Kino Flo Celeb 400Q DMX LED User Manual

Operation Manual

®

Celeb 400Q DMX LED

Part No. 3100077 Rev A 03-11-2014

Celeb 400Q DMX LED Fixtures

CEL-400Q-120U

Celeb 400Q DMX Yoke Mount, Univ 120U

CEL-400Q-230U

Celeb 400Q DMX Yoke Mount, Univ 230U

CEL-400QP-120U

Celeb 400Q DMX Pole-Op, Univ 120U

CEL-400QP-230U

Celeb 400Q DMX Pole-Op, Univ 230U

Included w/ all Celeb 400Q Models

LVR-CE490-Q

Celeb 400Q Louver-Honeycomb, 90° (Included)

GFR-CE4-Q

Celeb 400Q Gel Frame (Included)

KIT-C4Q-120U

Celeb 400Q DMX Yoke Mount Kit,
Univ 120U

KIT-C4Q-230U

Celeb 400Q DMX Yoke Mount Kit,
Univ 230U

Kit Contents: Dimensions:

1 Celeb 400Q DMX Yoke Mount 34.5 x 33 x 8”
1 Jr. Pin (88 x 84 x 22cm)
1 Ship Case

Weight:
52 lb

(24kg)

2

Celeb 400Q DMX Control Panel

A GB C D E F

A) Kelvin Preset Buttons: Kelvin buttons come preset at the factory.
Factory defaults left to right are: 2700K, 3200K, 4000K, 5000K, 5500K.
User can also use these preset buttons to store custom Kelvin settings.

B) DMX ADDRESS – Use to set DMX address. The Celeb 400Q
automatically assigns 2 channels. First Channel controls Dimming;
Second Channel controls Kelvin.

C) KELVIN / DIM: In KELVIN mode, an amber light appears to the left of
the button and Kelvin is displayed. Press the button again to change to
DIM mode. In DIM mode, a green light will appear to the left of the button
and Dim level is displayed.

D) Display: Provides Kelvin, Dim level and software revision data.

E) LOCK / RESET: In LOCK mode, an amber light is displayed to the left

of the button. In RESET mode, the indicator light is green. To reset to
factory presets, hold the LOCK / RESET button for 5 seconds.

F) On / Off: On = Green light displayed. Off = Amber light displayed.

G) Kelvin / Dimmer Knob: Manually adjusts Kelvin or Dim levels.

Press the knob to toggle between ne and coarse adjustments.

Note: Each Celeb 400Q DMX xture has an “AUTO TERMINATE” feature.
The last xture that does not have an XLR cable attached to the
DMX “Out” port will automatically terminate.

IMPORTANT!

The dimmer board/light console should have its channel set to LINEAR light output
response. (LINEAR response is the default setting on most dimmer boards.)

3

Fixture Power

AC Input

The Celeb is powered AC and includes an IEC connection. A locking

power cord is included with the xture. To remove the plug, move the red tab

to release. The ballast has a built-in power supply with universal input from
100-240VAC.

DC Input

The Celeb can also be operated on 24VDC (input range 18-28VDC) through
a 3-Pin XLR. A low voltage warning will display “LPWR” when the battery is
running low.

The pin polarity is:

Pin #1 – Ground
Pin #2 + 18-28VDC
Pin #3 not used

Ambient Operating Temperature

The Celeb is designed to operate at temperatures from 14°F to 104°F
(-10°C to 40°C).

4

Start Up

When power is rst applied to
the xture, the alphanumeric

display shows the current
software version.

Press the On/Off button
to turn on the xture.
The display will default to a
Kelvin setting of 5000.

Kelvin Selection

There are 5 Kelvin factory
preset buttons. Left to right
they display 2700K, 3200K,
4000K, 5000K and 5500K.

A green indicator will light to
the left of the active button.

Rotating the adjustment knob
will change the Kelvin.

Press the rotating knob once
to shift the Kelvin prole from
Coarse to Fine increments.

In the Coarse mode,
the xture can be adjusted in
one rotation of the knob.
In Fine mode, it will require
8 rotations for full range of
adjustment.

5