KIP 7170K User Manual
KIP 7170K User Manual
Version A.1
Thank you for purchasing the Multi-Function Printer KIP 7170.
This Hardware Operation Guide contains functional and operational explanations for the KIP 7170.
Please read this Hardware Operation Guide carefully before using the printer.
Please keep this Hardware Operation Guide for future reference.
1. When this product is installed in North America.
This product complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This product may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the product.
Note: This product has been tested and found to comply with the limits for a Class A digital
equipment, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the product is operated in a
commercial environment. This product generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual,, may cause
harmful interference to radio communications. Operation of this product in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
This product complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this product may not cause
interference, and (2) this product must accept any interference, including interference that may
cause undesired operation of this product.
Le présent appareil est conforme aux la partie 15 des règles de la FCC et CNR d’Industrie
Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes : (1) I’appareil ne doit pas produire de brouillage, et (2) I’utilisateur
de I’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en comprometter le fonctionnement.
Contains FCC ID: VP8-13551 Contains IC: 7391A-13551
2. When this product is installed in Europe
This product complies with the requirements in CISPR 22 for a Class A computing equipment.
Operation of this product in a residential area may cause unacceptable interference to radio
and TV reception requiring the operator to take whatever steps are necessary to correct the
interference.
Do not install product around other electronic equipment or other precision instruments.
Other equipment may be effected by electrical noise during operation.
If the product is installed near other electronic equipment, such as a TV or a radio,
interference to said equipment, such as noise or flickering, may occur.
Use a separate power line and install the PRINTER as far as possible from said equipment.
(1)
KIP 7170 is an ENERGY STAR qualified multifunction equipment.
The International
promotes energy saving through the penetration of energy efficient computers and other office
equipment. The program backs the development and dissemination of equipment with functions
that effectively reduce energy consumption. It is an open system in which business proprietors can
participate voluntarily. The targeted products are office equipment such as computers, monitors,
printers, facsimiles, copiers, scanners, and multifunction devices. Their standards and logos are
uniform among participating nations.
The symbol shown indicates that this product conforms to Directive
2012/19/EU of the European Parliament and the council of 4 Juiy
2012 on waste electrical and electronic equipment (WEEE) and does not
apply to countries outside of EU.
The symbol shown indicates that this product conforms to
SJ/T11364-2006 of People’s Republic of China Electronic
Industry Standard and does not apply to countries outside of
People’s Republic of China.
The symbol shown indicates that this product conforms to GB
18455-2001 11364-2006 of National Standard of the People’s
Republic of China and does not apply to countries outside of
People’s Republic of China.
The product shown with available options. May vary from the actual product.
ENERGY STAR ® Office Equipment Program is an international program that
(2)
Safety Warnings
The following warnings are very important in order to safely use this product.
These notes are important in preventing danger to the operator or operation of the printer.
The following symbols are found throughout the USER’S Manual and have the following meaning:
WARNING
This WARNING mark means that there is a possibility of death or serious
injury if you ignore or do not follow the said instruction.
CAUTION
This CAUTION mark means that there is a possibility of injury or physical
damage if you ignore or do not follow the said instruction.
When marked with this symbol, “DO NOT ATTEMPT”
When marked with this symbol, “pay close attention to”
(3)
WARNING
Ground the product with a correct ground source or you may be electrically
shocked.
1. The Power source should be as follows:
In U.S.A. : 120V plus/minus10%, 50/60Hz, 15A or higher
In Europe : 220-240V plus6% or minus10%, 50/60Hz, 10A or higher
2. Use a circuit with a dedicated breaker.
3. Install the product as close to the wall outlet as possible.
4. If you wish to move the printer, please contact your service personnel.
1. Do not remove the screw and do not open the cover if not instructed to
do so in this User’s Manual. If you ignore this warning, you may be burnt
or receive an electric shock due to a hot item or electrically charged part
inside of the printer.
2. Do not disassemble or tamper with the printer.
It may result in a fire or an electrical shock.
1. Do not plug in the printer into a multi-wire connector in which some other
equipment is plugged into.
It may cause a fire due to outlet overheating.
2. Do not damage the Power Cord by stepping on or placing heavy items
on it.
If the Power Cord is damaged, it may cause a fire or you may receive
an electric shock. REPLACE THE CORD IF DAMAGED!
1. Do not put a flower vase, a flowerpot or any water-filled item on the
product.
Spilt water could cause a fire or an electric shock.
2. If the product generates an abnormal smell or noise, turn it off and
unplug it from the wall electrical outlet immediately.
Do not throw the toner into a fire or other sources of heat, as it can
explode.
(4)
CAUTION
Do not install the printer in a humidified room or a dusty room.
Also, do not install the printer on an unstable floor as injuries may occur.
1. Unplug the printer before you move it.
The power cord may be damaged and it may result in a fire or electric
shock.
Do not pull the cord when you unplug the printer as you may damage the
Power Cord.
There are hot items inside of the printer.
Take great care not to touch these items when you remove mis-fed media.
Ventilate the room well if you print in a small area.
2. If you do not use the printer for a long duration (holidays, company
shutdown) turn off and unplug the printer from the outlet for safety.
(5)
POWER CORD INSTRUCTION
The installation of (or exchange to) a power plug which fits in the wall outlet of the
installation location shall be conducted in accordance with the following:
WARNING
Select a power plug which meets the following criteria;
- The plug has a voltage and current rating appropriate for the product’s rating
marked on its name plate.
- The plug meets regulatory requirements for the area.
- The plug is provided with a grounding pin or terminal.
If the appropriate plug does not fit the wall outlet in the installation, the customer shall
install an appropriate outlet.
Connector Type:
Configuration Standard Rating Usually found in
IEC60320:C13 10A 250V (IEC)
15A 125V (UL)
Plug Type: Model Rating 220-240V
Configuration Standard Rating Usually found in
CEE7/7 10A 250V European countries
KS C 8305 10A 250V Korea
AS/NZS 3112 10A 250V Australia
New Zealand
GB1002
GB2099.1
10A 250V China
IRAM 2073 10A 250V Argentina
BS 1363 10A 250V United Kingdom
SASO 2203 10A 250V Saudi Arabia
BS 546A
15A 250V United Kingdom
IS-1293
SABS-1293
SEV 1011 10A 250V Switzerland
(6)
India
South Africa
Chapter 1
Before Use
page
1. 1 Installation Requirements 1- 2
1. 2 Originals Prohibited from Duplication 1- 3
1. 3 Features 1- 4
1. 4 Specifications 1- 5
1. 4. 1 General 1- 5
1. 4. 2 Printer part 1- 6
1. 4. 3 Scanner part 1- 8
1. 5 Appearance 1- 9
1. 5. 1 Front view 1- 9
1. 5. 2 Rear view 1-10
1. 6 Specifications for Scan Original 1-11
1. 6. 1 Original - Standard 1-11
1. 6. 2 Special Documents 1-11
1. 6. 3 “Do Not Scan” Originals 1-12
1. 7 Specifications for the Printing Media 1-15
1. 7. 1 Papers not available to use 1-15
1. 7. 2 Keeping the paper in the custody 1-16
1. 7. 3 Treatment against environmental condition 1-17
Chapter 1 Before Use 1-1
1. 1 Installation Requirements
The following conditions are required for installation of the equipment.
1. POWER SOURCE should be rated as follows.
In U.S.A. : 120V plus/minus 10%, 50/60Hz, 15A or higher
In Europe : 220-240V plus 6% or minus10%, 50/60Hz, 10A or higher
2. The equipment must be on an exclusive circuit
3. The outlet must be near the equipment and easily accessible.
I Norge: Kan kobles til IT strøm distribusjonssystemer.
1. Make sure to connect this equipment to a grounded outlet.
2. For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near
the equipment and shall be easily accessible.
The site temperature range = 10 to 32 degrees Centigrade, with the humidity between
15% to 85% RH. (NON CONDENSING)
Keep the printer away from water sources, boilers, humidifiers, refrigerators or kerosene
(oil) stove.
1. The installation site must not have open flames, dust or ammonia gases.
2. The equipment must not be exposed to the air vents from air conditioners.
It may affect the image quality.
3. The equipment should not be exposed to the direct sunlight.
Please draw curtains to block any sunlight.
When you open the Movable Unit, do not expose the Photoconductive Drum
to strong (intense) light as this will damage the Drum.
Ozone will be generated while this equipment is use, although the quantity generated
is within safe levels. (see certifications)
Ventilate the room, if required.
Keep ample room around the equipment to ensure comfortable operation.
(Refer to the following figure.)
The equipment must be leveled and the floor strength must be ample to sustain the
weight of the equipment.
(Rear)
30cm/12” or larger
(w/o option)
KIP 7170
L*
(Front)
80cm/32” or larger
90cm/35.4” or larger
for Paper Tray (option)
.
R*
* L + R = 35cm/14” or larger
(R must be larger than L)
(L = 5cm/2” or larger
recommended)
Chapter 1 Before Use 1-2
1. 2 Originals Prohibited from Duplication
It is not necessarily allowed to copy every kind of original.
You may be punished by the law if only you possess the copy of some kind of original.
We recommend you to consider enough before you copy such original.
[Originals prohibited from copying by the law]
1. It is not allowed to copy Currency (Bill, Money, Bank Note, etc.), Government issued
Negotiable Instruments (National Bonds, Security, Local Debt Bonds, etc.).
2. It is not allowed to copy Foreign Currency or Foreign Negotiable Instruments.
3. It is not allowed to copy unused postal stamps or government postcards without permission
to make replica from Government.
4. It is not allowed to copy Government issued revenue stamps, certificate stamps which are
prescribed by Liquor Tax Act or the Commodity Tax Act.
[Special items to be cared]
1. It is warned by the government to copy private issued securities (stock certificate, draft,
check, goods ticket, etc.), commutation ticket or book of tickets, excluding that some specific
company copies such originals as many as it requires for its own business.
2. We recommend you not to copy freely such originals as government issued passport, public
or private issued licenses, automobile inspection certification, IDs and tickets like pass or
meal.
Reference Law Prohibited items to copy
Regulations to control fake currency and
Bond.
Control Law against Forged & faked
Foreign Currency, Bill, Bank Note and Bond
Forged postal stamps control law Unused postal stamps or government postcards
Forged revenue stamps control law Government issued revenue stamps, and
Currency similarity securities Control Law Private issued securities (stock, draft, check,
[Originals protected by the copyright]
It is prohibited to copy such originals as book, music, paintings, printed copy, maps, drawings,
movie and pictures which are protected by the copyright, except for personnel or family use or
similar purpose.
Currency (Bill, Money, Bank Note, etc.),
Government issued Negotiable Instruments
(National Bonds, Security, Local Debt Bonds,
etc.)
Foreign Currency or Foreign Negotiable
Instruments
certificate stamps prescribed by Liquor Tax Act
or Commodity Tax Act
goods ticket, etc.), commutation or book tickets
Chapter 1 Before Use 1-3
1. 3 Features
(1) KIP 7170 is a single footprint Multi-Function Printer which can copy, scan and print.
Advanced drivers and comprehensive print utilities make the KIP 7170 an advanced, easy to
use system. (some functions may be optional)
(2) KIP HDP technology generates no waste toner.
(3) The KIP HDP Plus imaging system produces high definition lines, distinctive greyscale and
consistent blacks.
(4) The maximum paper width is 36” (914mm) wide, and the minimum is 11” (279mm). The
maximum paper length is 6m (with 36” paper) or, and the minimum is 8.5” (210mm).
(5) Up to 600dpi print resolutions with an enhanced scanning system produces the highest quality
images controlled by an advanced KIP Image Process System.
(6) Easy access to USB port allows users to provide efficient productivity by using “File to Print” /
“Scan to USB” (option).
(7) 2-way print delivery (front, up to 50 sheets of plain paper / rear) suits the preference of the
user’s print handling. (rear stacking requires a stacking device, option)
(8) Various media source; roll media feeding (2 rolls), cut sheet manual feeding, Paper Tray
multiple cut sheet feeder (option)
(9) Contactless IC card reader for more efficient accounting management (option)
(10) KIP 7170 adopts 12.1 inch screen for the UI, wider than 8.5 for our old products.
The capacitive multi-touch screen offers smooth, various and intuitive user operation that a
pressure sensing device lacks.
Chapter 1 Before Use 1-4
1. 4 Specifications
1. 4. 1 General
Subject Specification
Model KIP 7170
Configuration Console
Power consumption
(Maximum)
Power consumption
(Low power mode)
Acoustic noise Idling Max. 50db
Ozone Max. 0.05ppm (Measurement method under UL Standard)
Dimensions In case of attaching UI, Tray
Weight About 244kg (538lb)
Environmental condition
for usage
Interface Network Interface (10 BASE-T / 100 BASE-TX / 1000 BASE-T)
Rating Input Power In the US : 120V plus/minus 10%, 50/60Hz, 12A
NOTE
The above specifications are subject to change without notice.
1,440W (US model)
1,680W or less (EU / Asia model)
(scanner / controller included)
Conformity with International Energy Star Program
Printing Max. 57db
(impulse sound excluded) EN ISO 7779
1587mm (Width) x 704mm (Depth) x 1510mm (Height)
In case of excluding UI, Tray
1346mm (Width) x 704mm (Depth) x 1105mm (Height)
(Temperature)
10 to 32 degrees Centigrade / 50 to 89.6 F
(Humidity)
15 to 85% RH
USB2.0 (5VDC max)
In Europe : 220-240V plus 6% or minus 10%, 50/60Hz, 7A
Chapter 1 Before Use 1-5
1. 4. 2 Printer part
Subject Specification
Printing method LED Array Electro photography
Photoreceptor Organic Photoconductive Drum
Print speed 80mm per second
(Inch) 3.4ppm/E 5.8ppm/D Landscape
(Metric) 3.3ppm/A0 5.6ppm/A1 Landscape
Print head LED Array
Resolution of print head 600dpi x 2400dpi
Print width Maximum 914mm / 36”
Minimum or 297mm / 11” (roll media)
or 210mm / 8.5” (cut sheet)
Print length Maximum
(Standard) 6,000mm / 19.7ft for 36” / A0 wide
or “5 x Standard length” (plain paper / bond)
“2 x Standard length”
“1 x Standard length”
(Option) 64,000mm
Minimum 210mm / 8.5”
NOTE :
If the print is longer than the mentioned above, its image quality or the reliability of paper
feeding is not guaranteed.
Paper feeding method 2 Roll Decks
Manual Feeder (single cut sheet)
Paper tray (multiple cut sheet, option)
Print size
(from Paper Tray, option)
ISO (mm)
Width
Length
594 420 297 210
420 X X
297 X X
ANSI (inch)
Width
Length
24 22 18 17 12 11 9 8.5
18 X X
17 X X
12 X X
11 X X
Warm up time Shorter than 4 minutes 30 seconds
First print time 21 seconds (D Landscape, Front Stacking)
(At 23
(At 23
o
C, 60%RH, the rated voltage, and plain paper is used)
o
C, 60%RH, the rated voltage, and plain paper is used)
Fusing method Heat and Pressure Rollers
Development method Dry type non-magnetic mono-component toner
(tracing paper / vellum)
(film)
(plain paper / bond)
Chapter 1 Before Use 1-6
Subject Specification
Media (Recommended Media)
US model:
Bond 64g/m
Vellum US Vellum (XV-20)
Film 4MIL (PF-4DME)
EU / Asia model:
Plain Paper 64g/m
Tracing Paper Gateway Tracing Paper (73g/m
Film NSF4mil
Storage of consumables (Toner cartridge)
Store the cartridge within the temperature range from 0 to
35 degrees Centigrade and within the humidity range from 35
to 85% RH.
NOTE
The above specifications are subject to change without notice.
2
to 80g/m2, US Bond (PB-20)
2
to 80g/m2
2
)
Chapter 1 Before Use 1-7
1. 4. 3 Scanner part
Subject Specification
Scanning method Contact Image Sensor (CIS)
(5 pieces of A4 sized CIS)
Light source LED (R/G/B)
Scanning speed
(600 dpi, normal quality)
(max)
Setting of original Face up
Starting point of scan Center
Scan width Max: 914.4mm / 36”
Scan length Max: 6,000mm / 19.7ft (Including the margin area)
Optical resolution 600dpi
Digital resolution 200 / 300 / 400 / 600 dpi
Original transportation Sheet through type
Transportable original
thickness
Monochrome : 65mm/s
Grayscale : 65mm/s
Color : 22mm/s
NOTE : The actual speed may vary by the scan software.
Min : 210mm
Min : 210mm / 8.5” (Including the margin area)
NOTE :
If the print is longer than 6,000mm, its image quality or the reliability of paper feeding is not
guaranteed.
Max: 1.60mm
Min : 0.05mm
NOTE :
Suggest to change “It does not guarantee both scan/copy image quality and original feeding
reliability in case the original is non-standard size one of which thickness is 0.25mm or thicker.
NOTE
The above specifications are subject to change without notice.
Chapter 1 Before Use 1-8
1. 5 Appearance
1. 5. 1 Front view
No. Name Function
1 Main Switch You can turn on/off the KIP 7170.
2 Original Guides Feed the original under the Scanner Unit along the Original
3 User Interface This is a Touch Screen, and many kinds of user operation are
4 Scan Abort Button While scanning: emergency stop
5 Start Button Starts scanning if the controlling software requires user
6 Scanner Unit Read the original with this unit when you make scan or copy.
7 Toner Hatch
8 Engine Unit Open Lever Pull up these levers when you open the Engine Unit.
9 Bypass Feeder Feed a cut sheet paper from the Bypass Feeder.
10 Roll Deck Roll media can be loaded here.
11 Print Tray These trays catch ejected prints.
12 LED Indicator Indicates the status of Scanner Unit.
13 USB Port Your USB flash memory storage can be installed here.
14 Paper Tray (OPTION) Multiple cut sheets can be stored inside (up to 50)
2
7
8
9
10
14
(Original Table)
6
11
Guides.
available.
PLEASE DO NOT push the LCD area too strong.
At Standby position: eject
intervention.
Open the Toner Hatch when you replace the Toner Cartridge.
Also put the original here and then feed it into the Scanner Unit
when you make scan or copy.
green: Ready red: Error
green to-and-fro: Scanning red flashing:Scanner Unit Open, Jam
5VDC max.
12
11
4
5
3
13
2
1
8
Chapter 1 Before Use 1-9
1. 5. 2 Rear view
No. Name Function
1 Paper Exit Door Open the Paper Exit Door when you remove the paper
2 COM Port For an optional device
3 USB Port For an optional device
4 LAN Port Connect the LAN Cable to connect the KIP 7170 to the
5 Dehumidify Heater Switch
6 Breaker It is possible to shut off supplying the AC power.
7 Inlet Socket Connect the Power Cord here.
2
3
4
5
6
7
(DEHUMIDIFY KIT is an
optional part.)
misfed inside the Fuser Unit.
(D-Sub Connector 9 pins: 12VDC max.)
Service Use. 5VDC max.
network. (Do not connect a telephone line)
Turn on the Dehumidify Heater with this switch when you
would like to dry the paper in the humid season.
1
Chapter 1 Before Use 1-10
1. 6 Specifications for Scan Original
A scan original must satisfy the following specifications.
Thickness 0.05mm to 1.60mm
Width 210mm to 914.4mm
Length 210mm to 6,000mm
NOTE :
1. Suggest to change “It does not guarantee both scan/copy image quality and original feeding reliability in case the original is nonstandard size one of which thickness is 0.25mm or thicker.
2. Image quality for an original over 6,000mm in length is not guaranteed.
1. 6. 1 Original Standards
(1) The width of original must range from 8.5” to 36” (210mm to 914.4mm).
(2) The length of original must range 8.5” (210mm) to 6,000mm
(3) The thickness of original must range from 0.05mm to 0.25mm.
(4) The shape of original must be square, and it must be standard sized.
(5) The type of original must belong to any of the followings.
Plain paper
Coated paper (High or middle class plain paper is coated with the paint.)
Tracing paper
Pansy Trace Paper (Both sides of the film is sandwiched between Tracing paper.)
Film
Newspaper
Cardboard paper
1. 6. 2 Special Documents
The following kinds of originals are “special”. It is possible to scan them, but the image quality
and feed reliability are not guaranteed.
(1) The type of original is acceptable, but the thickness and type may not be:
Booklets
Original with a Hanger
Cut and Pasted originals
(2) These original may not damage the scanner, but these types are NOT recommended:
following ones.
Cloth
Aluminium Kent Paper
Chapter 1 Before Use 1-11
1. 6. 3 “Do Not Scan” Originals
It is impossible to use the following types of originals because they are likely to damage the
scanner.
Do not scan the following kinds of original, because you may damage the original or scanner itself!
Sticked with paste
Paste
Torn
Folded (Leading edge)
So much curled
(Diameter is smaller than
80mm.)
Chapter 1 Before Use 1-12
Not square
Wet image
Made of metal or fabric
Wet
Metal Fabric
Rough surface
(Carbon paper for example)
Clipped or stapled
Rough surface
Clipped Stapled
Chapter 1 Before Use 1-13
The following kinds of originals can be read with using a carrier sheet.
However, the image quality and feed reliability are not guaranteed.
Patched
Punched
Chapter 1 Before Use 1-14
1. 7 Specifications for the Printing Media
1. 7. 1 Papers not available to use
Do not use the following kinds of printing paper. Doing so may damage the print engine.
Excessively curled
(a diameter of 50 mm or
less)
Folded
Creased
Torn
Punched
Chapter 1 Before Use 1-15
Pre-printed
Extremely slippery
Extremely sticky
Extremely thin and soft
OHP Film
CAUTION
Do not use the paper with staple, or do not use such conductive paper as aluminium foil and
carbon paper.
The above may result in a danger of fire
NOTE
(1) Print image may become light if printed on a rough surface of the paper.
(2) Print image may become defective if the print paper has an excess curl.
(3) It will become a cause for paper mis-feed, defective print image or paper creasing if you
use a paper that does not satisfy the specification.
(4) Do not use a paper of which surface is very special, such as thermal paper, art paper,
aluminium foil, carbon paper and conductive paper.
(5) Do not use papers with unpacked (exposed in high / low temperature & humidity) in a
long period. Such papers may result in mis-feed, defective image or paper creasing.
(6) Tracing paper exposed to air over a long period tends to cause a defective printing.
Removing one round on the surface of the tracing roll paper from the beginning is
recommended.
Refer to [2.3 Replacing Roll Media].
1. 7. 2 Keeping the paper in the custody
Keep the paper in the custody taking care of the following matters.
1. Do not expose the paper to the direct sunlight.
2. Keep the paper away from high humidity. (It must be less than 70%)
3. Put the paper on a flat place
4. If you will keep the paper in the custody, which you have already unpacked, put it into the
polyethylene bag to avoid the humidity.
Chapter 1 Before Use 1-16