KIP C7800 Hardware Operation Manual

DIGITAL COLOR PRINTER

KIP C7800

Hardware Operation Guide

Version A.0

- Please read this Hardware Operation Guide
before using the printer.

- Please keep this Hardware Operation Guide
for future reference.

KATSURAGAWA ELECTRIC CO., LTD.

(1)

Thank you for purchasing the DIGITAL COLOR PRINTER KIP C7800.
This Hardware Operation Guide contains functional and operational explanations for the KIP C7800.

Please read this Hardware Operation Guide carefully before using the Printer.
Please keep this Hardware Operation Guide for future reference.

When this machine is installed in U.S.A.
This equipment satisfies the requirements in Part 15 of FCC Rules for a Class A computing device.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.

When this machine is installed in Europe
This equipment satisfies the requirements in Pub.22 of CISPR Rules for a Classic A computing
device.
Operation of this equipment in a residential area may cause unacceptable interference to radio and TV
reception requiring the operator to take whatever steps are necessary to correct the interference.

Do not install this machine around electronic equipment or precision instruments.
Other devices may be affected by electrical noise during operation.

If Machine is installed near other electronic equipment, such as a TV or a radio, interference
to said equipment, such as noise or flickering, may occur.
Use a separate power line and install the PRINTER as far as possible from said equipment.

The International

ENERGY STAR ® Office Equipment Program is an international program that

promotes energy saving through the penetration of energy efficient computers and other office
equipment. The program backs the development and dissemination of products with functions that
effectively reduce energy consumption. It is an open system in which business proprietors can
participate voluntarily. The targeted products are office equipment such as computers, monitors,
printers, facsimiles, copiers, scanners, and multifunction devices. Their standards and logos are
uniform among participating nations.

The symbol shown indicates that this product conforms to
SJ/T11364-2006 of People’s Republic of China Electronic
Industry Standard and does not apply to countries outside of
People’s Republic of China.

The symbol shown indicates that this product conforms to GB
18455-2001 11364-2006 of National Standard of the People’s
Republic of China and does not apply to countries outside of
People’s Republic of China.

KIP C7800 is an ENERGY STAR qualified printer.

The symbol shown indicates that this product conforms to Directive
2002/96/EC of the European Parliament and the council of 27 January
2003 on waste electrical and electronic equipment (WEEE) and does not
apply to countries outside of EU.

Chapter 1 Before Use

1-2

1. 1 Installation Requirements

The following conditions are required for installation of the equipment.
(1) Power source should be as follows (according to your region).

U.S.A. / Europe 220 to 240V (+6% to -10%), 20A or higher, and 50/60Hz
(2) The equipment must be on an exclusive circuit.
The outlet must be near the equipment and easy accessible.
(3) Make sure to connect this equipment to a grounded outlet.
(4) The site temperature range = 15 to 27 degrees centigrade, with the humidity between 20% to
70% RH (NON CONDENSING).
Keep the equipment away from water sources, boilers, humidifiers or refrigerators.
(5) The installation site must not have open flames, dust or ammonia gases.
(6) The equipment should not be exposed to the direct sunlight.
Please draw curtains to block any sunlight.
(7) Ozone will be generated while this equipment is in use, although the quantity generated is
within safe levels. (see certifications)
Ventilate the room, if required.
(8) Levelling Bolts on the bottom of the KIP C7800 should touch the floor correctly.
And the equipment must be levelled.
Floor strength must be ample to sustain the weight of the equipment.
(9) Keep ample room around the equipment to ensure comfortable operation.
Required space is noted.

120cm (48”)
or wider

150cm (59”) or wider

65cm (26”)
or wider

Rear

Front

206cm (81”) or wider
(When optional Auto Stacker is
used.)

187cm (74”) or wider
(When accessory Tray is used)