Kino Flo 4Bank DMX Operation Manual
Operation Manual
Part No. 3100070 Rev B 02-10-2016
4Bank DMX
2
Systems
CFX-484 4ft 4Bank Fixture w/ Louver/HP, 90°
CFX-244 2ft 4Bank Fixture w/ Louver/HP, 90°
MTP-KF41 Kino 41K Mount w/ 3/8” Pin (10mm)
X16-25 4Bank Extension, 25ft
BAL-457-120U 4Bank DMX Ballast, Univ 120U
BAL-457-230U 4Bank DMX Ballast, Univ 230U
Each 4Bank DMX System consists of:
1 Fixture
1 Mounting Plate
1 Extension Cable
1 4Bank DMX Ballast
True Match Lamps
488-K32-S/6P 4ft Kino KF32 (1 x 6pk)
488-K55-S/6P 4ft Kino KF55 (1 x 6pk)
242-K32-S/6P 2ft Kino KF32 (1 x 6pk)
242-K55-S/6P 2ft Kino KF55 (1 x 6pk)
®
3
Lighting Kits
KIT-2GF-X120U
Gaffer DMX Kit, Univ 120U
KIT-2GF-X230U
Gaffer DMX Kit, Univ 230U
Kit Contents:
2 4ft 4Bank Fixture
2 4Bank DMX Ballast
2 MTP-BC41 Mount
w/ Baby Receiver (16mm)
2 Extension, 25ft
2 Lamp Case
1 Gaffer Ship Case
Dimensions: Weight:
56.5 x 13 x 21.5” 73.5 lb
(143.5 x 33 x 55cm) (33.5kg)
KIT-2NT-X120U
Interview DMX Kit, Univ 120U
KIT-2NT-X230U
Interview DMX Kit, Univ 230U
Kit Contents:
2 2ft 4Bank Fixture
2 4Bank DMX Ballast
2 MTP-BC41 Mount
w/ Baby Receiver (16mm)
2 Extension, 25ft
2 Lamp Case
1 Interview Ship Case
Dimensions: Weight:
35.5 x 13 x 22” 57.5 lb
(90 x 33 x 56cm) (26kg)
Gaffer DMX Kit
Interview DMX Kit
Fixture Assembly
The 4Bank xture is comprised
of a removable Louver, Reector
and Lamp Harness. The Louver
and Reector are held in place
with Velcro fasteners. The Lamp
Harness is secured by means of
a ¼ turn fastener and two clips.
The Harness wiring is color-coded. The same color-code must match at each end of
the lamp for proper operation.
To Release the Lamp Harness
Remove the harness from 2 clips located under the reector. Rotate the ¼ turn
fastener clockwise to release harness.
The lamps can operate independent of the xture
allowing them to be built into sets or custom soft boxes
or hand-held as a single tube for an eye-light.
WARNING: Always use safety-coated lamps to avoid
injury if lamp breaks.
4Bank Harness
Lamp Harness Color Codes
White
Black
White
Black
4
5
Inserting Lamps
Gelling the Fixture
Locking Lamp Connector:
Depress both tabs on lamp connector and apply to lamp pins.
Match the Harness color-codes at each end of the lamp.
Push lamps into the xture’s Lamp Holder Clips.
Restricting the airow around the lamps can cause the lamp to
operate hotter. This increased heat will raise the lamp’s color
temperature and green spike. Therefore, it is recommended to
clip gels to the doors of the xture.
Remove Louver. Do Not clip gels to louver.
Do Not block the xture ends in a manner that restricts airow.
Loading...