Kirisun Communication PT650001 User Manual

PT6500 User’s Manual

PT6500

User’s Manual

CONTENTS

■

Unpacking and checking

 Supplied accessories

■ Preparation

◆ Charging the battery

◆ Installing/Removing the battery pack

◆ Installing the antenna

◆ Installing the optional speaker/microphone

◆ Installing the belt clip

■ Getting acquainted

■ Basic Operation

■ Programmable Button functions

■ VOX

■ Copy mode

■ Whole setting

◆ Time-out Timer（TOT）

◆ Battery Saving

◆ Low battery warning

◆ Voice Annunciation of Channel Number

◆ CTCSS/ DCS

■ User’s resolution

◆ Busy Channel Lockout（BCL）

◆ Receiving squelch mode

◆ DTMF signaling

◆ 2TONE signaling

◆ Transmit start/over signaling (PTT ID)

■ Problems and troubleshooting

■ Major Specifications

■ Status setting

Page 1 of 26

PT6500 User’s Manual

A

P

B

y

Charger

Bel

lip

Hand

p

█ Unpacking and checking

Unpack the transceiver carefully. We recommend that you identify the items listed in the following table

before discarding the packing material. If any items are missing or have been damaged during

shipment, please contact the dealer immediately.

Supplied accessories

Item Quantity

Antenna 1

Battery 1

Belt clip 1

Charger 1

Power adapter 1

Hand strap 1

User’s Manual 1

ntenna

ower adapter

t c

atter

stra

Preparation

█

◆Charging the battery

Connect the power adapter with the battery charger. Plug the adapter into an AC wall outlet
and the indicator turns green.

Place the battery or transceiver into the charger slot, and make sure the transceiver has

been turned off.

Make sure the battery is well connected with charger, then the indicator turns red or flashes,

then the charger gets in the state of charging automatically.

Page 2 of 26

PT6500 User’s Manual

When battery is fully charged the indicator turns green.

The performance will be at the best condition if you remove the battery when the green

indicator is on. Then remove the power adaptor from the wall outlet.

The charger will enter the protection mode when the yellow indicator flashes, which means

the temperature or the circuit is abnormal. Do not charge the battery at this moment, just

remove the battery and turn off the power of the charger.

Notes:

The battery is not fully charged in the factory. Before the initial use, please charge the new

*

battery.

* The KB-36A Ni-MH battery/KB-36C Li-ion battery of this company is adaptable with this

machine.

* When you charge the battery the first time or after long time storage (2 months), several

times of charging is needed. Make sure the battery is charged at least once every three

months.

* Do not charge the battery again if it is charged fully or not in the low-pressure warning

mode, otherwise, its life will be shortened or it will be damaged. Remove the battery from

the charger after charging.

* When you use the KB-36A battery, and the transceiver is in the low-pressure warning

mode, recharge the battery before use. Do not power on by force, otherwise, its life will be

shortened or it will be damaged.

* There is a protection circuit in KB-36C battery, so the power will be cut off at too low

battery.

Page 3 of 26

PT6500 User’s Manual

◆Installing/Removing the battery pack

To install the battery pack:

Match the 3 bulges of the battery pack with the corresponding holes at the rear Button of
the transceiver.

To install the battery pack:

Then firmly press the battery pack downwards to lock it in place until a click is heard.

To remove the battery pack:

Use your thumb to press the belt clip, and one side of your index finger to press the release
button; and then pull the battery away from the transceiver.

Notes:

* Do not cause short-circuit or throw the battery to the fire.

Page 4 of 26

PT6500 User’s Manual

* Do not disassemble the battery by your self.

◆Installing the antenna

Screw the antenna into the connector at the top of the transceiver by holding the Button of
the antenna and turn it clockwise until secure.

◆ Installing the optional speaker/microphone

Insert the speaker/microphone plug into the jacks of the versatile connector, and fix it with
the supplied snail screw.

7

◆ Installing the belt clip

Match the grooves of the belt clip with those on the rear of the battery. Then press the

support belt clip downwards to lock it in place. Push the card by inserting your nail or tool

into the groove at the upper part of the clip to remove the belt clip.

Page 5 of 26

PT6500 User’s Manual

 Getting acquainted

D
E

F

G

J

H

I

The functions of the components are as follows:

A. LED Indicator

Lights red while transmitting;

Lights green while receiving a signal.

B. Power/Volume Switch

Turn clockwise till a click is heard to switch on the radio.

CB

A

N

K
L

M

Turn counterclockwise till a click is heard to switch off the radio.

Rotate to adjust the volume after turning on the radio.

C. Channel Selector

Rotate to select the channel 1-128.

D. Antenna

E. Top Button (programmable button)

It is recommended to be set as the emergency warning Button.

F. Side button 1 (programmable button)

G. P TT （PUSH-TO-TALK）:

To make a call, press and hold the PTT button, then speak into the microphone with

Page 6 of 26

PT6500 User’s Manual

normal voice.

H. Side button 2 (programmable button)

I. Button

Return and delete button in the menu.

J. Button

Select Button.

K. Button

Select Button.

L. Button

Enter and Confirm Button.

M.

Numeric keypad

N. Microphone/speaker jacks

For connecting microphone/speaker.

Explanation for the screen

 Basic Operation

1. Switch On

Switch on the radio by turning the Power/Volume switch clockwise

till a click is heard, then the radio will be in the state of stand by

and you will hear a beep if the dealer has set it.

Page 7 of 26

PT6500 User’s Manual

2. Adjust Volume

Press the button preset as canceling squelch to listen to the background noise and rotate

the Power/Volume switch to adjust volume.

3.

Select a Channel

Rotate the channel selector to select channels. You will hear voice from the speaker while

receiving proper signals.

As shown in the above right figure:

Zone 1 is the zone of current channel (8 zones from 0 to 7).

H is the transmit power of the channel, H stands for high power, M for middle power while

L for low power.

CHANNEL 1 is the current channel (128 zones from 1 to 128).

4. Make a Call

Page 8 of 26

PT6500 User’s Manual

O

O

O

O

L

9

High

iddl

O

O

O

Cl

M

Sel

Numb

Sel

S

FRQ

S

FRQ

S

S

pen/close

pen/close

pen/close

To make a call, press PTT, and speak in normal voice and please keep your mouth 3~4

cm away from the microphone.

e
n
u

pen/close

pen/close

pen/close

evel 0-

ose for saving

or 1:1, 1:2, 1:4

low

, m

e,

pen/close

Receive a Call

5.

ect squelch mode

Release the PTT button to receive a call.

ect zone

Your dealer can set CTCSS, DCS, 2 Tone signaling on you radio channels by PC software.

If you select a channel that has been preset with the tone signaling, you will not hear any

et Rx

er list

et Tx

et Rx Ctcss

et Tx Ctcss

other calls except those from your own system.

Operation on menu: press “ ”button to enter the menu or confirm any contents;

6.

press

“ ” button to return to the previous menu or cancel the set. When entered the

menu, select the sub-menu with the “channel selector”, “ “or “ ”.

The menu is as follows:

Page 9 of 26

PT6500 User’s Manual

If can not enter that way, you have to set in PC communications;

Set back light:

1. As shown: in CH 1 , press

2. Press to enter select mode,

3. Press / , and Back Light is shown,

4. Press to select On or Off,

5. Select On or Off with / , press to confirm.

Set the squelch level:

1. As shown: in CH 1 , press

2. Press to enter select mode,

3. Press / , then Squelch Level is shown,

4. Press to select squelch level, e.g., Leve 0

, utilities is shown.

, utilities is shown.

5. Change the squelch level with / , then press to confirm.

Set Companding：

1．As shown: in CH 1 , press

2. Press to enter select mode,

3. Press / , and Companding is shown,

4. Press to select Companding,

5. Select On or Off by / , press to confirm.

Set saving：

1．As shown: in CH 1 , press

, utilities is shown.

, utilities is shown.

2. Press to enter select mode,

Page 10 of 26

PT6500 User’s Manual

3. Press / , and Save is shown,

4. Press to select Save 1：4,

5. Chang the save percentage with / , press to confirm.

Set scrambler：

1．As shown: in CH 1 , press

2. Press to enter select mode,

3. Press / , and Scrambler is shown,

4. Press to select, e.g., Scrambler Off,

5. Select On or Off by / , press to confirm.

Set key tone：

1．As shown: in CH 1 , press

2. Press to enter select mode,

3. Press / , and Key Tone is shown,

4. Press to select Off or On,

, utilities is shown.

, utilities is shown.

5. Select On or Off with / , press to confirm.

Set speak On mode：

1．As shown: in CH 1 , press

2. Press / , and Speak Mode is shown,

3. Press to select the speak on mode,

4. Select with / , press to confirm.

Set call list：

to enter select mode,

Page 11 of 26

PT6500 User’s Manual

1．As shown: in CH 1 , press to enter select mode,

2. Press / , and Call is shown,

3. Press to select the call list,

4. Select with / , press PTT to transmit.

■Programmable Button functions

The dealer can program the 2 Side Buttons and 1 top Button with one of the following auxiliary

functions.

None

Off (“do not set the functions”)

Scan

Separate working

Contact list

Power selector

Show or hide the channel alias

Busy Channel Lockout (BCL)

Key lock

Squelch level selector

Companding

Scrambler

Battery power

Zone

Monitoring

Cancel Squelch

Emergency Alert

Back light

Rptr/Talkarnd

Express select channel 1

Express select channel 2

Call 1, 2, 3 or 4

Channel lock

Adjust display contrast

Page 12 of 26

PT6500 User’s Manual

Notes: programmable key can be set as short key or long key.

The following functions can be programmed by the

dealer:

● None

Set of None。

●

Scan

Press the button set as Scan to start scanning. While in scanning, the radio checks every channel (any

channel in any zone) and stops on the channel on which a signal is detected until that signal disappears.

If the delay time between signal disappearing and continuing scanning has been preset, the radio will

remain on that channel. Only when there are two channels added in the scan list and the scan function

has been activated, the radio can start scanning.

▲ It can be set as: short key: scan, long key：off.

1. Press the programmable key once to start scanning (it should be effective in the channel scan list).

2. Press

Notes: there are 8 zones from 0 (default zone) to 7; and there can be 128 channels to the most in

each zone. There are totally 16 scan lists; you can select any scan list. Every scan list can scan

any channels in different channels (16 channels to the most).

once to quit.

● Separate working

Press the button set as Separate Working to start separate working. This mode is to ensure the safety

of the user while using the transceiver separately.

▲It can be set as: short key: personal working, long key：off.

1. Press the programmable key once to start personal working;

2. Press once again to quit.

Notes: the separate working is connected with the automotive checking in the programming

software, and will be effective when both are set.

● Contact list

Enter the Contact list quickly:

▲ It can be set as: short key: contact list, long key：off.

1. Press the programmable key once to enter the contact list Call

Page 13 of 26

PT6500 User’s Manual

2. Press again to enter the content interface of the contact list, e.g.: Dtmf Call

3. Select the options in the contact list with /

4. Press PTT to transmit

5. Press to quit.

Power select

Rotate the “channel selector” to enter the “power level” menu quickly. There are high, middle and low

levels.

▲ It can be set as: short key: power select, long key：off.

1. Press the programmable key once, will be shown,

2. Press it again,

Zone 0 L

CHANNEL 1

Zone 0 M

CHANNEL 1

3. Press it a third time，

will be shown.

will be shown,

Zone 0 H

CHANNEL 1

●Busy Channel Lockout (BCL)

Busy Channel Lockout can prevent you from interfering other radios that using the same channel.

Press the PTT button when the channel is busy, the radio with BCL function active will make warning

sound and prohibit transmitting. To stop the warning sound, please release the PTT button and the radio

returns to receiving mode.

▲It can be set as: short key: Busy Channel Lockout, long key：off.

1. Press the programmable key once, will be shown,

BCL none

2. Select the character you need with

3、Press

to confirm.

/ , e.g.:

BCL none

BCL carry？

BCL carryPL？

Page 14 of 26

PT6500 User’s Manual

●Key lock

Press the key programmed as “key lock” for one second to lock/unlock the keys for the transceiver.

▲ It can be set as: short key: key lock, long key：off.

1. Press the programmable key once, will be shown,

2. Press it again, will be shown.

CHANNEL

CHANNEL

●Squelch level Selector

Enter the “Select squelch level” instantaneously, 0~9 levels are available with the channel selector.

▲ It can be set as: short key: Select squelch level, long key：off.

1. Press the programmable key once,

will be shown,

2. Select squelch level with

/ , e.g.:

Level 2

Level 3

Level 4

Level 5

3. Press

to confirm.

●Companding

Enter the Companding mode when press the key programmed as “Companding”,

▲ It can be set as: short key: Companding, long key：off.

1. Press the programmable key once to open the Companding mode,

Zone
CHANNEL 1

2. Cancel the mode by pressing it again, will be shown.

will be shown,

Zone

CHANNEL 1

●Scrambler

Press the key programmed as “scrambler” to prevent any third party to hear you talking on the phone.

Page 15 of 26

PT6500 User’s Manual

▲ It can be set as: short key: scrambler, long key：off.

1. Press the programmable key once to open the scrambler mode,

CHANNEL 1

2. Cancel the mode by pressing it again,

will be shown.

will be shown,

CHANNEL 1

●Battery volume checking

Display the battery power.

▲It can be set as: short key: battery power checking, long key：off.

1. Press the programmable key once: the battery power will be shown,

2. Press again: close the display.

● Monitoring

Press the programmed as “monitor trigger” to shut up the CTCSS、DCS、2Tone and DTMF signal, and

you can listen to the signals can not be heard in normal operation, press the key again to return to

normal operation.

▲It can be set as: short key: monitor, long key：off.

1. Press the programmable key once to start monitoring, Moni Moment ON

will be shown,

2. Press again: stop monitoring, Moni Moment OFF will be shown.

●Cancel squelch

Press the key, no matter what the signal or carrier wave is (including optional signal), squelch will be

cancelled.

▲It can be set as: short key: cancel squelch, long key：off.

1. Press the programmable key once to start squelch constantly,

2. If you do not press it, the squelch will still work.

Page 16 of 26

PT6500 User’s Manual

●Emergency Alert

If press the top key programmed as “Emergency Alert”, you can set the warning ring according to the

programming software, or send your identity or background music to your companion or the system.

▲It can be set as: short key: emergency alert, long key：off.

1. Press the programmable key once to start alert,

2. Press it again to stop the alert.

●Back light

Turn on/off the back light.

▲It can be set as: short key: back light, long key：off.

1. Press and hold this key, the back light is on,

2. Release it to recover the normal mode.

●Rptr/Talkarnd

When press the key programmed as “Rptr/Talkarnd”, the next transmission will be at the same

frequency as at which it is received.

▲It can be set as: short key: Rptr/Talkarnd, long key：off.

1. Press the key once, Rptr/Talkarnd will be shown,

2. Press to enter,

3. Press / to select the character you need: e.g.: Repeater Mode or Talkarnd mode,

4. Press to confirm.

●Instantaneously select the channel

Shift to the channel you selected instantaneously, so that you can communicate at the channel you are

used to.

▲It can be set as: short key: instantaneously select channel 1, long key：off.

1. Press the key once to instantaneously select the channel, e.g.：CHANN 15

2. Press again to return.

●Call 1, 2, 3, or 4

Press the side button programmed as Call 1, 2, 3, or 4 to transmit the specified code stored in the

Page 17 of 26

PT6500 User’s Manual

contact list. Release “Call” button, and speak to the microphone to call with the PTT button still

pressed.

▲It can be set as: short key: Call 1, long key：off.

1. Press the key once to make a call(within the current channel), and will quit automatically after the

call.

●Voice Annunciation of Channel Number

Select or delete the voice annunciation function.

●Adjust display contrast

You can adjust the display contrast as per your need.

▲It can be set as: short key: display contrast, long key：off.

1. Press the key once, Contrast will be shown,

2. Press / to select the character you need,

3. Press

to confirm.

●Manual programming

The dealer can open the manual programming rights of:

Channel frequency set, CTCSS，DCS.

Basic operations of programmable keys:

You can set the programmable keys with the “key set” in PC software, as follows:

▲It can be set as: short key: display channel frequency, channel alias and channel No., long key：off.

1. Press the key once, display the channel alias, e.g.:

,

2. Press it again, the channel frequency will be shown, e.g.:

3. Press it a third time，the channel alias will be shown, e.g.:

▲It can be set as: short key: Zone, long key：off.

1. Press the key once, Zone No will be shown,

CHANNEL 1

401.66500

CH 1

2. Select zone No. with / ,

3. Press to confirm.

Page 18 of 26

PT6500 User’s Manual

▲It can be set as: short key: channel lock, long key：off.

1. Press the key once to perform channel lock, then you can not choose the

channel, will be shown.

2. Press it again to cancel channel lock, will be shown.

CHANNEL 1

CHANNEL 1

■ VOX

VOX function enables you to use the radio without manual operations. This function can only be set by

the dealer, and you have to be equipped with the specified earphones.

Before using VOX, you must set VOX gain level. Such setting enables the radio to identify the voice

volume. If the microphone is too sensitive, the background noise will trigger the radio to transmit. If the

microphone is not sensitive enough, it cannot receive your voice when you speak. Make sure to adjust

VOX gain level to proper sensitivity.

■ Auxiliary Functions (programmed with PC)

◆ Time-out Timer (TOT)

TOT timer:

Time-out timer can prevent any caller from occupying one certain channel for an extended period of the

time.

The radio is set with a continuously transmitting limit. If the radio is continuously transmitting longer than

the time preset by the dealer, the radio will stop transmitting and warning

TOT forbidden period:

A period in which the radio is forbidden to transmit after its overtime activity.

During the period, if the PTT key is pressed, there will be a warning tone, and transmitting is forbidden.

TOT pre-warning:

The pre-warning will sound before the TOT action.

After the sound of the warning, the timer will take action when the transmitting time has gone beyond

the limit.

TOT reset:

The time delay from releasing the PTT key to the resetting of the timer is limited.

The countdown will go on if the time after releasing the PTT key is shorter than the reset time.

Page 19 of 26

PT6500 User’s Manual

 Battery Saving

The dealer can set the type of this function by programming.

If the battery saving function is on, 10 seconds after the radio hasn't receive any signals or no operation

is being conducted, the radio enters battery saving mode. When a signal is received or any operation

occurs, it exits battery saving mode automatically.

The types include: 1：1, 1：2, 1：4 and off.

The automatic battery saving function decreases the power consumption.

 Voice Annunciation of Channel Number

The dealer can turn on or turn off this function by programming.

While switching to another channel, you can hear the voice annunciation of the current channel number.

 CTCSS/ DCS

The dealer can set CTCSS/DCS tones on radio channels, which enable you to ignore (not hear) calls

from other irrelevant parties who are using the same channel.

When you receive a signal that has a tone different from the one set on your radio, you will not hear the

signal. Likewise, signals that you transmit will only be received by parties whose CTCSS/DCS tones are

the same as yours.

Note: Using a CTCSS/DCS channel doesn't mean your calls are private. If other parties' CTCSS/DCS

tones are identical with yours, they can hear your calls.

■User’s resolution

Busy Channel Lockout (BCL)

Busy Channel Lockout can prevent you from interfering other radios that using the same channel.

Press the PTT button when the channel is busy, the radio with BCL function active will make warning

sound and prohibit transmitting. To stop the warning sound, please release the PTT button and the radio

returns to receiving mode.

The dealer may provide the following two lock mode:

Carrier wave: it will be locked if there is any Carrier wave;

Carrier wave+ CTCSS/DCS：transmitting is permitted if there are matched CTCSS/DCS in the channel.

 Receiving squelch mode

The dealer may set the condition under which to turn on the speakers:

Page 20 of 26

PT6500 User’s Manual

1. CTCSS/DCS and audio squelch: only when the CTCSS/DCS and optional signaling are patchable.

2. Audio squelch: once the optional signaling is matchable.

3. CTCSS/DCS squelch: when the CTCSS/DCS is matchable.

4. Carrier wave squelch: once there is any Carrier wave.

5. CTCSS/DCS and audio squelch: when the CTCSS/DCS is matchable, or when optional signaling

are matchable.

DTMF signaling

The dealer can set this function by programming.

There are 4 systems of which the parameters can be set, e.g.: group call ID No., * and # sound, etc.

After set a DTMF code in the “code sequence” , select DTMF system in the “DTMF code”, then select

the correspondent DTMF code cable in the “user’s resolution” and transfer it with PTT. Set a DTMF

code in the “deenencoding sequence”, add the sequence into the decoding cable in “DTMF decoding”,

then select the correspondent decoding cable. The dealer may also set the “decoding replay”.

2TONE signaling

The dealer can set this function by programming.

There are 4 systems of which the parameters can be set, e.g.: the duration of the first and the second

tone, the duration of the long tone and audio spacing, etc. Select the audio frequency（3106.0～

288.0hz step size 0.1hz）in “encoding sequence”, and whether the tones sent are long or two tones,

select 2TONE system in “2TONE List”, then select the correspondent 2TONE code cable in the “user’s

resolution” and transfer it with PTT. Select the audio frequency（3106.0～288.0hz step size 0.1hz）in

“decoding sequence”, and whether the tones received are long or two tones, then select the

correspondent decoding cable in the “user’s resolution”. The dealer may also set the “decoding

replay”.

 Transmit start/over signaling (PTT ID)

The identify signal of transmit start/over are used to maintain or disconnect some repeaters or phone

system.

“Transmit start” is used to connect routine repeaters and auxiliary facilities. If the ID transmitted is

matchable with that of the repeaters, the repeaters and auxiliary facilities are available.

“Transmit over” is used to disconnect routine repeaters and auxiliary facilities. If the ID transmitted is

matchable with that of the repeaters, the repeaters and auxiliary facilities are disconnected.

Page 21 of 26

PT6500 User’s Manual

■ Problems and troubleshooting

No. Problems Solution

1 No display

after switched on.

Phase locked loop

2

unlocked （ with “tick,
tick” ）

A．Battery power may be insufficient. Recharge or replace the

battery pack.

B．The power switch may be broken, replace the switch.

C．CPU may be broken, replace the IC.

D．Regulator tube Q45 may be broken，replace the IC.

A．Phase locked loop Crystal Oscillator X1 may be broken,

replace it.

B．Oscillator tube may be broken, replace it.

C．Phase locked loop IC2 may be broken，replace the IC.

3 Cannot transmit.

4 No signal

5 The transmitting red

light is on, but no

voice is heard

6 Receiving green light

is on, but no voice is

heard

A． The frequencies of both users are not the same, select the

same frequency channel again.

B．The CTCSS/DCS signaling of both users are not the same,

set it with PC.

C．Beyond the efficient communication range.

A．Make sure the antenna is well connected.

B．Low sensibility, trimming “computer test mode”。

C．HF amplifier may be broken, replace it.

D．The squelch level is too high, which makes the squelch

E．Mixer tube Q19 may be broken, replace the tube.

F．Frequency Modulation IC4 may be broken, replace the IC.

A．Power-amplifier tube, no power output, replace the tube.

B．Replace the microphone if it is broken.

C．Operational Amplifier IC14 may be broken, replace it.

A．Replace the speaker if it is broken.

B．Audio power amplifier IC9 may be broken, replace it.

C．Switch Tube Q48 may be broken, replace it.

unable to switch on, reset it by PC.

7 Abnormal

programming

D．Operational Amplifier IC6 may be broken, replace it..

A．Make sure the wires are well connected.

B．Abnormal output of the RS-232 serial port of the computer,

check the computer .

Page 22 of 26

PT6500 User’s Manual

C．Abnormal connection of MIC and SPK jack, check the jack.

■ Major Specifications

General specification

Model PT6500

(1) (136 ~ 174) MHz Frequency

Modulation

Number of

Channels
Channel Spacing

MF
Working Voltage

Working

Temperature

Antenna
Microphone

Impedance

Battery (Standard)

Model

Dimensions

Weight

16KФF3E/11KФF3E

128

25 kHz/12.5kHz

1st MF：51.65MHz 2

7.5V cathode Grounding

-25~ +55

50Ω

2.2kΩ

Model：KB-36C，li-ion battery DC 7.4V , 1750mAh

time of use：8 hours （5：5：90 period）

56X120X35mm

413（with battery and antenna）

nd

MF：450kHz

■ Status setting (by the dealer)

Model：___________ Serial No.： _____________

a) Channel setting：

Channel

No.

10

11

Receiving

frequency

1

2

3

4

5

6

7

8

9

Transmitting

frequency

CTCSS/DCS

decoding

CTCSS/DCS

encoding

Power

Band

width

Scannin

g

BCL

Page 23 of 26

PT6500 User’s Manual

12

13

14

15

16

17

18

---

128

b) Optional function：

2．1 Time-out timer（T

OT）：

15——600 s

2．2 Squelch level：

1——9

2．3 Voice annunciation：

On □ Off □ 2．4 Battery saving：

Off □ 1：1 □ 1：2 □ 1：4 □

c) A

uxiliary functions button setting:

Top button

None

Voice reporting selector

Rptr/Talkarnd

Call1/2/3/4

Separate working

Emergency alert

Cancel emergency alert

Rewind

Scanning

High/low power shift

Squelch level adjuster

Monitoring open/Cancel

Squelch open/Cancel

Lock key

□ □

□ □

□

□

□

□

□

□

□

□

□

□

□

□

Side button1

None

Voice reporting selector

Rptr/Talkarnd

Call1/2/3/4

Separate working

Rewind

Scanning

High/low power shift

Squelch level adjuster

Monitoring open/Cancel

Squelch open/Cancel

Lock key

□ □

□ □

□

□

□

□

□

□

□

□

□

□

Companding

Scrambler

Battery volume

□

□

□

Companding

Scrambler

Battery volume

□

□

□

Page 24 of 26

Side button2

None

Voice reporting selector

Rptr/Talkarnd

Call1/2/3/4

Separate working

Rewind

Scanning

High/low power shift

Squelch level adjuster

Monitoring open/Cancel

Squelch open/Cancel

Lock key

Companding

Scrambler

Battery volume

PT6500 User’s Manual

□ □

□ □

□

□

□

□

□

□

□

□

□

□

□

□

□

Page 25 of 26

PT6500 User’s Manual

FCC Requirements

Your radio must be properly licensed Federal Communications Commission prior to user. Your wireless

dealer can assist you in meeting these requirements. Your dealer will program each radio with your

authorized frequencies, signaling codes, etc., and will be there to meet your communications needs as your

system expands.

Compliance with RF Energy Exposure Standards

The two-way radio is designed and tested to comply with a number of national and international standards

and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy. This

radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure

environment at duty cycles of up to 50% talk - 50% listen and should be used for occupational use only. In

terms of measuring RF energy for compliance with the FCC exposure guidelines, your radio radiates

measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in

standby mode.

Note: The approved batteries supplied with this radio are rated for a 5-5-90 duty cycle (5% talk - 5% listen -

90% standby), even though this radio complies with the FCC occupational RF exposure limits at duty cycles

of up to 50% talk.

Complies with the following of RF energy exposure standards and

guidelines

United States Federal Communications Commission, Code of Federal Regulations; 47 CFR part 2 sub-part

J

American National Standards Institute (ANSI) /Institute of Electrical and Electronic Engineers (IEEE) C95.1

-1992

Institute of Electrical and Electronic Engineers (IEEE) C95.1 -1999 Edition International Commission on

Non-Ionizing Radiation Protection (ICNIRP) 1998
Operational Instructions

To ensure optimal performance and compliance with the occupational / controlled environment RF energy

exposure limits in the above standards and guidelines, users should transmit no more than 50% of the time

and always adhere to the following procedures:
Hand-held radio operation

Hold the radio in a vertical position with the microphone 5 cm away from the lips and let the antenna farther

away from your head.

Notices to the User

* Government law prohibits the operation of unlicensed radio transmitters within the territories under

government control.
* Illegal operation in punishable by fine or imprisonment or both.
* Refer service to qualified technicians only.

:

Warning:

This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:

Page 26 of 26

PT6500 User’s Manual

(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the
party responsible for compliance will void the user’s authority to
operate the equipment. Any change to the equipment will void FCC grant.
This equipment has been tested and found to comply with the limits
for a Class B digital device,pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed
used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.
The equipment compliance with FCC radiation exposure limit set forth for
uncontrolled Environment

Page 27 of 26