King Technology POOL FROG ABOVE GROUND MINERAL SYSTEM User Manual

Download

Page 1

Pool FROG

ABOVE GROUND

MINERAL SYSTEM FOR POOLS

Patented Mineral Pool Sanitizer

THE POOL FROG

MINERAL RESERVOIR

MUST BE REPLACED

EVERY SIX MONTHS OR

AFTER ONE POOL

SEASON WHICHEVER

IS SHORTER.

Instruction Manual

Customer Service 800-222-0169

Page 2

TABLE OF CONTENTS

POOL FROG® Introduction 3

Swimming Pool Tips 4

Start-up and Operation 5-6

Replacing POOL FROG® Mineral Reservoir 7

Replacing FROG BAM

Replacing POOL FROG

Bac Pac 9

Troubleshooting 10

Parts List 11

Replacing Control Dial O-Rings 12

Replacing Cap O-Ring and Knob 12

Winterizing 13

Above Ground Filter Installation 14

Above Ground Base Installation 15

Warranty 16

Page 3

POOL FROG

Welcome to easier pool care courtesy of POOL FROG®. With POOL FROG pool water will look and feel better without a lot of work or a lot of chlorine. system controls bacteria using a combination of minerals and reduced chlorine

levels–up to 50%* less. There are 4 parts to the POOL FROG® System: The Above

Ground POOL FROG

Cycler, the POOL FROG® Mineral Reservoir, FROG BAM

90-day Algae Preventative and the POOL FROG® Bac Pac.

This

your

Part 1

POOL FROG

The water treatment center that controls the flow of water to each part of the POOL FROG® System.

Cycler

For Above Ground Pools up to 25,000 gallons.

Part 2

POOL FROG

Mineral Reservoir

Holds the minerals and fits inside the POOL FROG® Cycler.

ineral

L FRO

ith the

e used w

est results, the PO

uld

For b Reservoir sho

chlorine Bac Pac.

ove the

ly rem

Sim

s on the Bac

colored tab

ir.

insert into the

Pac and

f the Reservo

r o

cente

ur size

r yo

ial fo

and

Set the d

er d

l, size p

e p

-run tim

aintain a

rine

just to

chlo

and

.5 to 1 p

anual).

low

level (see m

from

or eq

o not put anything else into the center

ineral Reservo

e M

gy or d

of th

result.

uld

King Technolo

ent co

uip

r, floater or

l has an alternate so

If the p

(a chlorinato

rine

f chlo

feeding), a Flow

hand

laced in the center o

e p

ir to ensure go

ust b

ugh the m

ineral Reservo

thro

ater flo

a Flow

u need

If yo

lease call 1-800-222-0169

re you use the p

befo

BAM copy to come

ut a Bac Pac

ir b

age to the

urce

l Pac

ontro

f the od

inerals.

l Pac,

ontro

uct.

rod

THE POOL FROG¤ MINERAL RESERVOIR

MUST BE REPLACED

EVERY SIX MONTHS OR AFTER ONE

Part 3 FROG BAM

Use with the POOL

FROG Algae Protection Guarantee.

System for an

(

POOL FROG

POOL SEASON WHICHEVER IS SHORTER.

Part 4

POOL FROG

Pre-filled with chlorine tablets and fits inside the POOL FROG Mineral Reservoir.

Mineral Reservoir sold inside

POOL FROG

Bac Pac and FROG BAM® sold separately.)

POOL FROG

*Compared to the minimum EPA recommended chlorine level of 1.0 ppm for a stablized swimming pool.

Cycler and separately for replacements.

Bac Pac

Page 4

Swimming Pool Tips

Start-up and Yearly Maintenance

• Make sure the pool has adequate circulation. The pool

water must completely circulate through the pump and filter at least 1 to 2 times per day. This usually requires 8 to 12 hours. Check with your dealer for the proper circulation time for your pool.

• If your fill water is high in metals, use a sequestering agent

or metal out product at start-up only before using the POOL FROG® Mineral Reservoir. See your local dealer for details on using these products and always follow manufacturers directions carefully.

•After your pool is up and running

smoothly, continue to test your

water for pH, total alkalinity and chlorine and maintain its balance by adding any necessary adjustment products (see your dealer for details).

• Before beginning with any pool care program, you must

first balance your pool water. Take a water sample to your local pool professional or use a complete test kit that will test for the following important elements.

Water Balance Guidelines

pH: 7.2 — 7.8 Total Alkalinity: 60 — 120 ppm Calcium Hardness: 150 — 400 Total Dissolved Solids: <1500 Stabilizer: 20 — 80 ppm Free Chlorine: 0.5 — 1.0 ppm

• Check the pool's filter gauge often and periodically clean

filter per the manufacturer's directions. A dirty filter will slow the flow of water which could hamper proper circulation.

Page 5

Start-up and Operation

• Add a stabilizer or conditioner to

the pool at the beginning of the season if the stabilizer level is below 20 ppm. This will prevent chlorine burn off. Follow manufacturer’s directions carefully.

• Shock the pool with chlorine to rid

the water of all contaminants before beginning with POOL FROG manufacturer's directions carefully.

• THIS STEP IS VERY IMPORTANT

TO START-UP. USE CHLORINE SHOCK ONLY.

. Follow

• Replace cap and run POOL

FROG® Cycler, with POOL FROG

Mineral Reservoir inserted, for 10

minutes on Setting 10.

• For an Algae Protection

Guarantee insert FROG BAM into POOL FROG® Mineral

Reservoir in POOL FROG

(Follow directions on page 8.)

Cycler.

• Do not add shock in or near the skimmer or into the

POOL FROG® Cycler as it could damage equipment, risk potential explosion or discolor your pool surface.

• Install a POOL FROG

Reservoir into the POOL FROG Cycler. (Follow directions on page 7.)

REPLACE THE POOL FROG MINERAL RESERVOIR EVERY 6 MONTHS OR AFTER ONE POOL SEASON WHICHEVER IS SHORTER.

Mineral

• When chlorine reading is down

to 1.0 ppm, which may take a few days, insert POOL FROG Pac. (

Follow directions on page

9.)

Bac

Page 6

Start-up and Operation

• Set control dial by matching up the parameters of your pool on the chart below. THIS IS A

STARTING POINT ONLY and may need to be adjusted to fit your individual pool needs. See #8 for directions. IMPORTANT: Pump run times less than 8 hours could result in under chlorination due to inadequate flow through the System.

Above Grd.

POOL SIZE

llo

7,000 (18')

9,000 (21')

12,000 (24')

15,000

20,000

1/2 hp 3/4 hp 1 hp 1 1/2 hp

8 Hour Pump Run Time

PUMP SIZE

5 4.5 4 3.5

5.5 5 4.5 4 6 5.5 5 4.5

NR 6 5.5 5

NR NR 6 5.5

* – Bypass installation recommended. NR – This pump size is not recommended for this size pool.

Find your starting dial setting by matching up the parameters of your pool on the above chart. An above ground pool with approximately 12,000 gallons with a 1 horse pump running 12 hours a day would require a

starting setting of 4.5. See example at right.

• For the first week test the

pool water daily for free chlorine ensure correct dial setting. Continue

P a

S T S

to test weekly throughout the season.

Test Strips

12 Hour Pump Run Time 24 Hour Pump Run Time

PUMP SIZE PUMP SIZE

1/2 hp 3/4 hp 1 hp 1 1/2 hp 1/2 hp 3/4 hp 1 hp 1 1/2 hp

4.5 4 3 5 3.5 3 2.5 4

5 4.5 4 5.5 4 3.5 3 4.5

5.5 5 4.5 4 4.5 4 3.5 5

6 5.5 5 4.5 5 4.5 4 3.5

NR 6 5.5 5 5.5 5 4.5 4

RECOMMENDED FLOW RATE: 20-60 gpm

Above Grd.

POOL SIZE

llo

12,000 (24')

15,000

o n

d a

7,000 (18')

9,000 (21')

20,000

1/2 hp 3/4 hp 1 hp 1 1/2 hp

If using another means of chlorine support

Follow steps 1-5 on page 5 then continue below.

* *

8 Hour Pump Run Time

PUMP SIZE

5 4.5 4 3.5

5.5 5 4.5 4 6 5.5 5 4.5

NR 6 5.5 5

NR NR 6 5.5

Most common pool sizes

12 Hour Pump Run Time 24 Hour

1/2 hp 3/4 hp 1 hp 1 1/2 hp

4.5 4 3 5 3.5

5 4.5 4 5.5 4 3

5.5 5 4.5 4 4.5

NR 6 5.5 5 5.5

PUMP SIZE

* *

• After each testing, adjust the dial

up by 1/2 increment if the free chlorine reading has dropped

below 0.5 ppm or adjust down by 1/2 increment if the reading has risen above 1.0 ppm. Continue this process each day until the free chlorine reading stabilizes to at least 0.5 ppm.

• Remember to adjust dial ONLY by 1/2 setting per day in

order to prevent over chlorination which may bleach pool surfaces.

• Shock pool every two weeks or as

needed to maintain water quality. Follow label directions on the shock treatment used.

• Do not add shock in or near the

skimmer or into the POOL FROG Cycler as it could damage equipment, risk potential explosion or discolor your pool surface.

• Set dial to Setting 10.

Maintain a minimum chlorine reading of 0.5 ppm with a chlorine delivery device or hand feeding.

• Shock pool every two weeks or as

needed to maintain water quality. Follow label directions on the shock treatment used.

• Do not add shock in or near the

skimmer or into the POOL FROG® Cycler as it could damage equipment, risk potential explosion or discolor your pool surface.

Page 7

Replacing a POOL FROG

Mineral Reservoir

(POOL FROG® Mineral Reservoirs MUST be Replaced Every Season)

ABOVE GROUND 6100 (Order #01-12-6112)

NOW FITS THE FOLLOWING CYCLERS:

POOL FROG Series 5100, 5200 or 6100 Prevail Series 5770 or 5771

• Check the front of the box and back label of product to

make sure you have the correct POOL FROG® Mineral Reservoir to fit your POOL FROG® Cycler.

THE POOL FROG REPLACED EVERY 6 MONTHS OR AFTER ONE POOL SEASON WHICHEVER IS SHORTER

MINERAL RESERVOIR MUST BE

Open the box and remove the POOL FROG® Mineral Reservoir.

• IMPORTANT: Remove and read the

information card.

Please note: Complete instructions for inserting a POOL FROG Reservoir, FROG BAM® and POOL FROG® Bac Pac are included inside the POOL FROG box.

7422906 06101

Mineral

Mineral Reservoir

• Turn off pump and turn dial

to Setting 0. This reduces the flow of water into the unit when the cap is open.

• Open cap. If using POOL

FROG® Bac Pac stand back to avoid inhaling chlorine fumes.

CAUTION read carefully

• USE ONLY the factory recommended replacement

POOL FROG FROG® Bac Pac. DO NOT USE any other pac or bulk chemical tablets in the POOL FROG® Cycler. Use of any other product could result in damage to pool equipment or surface, unsafe pool conditions, fire or explosion. Warranty will be void if the correct POOL FROG FROG BAM® and POOL FROG® Bac Pac are not used.

Mineral Reservoir, FROG BAM

Mineral Reservoir,

and POOL

SLOT IN POOL FROG MINERAL RESERVOIR

FIN INSIDE OF POOL FROG CYCLER

• Find slot on side of

POOL FROG

Mineral Reservoir and line up with fin inside the POOL FROG® Cycler. Lower POOL FROG

Mineral Reservoir into POOL FROG® Cycler until secure.

Page 8

Replace FROG BAM® for an Algae Protection Guarantee

If you are not replacing FROG BAM®, proceed to Step 15. See FROG BAM

product labeling for complete directions

for use (EPA Reg. No. 53735-9).

• Remove cap from

FROG BAM® without removing seal.

90 DAY ALGAE PROTECTION

• Insert upside down into

center of POOL FROG

Mineral Reservoir pushing down firmly on key inside POOL FROG® Cycler to puncture seal on FROG BAM® bottle.

For a preventive dose add:

•

One FROG BAM

•

Two FROG BAM® for pools between 15,000 and 30,000 gallons.

11.

for pools up to 15,000 gallons

• Turn pump on for 90

minutes allowing FROG BAM® to circulate through pool.

12.

• To remove FROG BAM

turn pump off. Turn dial to Setting 0.

13.

10.

• Replace cap by hand only.

DO NOT OVER TIGHTEN.

•

Turn control dial on POOL

FROG® Cycler to Setting 10.

14.

• Remove POOL FROG

Cycler cap.

• Lift FROG BAM

up and allow any water in the container to drain through

0 D A

A L G

E P R

T E C

T I O

the POOL FROG® Cycler before discarding in trash.

NOTE: If water shows more than a hint of blue inside POOL FROG

Cycler, replace the POOL FROG® Cycler cap, turn dial to Setting 10 and run the pump for one minute.

14a. If pool size requires additional FROG

BAM

repeat steps 7-14.

14b. When water is clear in POOL FROG

Cycler,

proceed to step 15.

Page 9

Replacing POOL FROG® Bac Pac

15.

16.

Colored caps

• POOL FROG

Bac Pac recommended to assure up to 50% reduction in chlorine use*. POOL FROG® Bac Pac sold separately. (EPA Reg. No. 53735-2)

Compared to the minimum EPA recommended chlorine level of 1.0 ppm for a stabilized swimming pool.

• Avoid sparks, open flame

or smoking when handling the POOL FROG

Bac Pac.

19.

20.

• Line up the small leg of the

POOL FROG® Bac Pac with the small opening in the POOL

FROG the large leg with the large opening. Lower POOL FROG Bac Pac into POOL FROG

Mineral Reservoir and

Mineral Reservoir until secure.

POOL FROG MINERAL RESERVOIR

POOL FROG

BAC PAC

17.

18.

PAC

TOWERS

PAC TOWERS

• To remove POOL

FROG® Bac Pac colored caps, grab on to the lip of one cap with a pliers and pull up until cap releases. Repeat the process for the other cap.

• Holding the POOL

FROG® Bac Pac over the POOL FROG

Mineral Reservoir turn POOL FROG® Bac Pac over and shake slightly until chlorine tablets fall into tower areas.

• Replace cap by hand only.

DO NOT OVER TIGHTEN.

21.

• Mark your calendar for the six month replacement of the

POOL FROG FROG BAM® and approximate replacement times for the POOL FROG® Bac Pac. Once wetted, the time-released mineral coating of the POOL FROG effective up to 6 consecutive months or one pool season whichever is shorter. After that time, even if you hear the spent media inside, it is no longer effective and must be replaced.

Mineral Reservoir, 90-day replacement of

Mineral Reservoir is

Page 10

Troubleshooting

For more in-depth troubleshooting, go to www.kingtechnology.com

Problem Remedy

What do I do

if the water looks cloudy?

What do I do

if the water turns color?

What do I do

if algae forms in or on my pool?

1. Make sure your filtration system is working properly (i.e. clean filter, skimmer and pump basket).

2. Make sure circulation time is adequate – increase pump time if not.

1. Metals in the fill water may have been oxidized. Have the pool tested. Shock the pool and clean the filter until water clarity returns.

1. Use a nonmetallic (polyquat) algaecide per the directions on the bottle and brush the sides of the pool often.

2. Clean the filter and shock the pool with chlorine daily until water clarity returns.

3. Make sure the pool is properly balanced (see page 4).

4. Shock the water to eliminate build up of any organic matter.

2. Algae may be trying to form – shock the pool, increase circulation time if needed and clean the filter.

3. If you are in an area of the country that struggles with algae growth, see your dealer regarding a 90-day Algae Protection Guarantee using FROG BAM

hang tag for guarantee details.

. See product

5. Make sure pool has a free chlorine reading of

0.5 to 1.0 ppm.

6. Check with your dealer for more information.

3. Check with your dealer for more information.

4. Check with your dealer for more information.

What do I do

if I am under chlorinating with

POOL

the FROG

What do I do

if I am over chlorinating with

POOL FROG

the Bac Pac?

Bac Pac?

1. If you are unable to maintain

0.5 to 1.0 ppm, first make sure there are chlorine tablets in the tower areas of the POOL FROG Bac Pac and it is installed properly. If a correction was made, test the water in 24 hours.

2. If still low, turn the dial up one setting and test the water again in 24 hours. Continue

1. If the chlorine reading is over

3.0 ppm, remove the POOL

FROG FROG

the water daily until the reading is down to 1.0 ppm.

2. Reinsert the POOL FROG Pac, lower the dial one setting and test the water again in 24 hours.

Bac Pac from the POOL

Mineral Reservoir and test

raising the setting by one increment each day until the proper reading is achieved.

3. Shock the pool if the reading has been lower than 0.5 ppm for more than one day.

4. Bleed air by unscrewing the knob in the back of the POOL

Bac

FROG is running.

Cycler while the pump

If the reading has risen, lower the dial one setting again. Continue this process until proper reading is achieved.

3. If over-chlorinating at the lowest possible setting, consider decreasing the circulation time. Depending on your pump size,

5. Increase pump time if possible.

6. Contact your dealer to have your back pressure tested to ensure it is between 3 & 8 psi.

7. Contact King Technology’s Customer Service Department at 800-222-0169.

you may be circulating the water more than is necessary which results in more chlorine than is necessary.

4. Contact King Technology’s Customer Service Department at 800-222-0169.

Page 11

Parts List Model 6100/6500

8 & 9

CYCLER DIAGRAM/PARTS LIST • Model 6100 or 6500

REF. # PART NO. DESCRIPTION QTY. REQ.

1 & 2 01-22-1418 Cap w/O-Ring 1 2 01-22-1920 Cap O-Ring 1 3 N/A Body 1 4 01-22-9480 Pressure Relief Valve 1 5, 6, 7 01-22-1443 Control Dial with O-Rings and Locking Pin 1 6 01-22-1450 Control Dial O-Ring Set 1 7 N/A Control Dial Locking Pin 1 8 & 9 01-22-9940 Knob with O-Ring 2 10 01-22-9971 Silicone Lubricant 1 11 01-22-1710 Nipple Kit 1 12 01-22-1480 Mounting Base 1

Page 12

POOL FROG® Cycler Maintenance

Replacing the Control Dial O-Rings

Center of locking pin

• In the back of the POOL

FROG® Cycler depress center of locking pin with a finger and pull pin out of dial.

• Turn control dial back and

forth as you pull it out of the housing.

Replacing Cap O-Ring

• Hold cap in front of you

upside down with the o-ring groove facing up. Place one end of o-ring into cap groove at the point closest to you. Hold o-ring down with the thumb and forefinger of one hand.

• Take hold of the far end of

the o-ring with the thumb and index finger of the other hand. Roll o-ring slightly back towards you as you stretch the o-ring into the remainder of the cap groove.

C O

• Replace both o-rings. Apply

silicone lubricant that came with your POOL FROG® Cycler on

o-rings.

• Lubricate o-ring often with

silicone lubricant that came with your POOL FROG

Cycler. DO NOT USE petroleum based lubricants.

Replacing knob

• Carefully insert control dial

back into housing.

Back of POOL FROG Cycler

• Replace locking pin by

pushing it through the slots on the dial until it locks into place.

Front of POOL

FROG Cycler

•

o replace, simply unscrew old knob and replace with the new one.

Page 13

Winterizing

• Turn pump off and turn

dial to Setting 0.

• If POOL FROG

contains chlorine, wrap in plastic bag and store in shed or cool, well-ventilated location away from children, pets, motorcycles, cars or anything metal that can rust, pit, etc. Make sure POOL FROG® Bac Pac is away from open flame.

• Remove the POOL FROG

Mineral Reservoir and discard in trash. Even if you hear spent minerals inside, it is no longer effective.

Bac Pac still

• Remove cap.

• Unscrew knob from the

front of POOL FROG Cycler. Allow all water to drain.

• Replace the cap and knob

loosely.

Page 14

TOOLS NEEDED

Screwdriver

Pipe Wrench

Above Ground Filter Installation

INCLUDED WITH POOL FROG® CYCLER

Pipe Thread Tape

One 6" PVC Nipple

MATERIALS NEEDED

One Hose Adapter 1 1/2"

One Section of 1 1/2" Flex Hose (provided with filter)

1 1/2" TBE

1 1/2" X 1 1/4"

Apply pipe thread tape to each threaded end of nipple.

Apply pipe thread

tape to threaded end of hose adapter.

Screw one end of nipple into the filter return.

Tighten turning 1 to 2 revolutions with wrench. DO NOT OVER TIGHTEN.

Screw adapter into the other

side of POOL FROG

Tighten turning 1 to 2 revolutions with wrench.

DO NOT OVER TIGHTEN.

Cycler.

Screw either side of POOL FROG® Cycler on to open nipple end until upright and secure.

Bi-flow valve design allows water flow in either direction.

One Hose Clamp

RECOMMENDED

Corrosion Resistant Check Valve

HOSE ADAPTER

Attach return section of hose to the adapter with clamp. Tighten clamp with screwdriver.

If using a POOL FROG Pac, installing a corrosion resistant check valve is recommended.

Bac

Page 15

TOOLS NEEDED

Screwdriver

Above Ground, Base Installation

PUMP

Pipe Wrench

MATERIALS NEEDED

Pipe Thread Tape

Two Hose Adapters

1 1/2"

1 1/2" X 1 1/4"

Two Sections of 1 1/2" Flex Hose (one provided with filter)

Two Hose Clamps

RECOMMENDED

Corrosive Resistant Check Valve

1 1/4" Phillips

#10 Pan Head Screws with Washers

FILTER

Apply pipe thread tape to

the threaded end of both hose adapters.

Attach the filter section of

flex hose to one hose adapter and the return section of flex hose to the other hose adapter with clamps and tighten with screwdriver.

The POOL FROG® Cycler should always be installed between the filter and pool (or between heater and pool if applicable).

TO POOL

Screw adapters into each end of POOL FROG

Cycler. Tighten turning 1 to 2 revolutions with wrench.

DO NOT OVER TIGHTEN.

Bi-flow valve design allows water flow in either direction.

OPTION

1 1/2" Male Adaptor (slip X MPT)

When installing with hard PVC pipe, use a male adapter on the inside port threads.

HOSE

1 1/2"

CLAMP

FILTER & PUMP

If using a POOL FROG

X 1 1/2" X 1 1/4"

HOSE ADAPTER

1 1/2" OR 1 1/4" FLEX HOSE

HOSE CLAMP

Bac Pac installing a corrosion resistant

check valve is recommended.

HOSE ADAPTER

HOSE CLAMP

TO POOL

For better stability, POOL

FROG mounted on a base using Phillips pan head screws. One in front and two in back.

Cycler may be

Page 16

POOL FROG® Cycler Two-Year Limited Warranty

King Technology, Inc. warrants to the original purchaser this unit will be free from any defects in workmanship and/or material, for a period of two (2) years from the date of original purchase. This warranty covers body, cap and control dial, but specifically excludes o-rings. King Technology at its option may replace any defective parts or the entire unit without charge after it is determined what is needed to correct any deficiency. Replacement parts with the exception of o-rings are warranted for the remainder of the original warranty. To extend the limited warranty from two years to ten years, simply complete the warranty card that came with your unit and return it to King Technology within 30 days of purchase and installation.

1. To obtain warranty service, you must deliver the unit to King Technology or its nearest authorized dealer. Shipping expenses are the purchaser's responsibility. The name of the nearest authorized dealer can be obtained by writing or calling King Technology at the address and telephone number provided below. Proof of purchase is required when requesting warranty service. Purchaser must present the sales receipt or other documentation verifying proof of purchase.

2. This warranty does not cover defects caused by: Modification, alteration, repair or service of the unit contrary to the accompanying instructions; physical abuse to or misuse of the product or operation or installation in a manner contrary to the accompanying instructions. This warranty also excludes all costs arising from the installation, adjustment, removal or replacement of defective units or parts. This warranty also excludes any and all claims arising out of the chemicals used in the product or their characteristics.

3. CAUTION - Read carefully – Failure to follow these instructions will void the warranty. Do not add shock in or near skimmer.

A. This unit is not designed for shock treatment of pools. See your pool dealer or distributor for further information concerning shock treatments.

B. Control dial settings higher than needed can result in excess sanitizers being discharged into the pool. If the sanitizer level goes unmonitored, it can result in bleaching or discoloration of areas around the pool inlet or in some cases bleaching or discoloration of the entire pool liner or paint.

C. Excess trichlor in the pool can create health hazards to bathers. Consult each chemical manufacturer's warnings and cautions for specifics.

D. Misuse or failure to use the proper POOL FROG Reservoir and POOL FROG

Bac Pac may cause damage to

Mineral

equipment or personal injury. This warranty will be null and void, if this unit is not used with the recommended POOL FROG Mineral Reservoir and POOL FROG® Bac Pac.

4. This warranty is the exclusive warranty for the POOL FROG

Cycler. This warranty is not transferable. KING TECHNOLOGY MAKES NO REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER MATTER CONCERNING THE POOL FROG

CYCLER. Any express warranty not provided herein, and any remedy for breach of contract but which for this provision might arise by implication or operation of law is hereby excluded and disclaimed. THE EXCLUSIVE REMEDY FOR ANY CUSTOMER IS THE REPAIR OR REPLACEMENT OF THE UNIT, AND THE RECOVERY OF DAMAGES WILL NOT EXCEED THE PURCHASE PRICE OF THE UNIT. IN NO EVENT WILL KING TECHNOLOGY BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL OR PUNITIVE DAMAGES FROM ANY CAUSE.

5. Under no circumstance shall King Technology be liable to purchaser or any other person for any damage or loss incurred because of any chemicals used in the product or their physical characteristics, or interruption of service of the product, or any resulting special, incidental or consequential damages or losses. Some states do not allow the exclusion or limitation of incidental consequential damages, so the above limitation or exclusion may not apply to you.

Manufactured by: KING TECHNOLOGY, INC. 530 11th Avenue South, Hopkins, MN 55343 U.S.A. 952-933-6118

• 800-222-0169 • FAX 952-933-2206 www.kingtechnology.com

Made in U.S.A.

Covered by one or more of the following U.S. Patent Numbers: 4,662,387; 5,076,315; 5,218,983; 6,190,547; 6,210,566; 6,217,892; 6,383,507; 6,544,415; 6,551,609; 6,652,871 and other U.S. and Foreign Patents Pending.

20-48-0151E

553100643R3N