KIP 720 User Manual
KIP 720 User Manual
Ver. A.1
(1)
Thank you for purchasing KIP 720.
This USER'S GUIDE contains functional and operational explanations for KIP 720.
Please read this USER'S GUIDE carefully before using KIP 720.
Please keep this USER'S GUIDE for future reference.
Installed in USA
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
Installed in Europe
This equipment complies with the requirements in Pub.22 of CISPR Rules for a Class A
computing device.
Operation of this equipment in a residential area may cause unacceptable interference to radio
and TV reception requiring the operator to take whatever steps are necessary to correct the
interference.
Warning
This is a class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Do not install the Machine around other electric equipment or precision instruments.
This may be affected by electrical noise or vibration during operation.
If the Machine is installed near other electric equipment, such as TV or radio, interference to
said equipment, such as noise or flickering may occur.
Use a separate power line and install the Machine as far as possible from said equipment.
The International
ENERGY STAR ® Office Equipment Program is an international program that
promotes energy saving through the penetration of energy efficient computers and other office
equipment. The program backs the development and dissemination of products with functions that
effectively reduce energy consumption. It is an open system in which business proprietors can
participate voluntarily. The targeted products are office equipment such as computers, monitors,
printers, facsimiles, copiers, scanners, and multifunction devices. Their standards and logos are
uniform among participating nations.
As an ENERGY STAR ® Partner, Katsuragawa Electric Co., Ltd. has determined
that this product meets the
ENERGY STAR ® guidelines for energy efficiency.
The symbol shown indicates that this product conforms to Directive
2002/96/EC of the European Parliament and the council of 27
January 2003 on waste electrical and electronic equipment (WEEE)
and does not apply to countries outside of EU.
NOTE
KIP 720 should be connected with a supported KIP printer or a PC with KIP software installed
through a USB cable for any operation. KIP 720 does not operate as a single unit.
The symbol shown indicates that this product conforms to
SJ/T11364-2006 of People’s Republic of China Electronic
Industry Standard and does not apply to countries outside of
People’s Republic of China.
The symbol shown indicates that this product conforms to GB
18455-2001 11364-2006 of National Standard of the People’s
Republic of China and does not apply to countries outside of
People’s Republic of China.
(2)
Safety Warnings
The following warnings are very important in order to safely use this machine.
These notes are important in preventing danger to the operator or operation of the product.
The following symbols are found throughout the document and have the following meaning:
WARNING
This WARNING mark means that th ere is a po ssibility of death or serio us
injury if you ignore or do not follow the said instruction.
CAUTION
This CAUTION mark means that th ere is a possibility of injury or physi cal
damage if you ignore or do not follow the said instruction.
When marked with this symbol, “DO NOT ATTEMPT”
When marked with this symbol, “pay close attention to”
(3)
WARNING
1. The power source should be as follows:
100 - 240VAC, 50/60Hz, 0.5A or higher
2. Use a circuit with a dedicated breaker.
3. Install the machine as close to the wall outlet as possible.
4. If you want to move the machine, contact your service personnel.
Ground the machine with a correct ground source or you may be
electrically shocked.
1. Do not plug in the machine into a multi-wire connector in which some
other equipment is plugged into.
It may cause a fire due to outlet overheating.
2. Do not damage the power cord by stepping on or placing heavy objects
on it.
If the power cord is damaged, it may cause a fire or you may receive an
electrical shock. REPLACE THE CORD IF DAMAGED!
1. Do not put a flower vase, a flowerpot or any water-filled objects on the
machine.
Spilt water could cause a fire or an electrical shock.
2. If the machine generates an unusual smell or noise, turn it off and
unplug it from the wall electrical outlet immediately.
1. Do not remove the screw and do not open the cover if not said to do so
in this User’s Manual. If you ignore this warning, you may be burnt or
receive an electrical shock due to a hot part or electrically charged part
inside.
2. Do not disassemble or tamper with the machine.
It may result in a fire or an electrical shock.
Be sure to catch the plug when you unplug the machine.
Otherwise, you may damage the power cord and may result in a fire or an
electrical shock.
(4)
CAUTION
Do not install the machine in a humidified room or a dusty room.
Also, do not install the machine on an unstable floor as injuries may occur.
1. Unplug the machine before you move it.
The power cord may damage and it may result in a fire or an electrical
shock.
2. If you do not use the machine for a long duration (holidays, company
shutdown) turn off and unplug the printer from the outlet for safety.
Be careful not to catch a finger in the Top Cover.
This product is not intended for use in the immediate visual field on the
display work place. To avoid disturbing reflections on the display work
place this product shall not be placed in the immediate field of vision.
(5)
POWER CORD INSTRUCTION
The Power Cord is necessary for with rating 125VAC or 250VAC more than 3A and use the thing
which was equal to the standard of the specifications country.
The installation of (or exchange to) a power plug which fits in the wall outlet of the installation
location shall be conducted in accordance with the following:
Select a power plug which meets the following criteria;
- The plug has a voltage and current rating appropriate for the product’s rating marked on
its name plate.
- The plug meets regulatory requirements for the area.
- The plug is provided with a grounding pin or terminal.
If the appropriate plug does not fit the wall outlet in the installation, the customer shall install an
appropriate outlet.
Connector Type:
Configuration Standard Rating Usually found in
IEC60320:C13 10A 250V (IEC)
15A 125V (UL)
Plug Type: Model Rating 220-240V
Configuration Standard Rating Usually found in
CEE7/7 16A 250V European countries
KS C 8305 16A 250V Korea
AS/NZS 3112 10A 250V Australia
New Zealand
GB1002
GB2099.1
10A 250V China
IRAM 2073 10A 250V Argentina
BS 1363 13A 250V United Kingdom
SASO 2203 13A 250V Saudi Arabia
BS 546A
IS-1293
SABS-1293
16A 250V India
South Africa
Plug Type: Model Rating 120V
Configuration Standard Rating Usually found in
NEMA5-15 15A 250V United States
Canada
*cord set: less than
4.5m and UL-Listed
WARNING
Chapter 1 Before Use 1-1
Chapter 1
Before Use
page
1. 1 Installation Requirements 1- 2
1. 2 Originals Prohibited from Duplication 1- 3
1. 3 Features 1- 4
1. 4 Specifications 1- 5
1. 5 Appearance 1- 7
1. 6 Specifications for Scan Original 1-10
Chapter 1 Before Use 1-2
1. 1 Installation Requirements
The following conditions have to be satisfied when installing KIP 720 Scanner.
1. Satisfy the following input power condition.
Voltage 100 - 240VAC
Current 0.5A or higher
Frequency 50 / 60Hz.
KIP 720 can be supplied with any voltage within 100 to 240VAC. If the voltage is within this
range, please connect to the outlet simply. (No setting has to be changed.)
2. Make sure to connect the power plug to the outlet that is provided with the Ground Terminal.
3. To completely disconnect the machine from the power source, draw the power plug from the
outlet.
The outlet must be easily accessible near the equipment.
4. The temperature must be within the range from 10 to 32 degrees centigrade, and the humidity
must be 15 to 85% RH.
5. Prevent the machine away from water, fire, dust or direct sunlight.
If it is impossible to avoid the direct sunlight, please pull the curtain to intercept the sunlight.
6. The floor must be enough strong to withstand machine’s weight (About 25kg (55lbs)).
7. Keep enough space around the machine as follows.
(The following values are the least requirements. Please keep a wider space if possible.)
KIP 720
[Rear]
[Front]
(300mm) or wider
w/ Original Tray
(600mm) or wider
for inserting an original
(50mm) or wider
(300mm) or wider
Chapter 1 Before Use 1-3
1. 2 Originals Prohibited from Duplication
It is not necessarily allowed to copy every kind of original.
You may be punished by the law if only you possess the copy of some kind of original.
We recommend you to consider enough before you copy such original.
[Originals prohibited from copying by the law]
1. It is not allowed to copy Currency (Bill, Money, Bank Note, etc.); Government issued
Negotiable Instruments (National Bonds, Security, Local Debt Bonds, etc.).
2. It is not allowed to copy Foreign Currency or Foreign Negotiable Instruments.
3. It is not allowed to copy unused postal stamps or government postcards without permission
to make replica from Government,
4. It is not allowed to copy Government issued revenue stamps, certificate stamps which are
prescribed by Liquor Tax Act or the Commodity Tax Act.
[Special items to be cared]
1. It is warned by the government to copy private issued securities (stock certificate, draft,
check, goods ticket, etc.), commutation ticket or book of tickets, excluding that some specific
company copies such originals as many as it requires for its own business.
2. We recommend you not to copy freely such originals as government issued passport, public
or private issued licenses, automobile inspection certification, Ids and tickets like pass or
meal.
Reference Law Prohibited items to copy
Regulations to control fake currency and
Bond.
Currency (Bill, Money, Bank Note, etc.),
Government issued Negotiable Instruments
(National Bonds, Security, Local Debt Bonds,
etc.)
Control Law against Forged & faked
Foreign Currency, Bill, Bank Note and Bond
Foreign Currency or Foreign Negotiable
Instruments
Forged postal stamps control law Unused postal stamps or government postcards
Forged revenue stamps control law Government issued revenue stamps, and
certificate stamps prescribed by Liquor Tax Act
or Commodity Tax Act
Currency similarity securities Control Law Private issued securities (stock, draft, check,
goods ticket, etc.), commutation or book tickets
[Originals protected by the copyright]
It is prohibited to copy such originals as book, music, paintings, printed copy, maps, drawings,
movie and pictures which are protected by the copyright, except for personnel or family use or
similar purpose.
Chapter 1 Before Use 1-4
1. 3 Features
The KIP 720 has the following features.
Wide format image scanner
KIP 720 is available for various sized originals.
210 - 914.4 mm (8.5 - 36”) in width
210mm (8.5”) - 6,000mm in length.
High speed scanning
KIP 720 provides quick scan operation (65mm/s in monochrome / grayscale, 22mm/s in color on
600 dpi).
High resolution scanner head
KIP 720’s 600dpi CIS enables clear and high quality color / monochrome images.
Space-saving
KIP 720 is a small footprint component to fit on most of your preferred space.
Energy-saving
KIP 720 has Auto Power OFF feature for reduced power consumption.
Chapter 1 Before Use 1-5
1. 4 Specifications
Model KIP 720
Scanning method Sheet through type
Reading sensor Contact Image Sensor
(for A4 size x 5 pieces in staggered arrangement)
Light source LED (R/G/B)
Setting Face up
Starting point of scan Center
Original size Max. : 970.0mm
Min. : 150.0mm
Thickness : 0.05mm to 1.60mm
(Image quality for an original with 0.25mm or thicker is
guaranteed only in a standard size even the scanner
physically accepts it.)
Scanning Width Max. : 914.0mm (36”)
Min. : 210.0mm (8.5”)
Scanning Length Max. : 25m
(Image quality for an original over 6,000mm in length is
not guaranteed)
Min. : 210.0mm (8.5”)
Start point of reading within 0.5mm at Leading Edge
Color mode Monochrome : Binary
Grayscale : 8 bit
Color : 24 bit
Scanning speed
(600 dpi)
Monochrome : 65mm/s
Grayscale : 65mm/s
Color : 22mm/s
Resolution 600dpi
Interface USB 2.0 (Maximum: 5VDC)
Input power Voltage: 100-240VAC
Current: 0.5A (at 100V)
Frequency: 50/60Hz
Power consumption 50W maximum
Environmental conditions 10-32 degrees centigrade, 15-85%RH (Non condensing)
Acoustic noise 60 db or less (during 65mm/s scan operation)
Maschinenlärminformations-Verordnung 3. GPSGV:
Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger
gemäß EN ISO 7779
Outer dimension 1,140mm (Width) x 362mm (Depth) x 162mm (Height)
Weight Approximately 25kg
NOTE
These specifications are subject to change without notice.
NOTE
KIP 720 accepts the inlet voltages of 100 to 240VAC without
additional voltage transformation.
Chapter 1 Before Use 1-6
1. 5 Appearance
No. Part Name Function
1 Upper Unit Reads original images.
To be opened for cleaning / removing original jam.
2 Original Tray Receives an ejected original.
3 Original Table Used to place an original.
4 Original Guide Guides an original to the scanner straight.
5 Main Power Switch Turns on / off KIP 720.
6 Start Button Starts scanning if the controlling software requires user
intervention.
7 Stop Button While scanning: emergency stop
At Standby position: eject
8 LED Indicator green: Ready
green to-and-fro: Scanning
red: Error
red flashing: Cover Open, Jam
6
7
5
1
2 3
4
4
8
Chapter 1 Before Use 1-7
No. Part Name Function
9 USB Terminal Connect a USB cable from the controller PC or a KIP Printer.
(Maximum: 5VDC)
10 AC Inlet Connect a power cord.
9 10
Loading...