Kino Flo 115, 105 User Manual
Operation Manual
4Bank, Double & Single
Select
Part No. 3100052 Rev A 9-12-2013
Systems
4Bank
Double Single
Each System consists of:
1 Fixture
1 Mounting Plate
1 Extension Cable
1 Select Ballast
2
True Match Lamps
488-K29-S 4ft Kino KF29
488-K32-S 4ft Kino KF32
488-K55-S 4ft Kino KF55
242-K29-S 2ft Kino KF29
242-K32-S 2ft Kino KF32
242-K55-S 2ft Kino KF55
®
Lighting Kits
KIT-2GF-120
Gaffer Kit, 120VAC (2-Unit)
KIT-2GF-230
Gaffer Kit, 230VAC (2-Unit)
Gaffer Kit
4ft 4Bank Kit
Kit Contents:
2 4ft 4Bank System
w/ MTP-BL41 Mount
2 Lamp Case
1 Gaffer Ship Case
Dimensions: Weight:
56.5 x 13 x 21.5” 73.5 lb
(143.5 x 33 x 55cm) (33.5kg)
KIT-4804B-120
4ft 4Bank Kit, 120VAC (1-Unit) w/ Soft Case
KIT-4804B-230
4ft 4Bank Kit, 230VAC (1-Unit) w/ Soft Case
Kit Contents:
1 4ft 4Bank System
w/ MTP-BL41 Mount
1 Lamp Case
1 Soft Case
Dimensions: Weight:
55 x 8 x 19.5” 26 lb
(140 x 20.5 x 49.5cm) (12kg)
3
Lighting Kits
KIT-2NT-120
Interview Kit, 120VAC (2-Unit)
KIT-2NT-230
Interview Kit, 230VAC (2-Unit)
Interview Kit
(2-Unit)
2ft 4Bank Kit
Kit Contents:
2 2ft 4Bank System
w/ MTP-BL41 Mount
2 Lamp Case
1 Interview Ship Case
Dimensions: Weight:
35.5 x 13 x 22” 57.5 lb
(90 x 33 x 56cm) (26kg)
KIT-2804B-120
2ft 4Bank Kit, 120VAC (1-Unit) w/ Soft Case
KIT-2804B-230
2ft 4Bank Kit, 230VAC (1-Unit) w/ Soft Case
Kit Contents:
1 2ft 4Bank System
w/ MTP-BL41 Mount
1 Lamp Case
1 Soft Case
Dimensions: Weight:
28.5 x 7.5 x 20” 20.5 lb
(72.5 x 19 x 51cm) (9.5kg)
KIT-3NT-120
Interview Kit, 120VAC (3-Unit)
Interview Kit
4
(3-Unit)
KIT-3NT-230
Interview Kit, 230VAC (3-Unit)
Kit Contents:
1 2ft 4Bank System
w/ MTP-BL41 Mount
2 2ft Double System
w/ MTP-BL41 Mount
2 Lamp Case
1 Interview Ship Case
Dimensions: Weight:
35.5 x 13 x 23” 64 lb
(90 x 33 x 58.5cm) (29.4kg)
Fixture Assembly
The 4Bank, Double and Single xtures are comprised of a removable Louver, Reector
and Lamp Harness. The Louver and Reector are held in place with Velcro fasteners.
The Lamp Harness is secured by means of a ¼ turn fastener and two clips.
To Release the Lamp Harness
Remove the harness from 2 clips located under the reector. Rotate the ¼ turn
fastener clockwise to release harness.
The lamps can operate independent of the xture
allowing them to be built into sets or custom soft boxes
or hand-held as a single tube for an eye-light.
WARNING: Always use safety-coated lamps to avoid
injury if lamp breaks.
Lamp Harness Color Codes
Red
Yellow
Black
Blue
4Bank Harness
The Harness wiring is color-coded. The same color-code must match at each end of
the lamp for proper operation.
Double Harness
Red
Yellow
5
Inserting Lamps
Locking Lamp Connector:
Depress both tabs on lamp connector and apply to lamp pins.
Match the Harness color-codes at each end of the lamp.
Push lamps into the xture’s Lamp Holder Clips.
Gelling the Fixture
Restricting the airow around the lamps can cause the lamps to
operate hotter. This increased heat will raise the lamp’s color
temperature and green spike. Therefore, it is recommended to
clip gels to the doors of the xture.
Do Not clip gels to louver.
Do Not block the xture ends in a manner that restricts airow.
6
Loading...