Kirisun Communication PT820001, PT820002 Users Manual

MANDATORY SAFETY INSTRUCTIONSTO INSTALLERS AND USERS

z Use Only manufacturer or dealer supplied antennas.
z Antenna minimum safe distance: 108 cm.
z Antennas used for this transmitter must not exceed an antenna gain of 3 dBi.

The FCC (Federal Communications Commission) has adopted a safety standard for human
exposure to RF energy which is below the OSHA (Occupational Safety and Health Act)
limits.

z Antenna mounting: The antenna supplied by the manufacturer or radio dealer must not be

mounted at a location such that during radio transmission, any person can come closer than
the above indicated minimum safe distance to the antenna (i.e. 108cm).

z To comply with current FCC RF Exposure limitations, the antenna must be installed at or

exceeding the minimum safe distance indicated above, and in accordance with the
requirements to the antenna manufacturer or supplier.

z Vehicle installation: The antenna can be mounted at the center of a vehicle metal roof or

trunk lid if the minimum safe distance is observed.
Antenna substitution: Don’t substitute any antenna for the one supplied or recommended by
the manufacturer or radio dealer. You may be exposing person(s) to excessive radio frequency
radiation. You may contact your radio dealer or the manufacturer for further instructions.
Warning

Maintain a separation distance from the antenna to person(s) at least 108cm.

“This transmitter is authorized to operate with a maximum duty factor of 50%, in a typical
push-to-talk mode, for satisfying FCC RF exposure compliance requirements.”

Caution:
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.

1 of 12 2008-6-2

Operating Instruction of PT8200

Contents

1 Package-opened Inspection and Device................................................................................1

2 Familiarity with the Machine...................................................................................................2

3 Basic Operation .....................................................................................................................4

4 Program Button Function.......................................................................................................4

５Intercom Call .........................................................................................................................6

５.1 Selective Call..............................................................................................................6

５.2 Send Selective Call....................................................................................................6

５.３Receive Selective Call...............................................................................................6

５.４Call Prompt................................................................................................................6

6 Select Group..........................................................................................................................7

7 Talkaround .............................................................................................................................7

8 Applied Items .........................................................................................................................7

9 Scan ...................................................................................................................................8

9.1 Start/Close Scan Function .............................................................................................8

9.2 Cancel Noise Channel...................................................................................................8

9.3 Edit Scan List.................................................................................................................8

9.4 Increase or Cancel the Channels in the Scan List.........................................................8

9.5 Set Priority Channel.......................................................................................................9

10 OST OST.............................................................................................................................9

11 GPS Information View..........................................................................................................9

12 Wired Replication Mode.....................................................................................................10

13 Common Failures and Troubleshooting.............................................................................10

14 Main Specifications............................................................................................................ 11

1 Package-opened Inspection and Device

Please check the host in the package and the supplied accessories in the following table prior to
use of this Machine. Where any articles are found lost or damaged, please contact the local
distributor without delay.

1.1 Supplied Accessories
No. Accessories Quantity

01 Stationary Support 1
02 Power Cable 1
03 Hand Microphone 1
04 Microphone Hanger 1
05 M4*10 Combination Screw 4
06 M4*16 Self-tapping Screw 2
07 M5*16 Self-tapping Screw 4
08 Operating Instruction 1
09 Warranty Card 1

2 of 12 2008-6-2

Stationary Support

Microphone Hanger

１.2 Preparatory Work

1.21 Connection of Power Cable

First of all, please check whether there is a hole for the power cable on the insulating board. If no,
please bore the board with the suitable drill bit and fix a rubber grommet on it.
Afterwards, please have the cable pass through the insulating board and lead from the car into the
car engine. Connect the red conductor to the positive terminal of the accumulator and the black
conductor to the negative terminal.
At last ring the remained conductor and fix it.
Note: Please maintain the sufficient relaxation of the power cable to make it convenient to dismantle
the radio in the state of power connection.

1.22 Fixation of Radio

Warning: For the purpose of passengers’ safety, please fix the radio firmly on the stationary support
so that the radio will not be loosened in case of collision.
1） The stationary support is taken as an example. Draw the position and drill a hole on the

instrument panel first, and then fix the stationary support with 4 M5*16 self-tapping screws.
(Note: please fix the radio at the position convenient for operation an d control, and leave an
enough space for fixation and connection of the cable.)

2） Slide the radio into the stationary support and fix it with 4 M4*10 combination screws (plus plain

washer and spring washer). (Different combinations of fixing holes are selectable to adjust the

radio to the proper height and visual angle.)
3） Connect the antenna and the power cable to the radio.
4） Fix the microphone hanger at the position easy to use, with 2 M4*16 self-tapping screws. (The

microphone and its cable should be fixed at the position not affecting safe driving.)
5） Connect the microphone to the microphone jack on the front panel of the radio and put it on the

hanger.
Note: Where replacement of the protective tube for the power cable is required, please use the one
of the same specification without fail. It is not allowed to change it into the tube of higher capacity.

M4*10 Combination Screw

Power Cable

Hand Microphone

M5*16 / M4*16 Self-tapping

Screw

2．Familiarity with the Machine

2.1 Description of External View

3 of 12 2008-6-2

⑶⑷⑸

⑾

⑴⑵

（1）

⑺

power button

⑼⑽⑹

⑻

Press this button for a long time to start or close the intercom.

（2）LED indicator

The red indicator will light when it transmit the carrier; the green indicator will light when it
receives the carrier.
The indicator will flicker and give the orange light when it receives Dtmf or 2Tone signal
consistent with the set one locally.
The red indicator flickers in the scanning process.

（3）

/ button (programming button)

（4）LCD display screen

For details, see “LCD Display”.

（5）Volume Control knob

To be used to adjust volume.

（6）Microphone/Programming Interface
（7）

button (programming button)

（8） button (programming button)
（9）
（10）

button (programming button)

button (programming button)

（11）PPT button (on the hand microphone)

Press the PTT button first, and then speak to the microphone to transmit the sound to the
other. Please don’t press this button if you want to listen to the other.

2.2 Display Screen

Display Description

It means the receiving signal strength. 4 lines mean the strongest signal.
Transmission power level
”L” means the transmission of signal for the intercom at the lower power;
”M” means the transmission of signal for the intercom at the medium power;
”H” means the transmission of signal for the intercom at the high power;
Receive Call display
The intercom receives a selective call/call reminder.
Monitoring State display

Scanning State display