Kingtronics Co KL1050C User Manual

Find more online at www.codelockssupport.com

Page 2

1.

2.

3.

4.

1.

2.

3.

4.

1.

2.

3.

4.

1.

2.

3.

4.

a.

5.

6.

1.

1.

2.

3.

4.

5.

6.

1.

2.

3.

4.

1.

2.

3.

4.

First Use (Initialisation)

When you first put batteries into the lock,
both Red and Blue LEDs will flash
continuously and the lock will be unlocked.

For Private Use:

Open the handle to expose the #
button.
Press and hold the # button until
the Red LED is on continuously.
Touch a compatible card to
the front of the lock - the Blue LED
will flash to confirm card
acceptance. This card is now your
Master User Card.
Press the # button to finish.

For Public Use:

Open the handle to expose the #
button.
Press and hold the # button until
the Red LED is on continuously.
Touch a compatible card to the
front of the lock - the Blue LED will
flash to confirm card acceptance.
This card is now your Master User
Card.
Within 10 seconds of registering
the Master User Card, touch a
second compatible. card to the
front of the lock. The Blue LED will
flash to confirm card acceptance.
This card is now your first
Technician Card and the lock will
go into Public Function.

Change the Mode

To change between Public and Private
Functions:

Touch the Master User Card to the
front of the lock.
Open the handle to expose the #
button.
Press the # button 3 times in quick
succession.
The Blue LED will flash 3 times to
indicate private function. The Red
LED will flash 3 times to indicate
public function.

The motor will enable - this is expected
behaviour.

Using the Lock - Public

Use

The lock will remain open until the next user
touches a compatible card to the front of the
lock. Once locked, the lock will only be able
to be opened by the same card that was
used to lock the lock, the Master User Card
or the Technician Card.

When locked, the Red LED will flash every
5 seconds to indicate that the lock is locked.

If the Master User Card is used to open the
lock, the existing User Card will be deleted.

If the Technician Card is used to open the
lock, the existing User Card will be retained
and after 4 seconds, the lock will re-lock.

Add/Remove a Technician
Card

If the lock was previously in Private
Function, a Technician Card can now be
added. Note that adding a Technician Card
will place the lock into Public function. up to
10 Technician Cards can be added:

Touch the Master User Card to the
front of the lock.
Open the handle to expose the b#
utton.
Press and hold the button until#
the Red LED is lit. Release as soon
as the Red LED is lit.
Touch an unregistered compatible
card to the front of the lock. Both
LED's will flash and the motor will
run to confirm acceptance.

For removing a registered
Technician Card the Red
LED will flash twice and

the card removed.
To register additional Technician
Cards, repeat step 4 within 10
seconds.
To end the sequence press and
release the # button or wait 10
seconds and the programme will
end itself.

Note: If the card is already registered,
the Red LED will flash and the card will be
removed from the lock.

Enable Public Pairing

Public pairing prevents a User Card that has
been used to lock one lock from being able
to be used to lock additional locks whilst it is
paired with the original lock.

Touch the Master User Card to the
front of the lock.

Using the Lock - Private

Use

Open the lock by touching the Master User
Card or a User Card to the front of the lock.
The lock will remain open for 4 seconds
before re-locking.

Add/Remove a User Card

Touch the Master User Card to the
front of the lock.
Open the handle to expose the b#
utton.
Press and release the button, the#
Blue LED will turn on after 2
seconds.
Touch an unregistered User Card
to the front of the lock. The Blue
LED will flash and the motor will run
to confirm acceptance.
To register additional User
Cards, repeat step 4 within 10
seconds.
To end the sequence press and
release the # button, or do not
touch the lock for 10 seconds and
the programme will end itself.

Note: If the card is already registered,
the Red LED will flash and the card will be
removed from the lock.

Removing all User Cards

Touch the Master User Card to the
front of the lock.
Open the handle to expose the #
button.
Press and release the button.#
The Blue LED will turn on after 2
seconds.
Press and hold the button for 5#
seconds. All User Cards will be
removed.

Removing all Technician
Cards

Touch the Master User Card to the
front of the lock.
Open the handle to expose the b#
utton.
Press and hold the button until#
the Red LED is lit. Release as soon
as the Red LED is lit.
Press and hold the # button until
you see both the Blue and Red
LED lights at the same time. All
Technician Cards will be removed.

Find more online at www.codelockssupport.com

Page 3

2.

3.

1.

2.

3.

Open the handle to expose the b#
utton.
Press and hold the button for 10#
seconds. Both LED's will illuminate
to indication successful change,
followed by the Blue LED for Public
Pairing enabled or the Red LED for
Public Pairing disabled.

Low Battery

When the battery power is low the Red LED will flash three times
before the Blue LED flashes to signal acceptance of the smart card.
Batteries should be changed as soon as this happens.

The lock will operate for approximately 100 times with low battery.

Battery failure override

The Cabinet Lock has been designed so an external PP3 battery can
be placed against the contact points surrounding the Blue and Red
LED’s so the lock can be opened to replace the batteries should they
fail.

The procedure is as follows:

Place the contact points of the PP3 battery against the
contact points surrounding the Blue and Red LED’s.
The positive + PP3 terminal against the RED LED contact
point and the negative – PP3 terminal against the Blue LED.
Touch the Master Smart Card.
The motor will withdraw the locking pin allowing the lock to
be opened.
Fit new batteries by removing the upper fixing bolt and
swinging the lock down over the edge of the door. Refit the
lock.

Factory Reset

The factory reset procedure requires the door to be open and the lock
to be in an unlocked state.

Reset the Lock

Remove the rear-fixing bolt and swing the lock over the edge
of the door to reveal the battery compartment.
Remove one battery.
Press and hold the # button, replace the battery, the blue
LED will flash twice, release the # button. Within three
seconds press the # button three times. The blue LED will
flash twice and the lock will have reverted to the factory
default. All the registered smart card are removed.

CODELOCKS HEADQUARTERS
Tel: [phone]
Fax: [phone]

[e-mail]
www.codelocks.com

Helpline, service & spares Freephone: 0800
393 405

POI-KL1050-v1:1216

CODELOCKS INC US
Tel: [phone]
Fax: [phone]

[e-mail]
www.codelocks.us

Helpline, service & spares Toll free:

1.877.codelock

CODELOCKS (Australia) PTY LTD
Tel: [phone]
Fax: [phone]

[e-mail]
www.codelocks.com.au

Helpline, service & spares Toll free: 1800
052 131