Kino Flo Celeb 200 DMX LED User Manual

Operation Manual

®

Celeb 200 DMX LED

Part No. 3100065 Rev B 08-28-2014

Celeb 200 DMX LED System

Celeb 200 Center Mount

Celeb 200 Yoke Mount

Celeb 200 Pole-Op

CEL-200C-120U

Celeb 200 DMX Center Mount, Univ 120U

CEL-200C-230U

Celeb 200 DMX Center Mount, Univ 230U

CEL-200Y-120U

Celeb 200 DMX Yoke Mount, Univ 120U

CEL-200Y-230U

Celeb 200 DMX Yoke Mount, Univ 230U

CEL-200P-120U

Celeb 200 DMX Pole-Op, Univ 120U

CEL-200P-230U

Celeb 200 DMX Pole-Op, Univ 230U

Included w/ all Celeb 200 Models

LVR-CE290-P

Celeb 200 Louver/HP 90° (Included)

GFR-CE2

Celeb 200 Gel Frame (Included)

2

Celeb 200 DMX LED Kit

KIT-C2-120U

Celeb 200 DMX Center Mount Kit,
Univ 120U

KIT-C2-230U

Celeb 200 DMX Center Mount Kit,
Univ 230U

Kit Contents:

1 Celeb 200 DMX Center Mount
1 Flight Case

Weight: 31 lb (14kg)

Dimensions: 29 x 10.5 x 17”

(74 x 27 x 43cm)

3

Celeb 200 DMX Control Panel

A GB C D E F H

A) Kelvin Preset Buttons: Kelvin buttons come preset at the factory.
Factory defaults left to right are: 2700K, 3200K, 4000K, 5000K, 5500K.
User can also use these preset buttons to store custom Kelvin settings.

B) DMX ADDRESS – Use to set DMX address. The Celeb 200 automatically
assigns 2 channels. First Channel controls Dimming; Second Channel
controls Kelvin.

C) KELVIN / DIM: In KELVIN mode, an amber light appears to the left of
the button and Kelvin is displayed. Press the button again to change to
DIM mode. In DIM mode, a green light will appear to the left of the button
and Dim level is displayed.

D) Display: Provides Kelvin, Dim level and software revision data.

E) LOCK / RESET: In LOCK mode, an amber light is displayed to the left

of the button. In RESET mode, the indicator light is green. To reset to
factory presets, hold the LOCK / RESET button for 5 seconds.

F) On / Off: On = Green light displayed. Off = Amber light displayed.

G) Data: To update Software Revisions.

H) Kelvin / Dimmer Knob: Manually adjusts Kelvin or Dim levels.

Press the knob to toggle between ne and coarse adjustments.

Note: Each Celeb 200 DMX xture has an “AUTO TERMINATE” feature.
The last xture that does not have an XLR cable attached to the
DMX “Out” port will automatically terminate.

4

Ballast Power

AC Input

The Celeb is powered AC and includes an IEC connection. A locking power cord is

included with the xture. To remove the plug, move the red tab to release. The xture

has a built-in power supply with universal input from 100-240VAC.

Note: When operating AC, attach the Velcro strap around the baby receiver lollipop as

a strain relief. The handles also provide an attachment point for a safety chain if xture

is hung from a grid.

DC Input

The Celeb can also be operated on 24VDC (input range 18-28VDC) through a 3-Pin
XLR. The Celeb will run approximately 2 hours on a 320W/24V/13A battery belt. A low
voltage warning will display “LPWR” when the battery is running low.

The pin polarity is:

Pin #1 – Ground
Pin #2 + 18-28VDC

Pin #3 not used

Ambient Operating Temperature

The Celeb is designed to operate at temperatures from 14°F to 104°F
(-10°C to 40°C).

5

Start Up

When power is rst applied to
the xture, the alphanumeric

display shows the current
software version.

Press the On/Off button
to turn on the xture.
The display will default to a
Kelvin setting of 5000.

Kelvin Selection

There are 5 Kelvin factory
preset buttons. Left to right
they display 2700K, 3200K,
4000K, 5000K and 5500K.

A green indicator will light to
the left of the active button.

Rotating the adjustment knob
will change the Kelvin.

Press the rotating knob once
to shift the Kelvin prole from
Coarse to Fine increments.

In the Coarse mode,
the xture can be adjusted in
one rotation of the knob.
In Fine mode, it will require
8 rotations for full range of
adjustment.

6