas.

• Check air cleaner core, get rid of fouling, and keep the core clean.

• Check bolts, fasten the loose ones.

• Check whether lubricant oil level is within the limits.

2. Clean the core after 25hrs of engine run

3. Clean carbon fouling of the spark plug after working up to 50hrs. Check the
clearance, and adjust the gap to 0.6-0.7mm (see figure 4-1). Check radiator, and
clean fouling among radiators.

• Drain the oil while the engine is warm to assure rapid and complete
draining.

• Remove the drain plug and sealing washer, remove the oil filler cap, and
drain the oil.

• Reinstall the drain plug and sealing washer. Tighten the plug securely.

• Refill with the recommended oil and check the oil level.

(1) Dismantle Spark Plug

(2) Adjust Clearance

4. Clean the fuel tank and filter when working time reaches 100hrs: Remove the fuel
cover, drop out filter, and wash it with brush slightly. Remove fuel tank, clean the
fouling and water inside fuel tank. Reinstall fuel tank, place filter from fill-in hole,
filling the clean fuel to red line level.

1) Drain plug

2) Engine switch

3) Lower level

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 25 of 44

Check aging of fuel pipe every 2 years. If ageing, hardening and cracking is detected,
have it replaced. Tighten the joints, and check leakage.
Before storing the unit for an extended period:

1. Make sure the storage area is free of excessive humidity and dust.

2. Service according to the table below.

Storage Time

Recommended Service Procedure To Prevent Hard Starting

Less than 1 month

No preparation required

1 to 2 months

Fill with fresh gasoline and add gasoline conditioner

2 months to 1 year

• Fill with fresh gasoline and add gasoline conditioner

• Drain the carburetor float bowl

• Drain the fuel sediment cup

STORAGE

If the engine is not used for a long time, do the necessary maintenance before its storage.

• Firstly, take off the fuel tank, drain out all fuel, and clean the dirt and water

inside the tank. Open the fuel cock, unscrew the drain plug at the bottom of
carburetor, drain out fuel in carburetor thoroughly, and then tighten the drain
plug.

• Secondly, unscrew the drain plug at the bottom of the crankcase and drain out

the lubricant oil in the crankcase thoroughly, then tighten the drain plug.

• Finally, clean the surface of the engine with clean cloth, remove the dirt and

dust etc. Then store the engine in a well-ventilated, dirt-free place.

TRANSPORTATION

• Contact with the hot engine or exhaust system can cause serious burns or fires.

Allow the engine to cool down before transporting or storing the engine.

• During transport of the engine, turn the engine switch and the fuel valve to OFF.

Keep the engine cool.

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 26 of 44

TROUBLESHOOTING

1. The Engine Can’t Startup

• Have the engine checked if it is hard to or cannot be started.

• Firstly, check the fuel level of the fuel tank. Turn fuel valve to (2), Fuel should

flow from the drain when the fuel valve is turned ON. Tighten the drain plug.
(Refer to starting of the engine)

2. Spark Plug

Check the spark plug. Remove the spark plug cap and clean any dirt around it. If the
engine still cannot be started after repeating several times, please see the authorized
dealer. Users are not allowed to dismantle or reassemble the unit by themselves.

3. Not Enough Power

• Check the air-cleaners. Please refer the maintenance inspection book to clear

the air-cleaner.

• Check the fuel. Please strain out the gasoline in fuel tank and in carburetor, and

fill in new gasoline.

• For any other trouble, please contact our dealer.

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 27 of 44

ENGINE PARTS DIAGRAM & LIST (KK-PE4-103)

CRANKCASE ASSEMBLY

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 28 of 44

Sl No

Part No.

Description

1

1-1

Crankcase

2

1-2

Valve chamber clapboard sub-Assembly

3

1-3

Stud M5×118

4

1-4

Stud M6×52

5

1-5

Oil seal(17×30×6), crankshaft

6

1-6

Cover, oil filter

7

1-7

Gasket-Cover Oil Filter

8

1-8

Return pipe

9

1-9

Flow guard, lower

10

1-10

Sway bar

11

1-11

Keeper, sway bar

12

1-12

Oil seal, sway bar

13

1-13

Washer, sway bar

14

1-14

Bottom plate

15

1-15

Bolt M6×14

16

1-16

Bolt M5×10

17

1-17

Bolt M8×14

18

1-18

Oil Sensor

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 29 of 44

CRANKCASE COVER ASSEMBLY

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 30 of 44

Sl No

Part No.

Description

1

2-1

Set pin φ8×14

2

2-2

Gasket, crankcase

3

2-3

Drain plug

4

2-4

Washer -Drain Plug

5

2-5

Crankcase cover

6

2-6

Oil seal(17×30×6), crankshaft

7

2-7

Dipstick sub-Assembly

8

2-8

OIL Dipstick

9

2-9

Seal, dipstick

10

2-10

Oil plug sub-Assembly

11

2-11

Oil plug

12

2-12

Seal, oil plug

13

2-13

Driven gear sub-Assembly, governor

14

2-14

Driven gear, governor

15

2-15

Sliding sleeve

16

2-16

Flyweight

17

2-17

Governing shaft

18

2-18

Pin, flyweight

19

2-19

Snap ring

20

2-20

Washer, driven gear

21

2-21

Bearing 6203

22

2-22

Bolt M6×29

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 31 of 44

CYLINDER COVER

Sl No.

Part No.

Description

1

3-1

Gasket, cylinder head

2

3-2

Cylinder cover

3

3-3

Spark plug

4

3-4

Bolt M6×35

CRANKSHAFT, PISTON ＆ CONNECTING ROD

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 32 of 44

Sl No.

Part No.

Description

1

4-1

Crankshaft sub-Assembly

2

4-2

Crankshaft

3

4-3

Woodruff key

4

4-4

Connecting rod

5

4-5

Shank

6

4-6

Cap connecting rod

7

4-7

Bolt M5×24

8

4-8

Piston

9

4-9

Piston pin

10

4-10

Circlip, piston pin

11

4-11

Piston ring set

12

4-12

N/A

13

4-13

14

4-14

15

4-15

16

4-16

17

4-17

Timing driving gear

18

4-18

Bearing 6203

19

4-19

Key(pulley) 5x5x35

COMBINATION OF CAMSHAFT & VALVE

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 33 of 44

Sl No.

Part No.

Description

1

5-1

Camshaft

2

5-2

Washer, camshaft

3

5-3

Tappet

4

5-4

Intake valve

5

5-5

Exhaust valve

6

5-6

Oil seal, valve stem

7

5-7

Spring seat, valve

8

5-8

Valve spring

9

5-9

Cap (Valve)

CARBURETOR ASSEMBLY

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 34 of 44

S/N

Part No.

Description

1

6-1

Gasket, intake port

2

6-2

Connecting block

3

6-3

Gasket, carburetor

4

6-4

Carburetor Assembly

5

6-5

Choke lever

6

6-6

Float chamber sub-Assembly

7

6-7

Float chamber

8

6-8

Screw

9

6-9

Seal, screw

12

6-12

Gasket, float chamber

13

6-13

Float sub-Assembly

14

6-14

Needle valve

15

6-15

Mixture chamber body

16

6-16

Main nozzle

17

6-17

Main jet

18

6-18

Throttle unit

19

6-19

Throttle lever

20

6-20

Airproof washer

21

6-21

Washer

22

6-22

Cover

24

6-24

Idle adjusting screw

25

6-25

Screw M4×6

26

6-26

Tubing

27

6-27

Pipe clamp

28

6-28

Oil switch

29

6-29

A mounting block

30

6-30

Bolt M6×14

31

6-31

Nut M6

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 35 of 44

FUEL TANK ASSEMBLY

Sl No.

Part No.

Description

1

7-1

Fuel filler cap sub-Assembly

1.1

7-1.1

Fuel filler cap

1.2

7-1.2

Packing ring

2

7-2

Fuel tank

3

7-3

Fuel Filter(Upper)

4

7-4

Fuel Cock

5

7-5

Fuel Tube 200mm

6

7-6

Nut M6

7

7-7

Pipe clamp

8

7-8

Bolt M4×6

9

7-9

Fuel Tube 130mm

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 36 of 44

AIR CLEANER ASSENBLY

Sl No.

Part No.

Description

1

8-1

Cover, air cleaner

2

8-2

Housing, air cleaner

3

8-3

Foam, air cleaner

4

8-4

Bracket, air cleaner

5

8-5

Gasket, air cleaner

6

8-6

Nut M5

7

8-7

Self-tapping screw ST4×10

MUFFLER

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 37 of 44

Sl No.

Part No.

Description

1

9-1

Gasket, exhaust port

2

9-2

Exhaust muffler

3

9-3

Nut M6

4

9-4

Muffler Protector (Wire Net)

RECOIL STARTER

Sl No.

Part No.

Description

1

10-1

Fan Cover

2

10-2

Recoil starter Assembly

3

10-3

Friction spring

4

10-4

Rope

5

10-5

Shoulder screw

6

10-6

Recoil Spring/Spiral spring

7

10-7

Ratchet

8

10-8

Guide Plate

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 38 of 44

Sl No.

Part No.

Description

9

10-9

Rope Reel

10

10-10

Starter Handle

11

10-11

Starter Cover

12

10-12

N/A

13

10-13

Engine switch

14

10-14

Bolt M6×10

15

10-15

Bolt M6×14

16

10-16

Ratchet Spring

GOVERNING CONTROL SYSTEM

Sl No.

Part No.

Description

1

11-1

Governor arm

2

11-2

Pull-rod, governor

3

11-3

Lock bolt

4

11-4

Return spring

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 39 of 44

Sl No.

Part No.

Description

5

11-5

Assistant spring, governor

6

11-6

Mount, governor

7

11-7

Handle

8

11-8

Positioning plate

9

11-9

Spring, governor

10

11-10

Wave washer

11

11-11

Washer

12

11-12

Supporting plate unit

13

11-13

Pressure plate

14

11-14

Nut M6

15

11-15

Bolt M5×25

16

11-16

Bolt M6×14

17

11-17

Bolt M5×16

FLYWHEEL

Sl No.

Part No.

Description

1

12-1

Fan, flywheel

2

12-2

Starter Sleeve /flange

3

12-3

Flywheel

KisanKraft

®

4-STROKE PETROL ENGINE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 40 of 44

Sl No.

Part No.

Description

4

12-4

Nut M12×1.25

IGNITION COIL

Sl. No.

Part No.

Description

1

13-1

Cap, spark plug

2

13-2

Cable, engine stop

3

13-3

Ignition coil sub-Assembly

4

13-4

Ignition coil

5

13-5

Bolt M6×25

KisanKraft

®

PRODUCT RANGE

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 41 of 44

KisanKraft has a large range of products to serve the farmers. A list of our products
is given below:

Brush Cutters and Accessories

Brush Cutter/Power Weeder
Backpack Brush Cutter
Tea Pruner
Pole pruner with Engine
Reaper Attachment
Blades-Circular
Blades (2 &3 points)
Baffle
Nylon Rope
Tap & Go

Chainsaws

Petrol Chainsaw

Electric Chainsaw
Chain Sharpening Machine

Engines and Water Pumps

Engine –Diesel-(Horizontal)
Engine –Diesel(Vertical)

Engine-Kerosene

Water

Pump

with Petrol Engine

Water Pump with Kerosene Engine
Water Pump with Diesel Engine

Hand Tools

Secateurs

Folding Saw
Garden Rake

Garden Shovel

Hedge Shear

Lopper

Telescopic Hedge Shear
Telescopic Lopping Shear
Tree Pruner

Telescopic Steel Pipe & Fruit Picker Bag

Sheep Shear

Garden Tools

Electric Pressure Washer

Hedge Trimmer
Lawn Mower (Electric, Petrol & Manual)
Leaf Blower

Cultivators and Accessories

Petrol and Diesel

Sprayers and Accessories

Battery Sprayer

Portable Power Sprayer
Trolley Sprayer
Manual Knapsack Sprayer
Manual Pressure Sprayer
Rose Cans
Hose Crimping Machine
HTP Sprayer
HTP Delivery Hose
HTP Hose Reel
HTP Stand

HTP Gun / Lance(Brass Rod

Knapsack Power Sprayer

Mister / Duster / Granuel Spreader

HTP Sprayer Set with Diesel Engine
HTP Sprayer Set with Kerosene Engine

Fogging Machine

Milking Machine

Wood Shredder
Fodder Ensiling Chaff Cutter
Fodder Grinder Chaff Cutter
Fodder Mini Chaff Cutter

Harvester

Maize Sheller
Maize Sheller

+ Dehusker
Maize Combine Harvester
Onion Digger Carlotti Italy
Tea Leaf Harvester
Sugarcane Combine Harvester

Sugarcane Leaf Stripper

Transplanter and Post Hole Digger

Paddy Transplanter (2 & 8 Rows)
Transplanter-Vegetable & Tobacco

Post Hole Digger(4” to 14”Augers)

KisanKraft

®

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 42 of 44

Wide Range of Products for Every Need

For more information give MISSED CALL: 07676065555

Many of our products have BIS: ISI certification.

KisanKraft

®

Warranty Certificate

(KISANKRAFT COPY)

This warranty is null & void, if you fail to register the warranty with

KisanKraft by sending the KisanKraft Copy with dealer’s stamp.

KisanKraft Limited (formerly known as KisanKraft Machine Tools P Ltd)

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 43 of 44

Product

Centrifugal Water
Pump For
Agriculture

KisanKraft
Invoice Date

Brand

KisanKraft

KisanKraft
Invoice No.

Model

 KK-WPP-10
 KK-WPP-15
 KK-WPP-21
 KK-WPP-31
 KK-WPP-2535
 KK-WPP-50080

WARRANTY
PERIOD

6-MONTHS

FOR THE SPECIFIED PERIOD FROM THE

DATE OF SALE OR DELIVERY WHICHEVER IS
EARLIER.

Dealer’s

Invoice Date

Dealer’s Invoice

No.

Buyer’s Info (Name, Address, Phone, etc.):

Dealer’s Stamp (Address, Phone, TIN, etc.):

Buyer’s

Sign

Dealer’s Sign

What is covered: KisanKraft Limited and its manufacturers warrant this product to be
free from defects in material or workmanship. All parts defective in material and
workmanship are covered.
This warranty will only cover defects arising under normal usage.
This warranty is limited to repair or replacement by KisanKraft Limited or its
manufacturers at the premises of Authorized Dealers, of such parts as appear to
KisanKraft or its manufacturers, upon inspection, to be defective in material and/or
workmanship. KisanKraft or its manufacturers make no warranty with respect to trade
accessories not manufactured or sold by them.
What is not covered: The warranty shall become null and void and neither KisanKraft
Limited nor any of its manufacturers, nor its authorized dealers assumes any
responsibility, if the failure was caused by the following:
(1) Operation of product with incorrect fuel or lubricants, (2) Incorrect usage of
machine or misuse, (3) Lack of maintenance, (4) Negligence, (5) Accident or physical
damage, (6) Repairs made by unauthorized parties and/or with unauthorized parts, (7)
Improper set up, adjustments, tampering or altered products

KisanKraft

®

Warranty Certificate

(KISANKRAFT COPY)

This warranty is null & void, if you fail to register the warranty with

KisanKraft by sending the KisanKraft Copy with dealer’s stamp.

KisanKraft Limited (formerly known as KisanKraft Machine Tools P Ltd)

: www.kisankraft.com

: [e-mail]

: +91.80. 22178200

Page 44 of 44

Important: (1) Normal maintenance and adjustments to the product is the
responsibility of the customer. (2) Normal wear and tear is not covered under warranty.
(3) Rubber/plastic parts and consumables such as blades, clutch and clutch-bell,
spark-plugs, nylon line, air-filters, fuel-filters, oil seals etc. are not covered under the
warranty.

No Warranty On Electrical Motor / Electrical Parts / Battery Etc.

Incidental / Consequential Loss: KisanKraft Limited or its manufacturers will not be

liable for general damages, including bodily injuries, or for incidental or consequential
damages including, but not limited to, loss of use, loss of profits, loss of production,
expense of substitute equipment or other commercial loss or damage.
Limitation of Liability: This limited warranty is in lieu of all other express warranties,
obligations, or liabilities. Any implied warranties, obligations or liabilities, including, but
not limited to, any implied warranty of merchantability shall be limited in duration to the
applicable warranty period. Any action for breach of any warranty hereunder,
including, but not limited to, any implied warranty of merchantability must be brought
within the applicable warranty period.
Modifications of Warranty: No agent, representative, dealer, or employee of
KisanKraft Limited or any of its manufacturers has the authority to increase or alter the
obligations of this warranty.
Assignment / Transfer of warranty: The warranty cannot be assigned and shall not
transfer if the product is resold by the first buyer. The above warranties are extended
to the first end user (original purchaser), and no warranty is made, nor authorized to
be made assignable on resale by the first end user.

What you must do to obtain limited warranty service: To obtain performance of
any obligation under this warranty for failure during the applicable warranty period,
deliver the defective product, to the nearest Authorized Dealer. KisanKraft Limited, its
manufacturers and its dealers reserve the right to inspect the claimed defective part(s)
to determine if the malfunction is the result of a defect covered by this warranty. Please
note that the decision of KisanKraft Limited with respect to any warranty claim is final.

Receipt is required for availing warranty services

Jurisdiction: All disputes are subject to Bangalore court’s jurisdiction.

Our

Products

ChainsawsBrush Cutters and AccessoriesHarvesters
Engines and Water PumpsHand Tools

Garden Tools



Cultivators and AccessoriesSprayers and Accessories



Transplanter and Post Hole Digger

Milking Machines