AQUA SMARTE
ABOVE GROUND
MINERAL SYSTEM FOR POOLS
Patented Mineral Pool Sanitizer
THE AQUA SMARTE
MINERAL RESERVOIR
MUST BE REPLACED
EVERY SIX MONTHS OR
AFTER ONE POOL
SEASON WHICHEVER
IS SHORTER.
®
Only the AQUA
SMARTE® Mineral
Reservoir fits the
AQUA SMARTE
Cycler
Instruction Manual
Customer Service 800-222-0169
®
TABLE OF CONTENTS
AQUA SMARTE® Introduction 3
Swimming Pool Tips 4
Start-up and Operation 5-6
Replacing AQUA SMARTE® Mineral Reservoir 7
®
Replacing AQUA SMARTE
Troubleshooting 9
Parts List 10
Replacing Control Dial O-Rings 11
Bac Pac 8
Replacing Cap O-Ring and Knob 11
Winterizing 12
Above Ground Filter Installation 13
Above Ground Base Installation 14
Warranty 15
For information on King Technology’s entire product line, visit
our website at www.kingtechnology.com
AQUA
SMARTE
Welcome to easier pool care courtesy of AQUA SMARTE®. With AQUA
®
,
SMARTE
work or a lot of chlorine.
®
your pool water will look and feel better without a lot of
This system controls bacteria using a
combination of minerals and reduced chlorine levels-up to 50%* less.
®
There are 3 parts to the AQUA SMARTE
®
AQUA SMARTE
the AQUA SMARTE
Cycler, the AQUA SMARTE® Mineral Reservoir and
®
Bac Pac.
System: The Above Ground
Part 1
®
AQUA SMARTE
The water treatment center that controls the flow of
water to each part of the AQUA SMARTE® System.
Cycler
For Above Ground Pools
up to 25,000 gallons.
Part 2
®
AQUA SMARTE
Holds the minerals and fits inside the AQUA SMARTE® Cycler.
THE AQUA SMARTE® MINERAL RESERVOIR MUST BE
REPLACED EVERY SIX MONTHS OR AFTER ONE POOL
SEASON WHICHEVER IS SHORTER.
to
%
0
5
f a
o
d
e
s
re
u
u
n
s
s
tio
a
c
e
u
b
d
o
T
re
e
ith
rin
lo
ir w
h
o
c
rv
%
e
s
0
8
e
l R
ra
e
.
in
c
a
M
P
is
h
c
t
a
B
e
rin
lo
h
c
a
e
tiv
a
rn
lte
a
n
a
ly
p
ith
im
w
s
g
e
in
s
rin
lo
If u
h
f c
e
o
e
f th
rc
r o
u
o
te
s
n
e
ty
c
p
e
m
th
e
ir e
v
o
a
rv
le
e
l
s
e
ia
l R
l d
ra
e
tro
n
in
o
M
c
e
t th
e
s
d
n
.
a
m
u
im
x
a
m
to
g
in
th
y
n
t a
u
t p
e
o
in
n
o
M
D
e
f th
r o
a
te
n
r th
e
e
c
th
ir o
o
rv
e
th
s
e
to
R
e
g
a
m
a
. D
o
c
a
t c
P
n
e
m
ip
u
q
r e
w
o
ty
n
rra
a
w
d
n
.
a
id
o
v
d
n
ll a
u
n
Mineral Reservoir
e
th
in
l
ra
c
a
B
a
n
l
o
o
p
e
lt
u
s
re
ld
u
e
b
ld
u
o
(AQUA SMARTE
Compared to the minimum EPA recommended chlorine level of 1.0 ppm for a stablized swimming pool.
*
Part 3
®
AQUA SMARTE
Pre-filled with chlorine tablets and
fits inside AQUA SMARTE
Reservoir.
®
Mineral Reservoir sold inside AQUA SMARTE® Cycler and separately for replacements.
AQUA SMARTE
Bac Pac
®
Mineral
®
Bac Pac sold separately.)
Swimming Pool Tips
Start-up and Yearly Maintenance
1.
• Make sure the pool has adequate circulation. The pool
water must completely circulate through the pump and
filter at least 1 to 2 times per day. This usually requires 8
to 12 hours. Check with your dealer for the proper circulation
time for your pool.
2.
3.
• If your fill water is high in metals, use a sequestering agent
or metal out product at start-up only before using the AQUA
SMARTE® Mineral Reservoir. See your local dealer for
details on using these products and always follow
manufacturers directions carefully.
•After your pool is up and running
smoothly, continue to test your
4.
water for pH, total alkalinity and
chlorine and maintain its balance
by adding any necessary
adjustment products (see your
dealer for details).
• Before beginning with any pool care program, you must
first balance your pool water. Take a water sample to your
local pool professional or use a complete test kit that will
test for the following important elements.
Water Balance Guidelines
pH: 7.2 — 7.8
Total Alkalinity: 60 — 120 ppm
Calcium Hardness: 150 — 400
Total Dissolved Solids: <1500
Stabilizer: 20 — 80 ppm
Free Chlorine: 0.5 — 1.0 ppm
5.
• Check the pool's filter gauge often and periodically clean
filter per the manufacturer's directions. A dirty filter will slow
the flow of water which could hamper proper circulation.
Start-up and Operation
1.
2.
• Add a stabilizer or conditioner to
the pool at the beginning of the
season if the stabilizer level is below
20 ppm. This will prevent chlorine
burn off. Follow manufacturer’s
directions carefully.
• Shock the pool with chlorine to rid
the water of all contaminants before
beginning with AQUA SMARTE
Follow manufacturer's directions
carefully.
• THIS STEP IS VERY IMPORTANT
TO START-UP.
USE CHLORINE SHOCK ONLY.
®
.
4.
5.
• Replace cap and run AQUA
SMARTE® Cycler, with AQUA
SMARTE
inserted, for 10 minutes on Setting
10.
• When chlorine reading is down
to 1.0 ppm, which may take a few
days, insert AQUA SMARTE
Pac. (
®
Mineral Reservoir
®
Bac
Follow directions on page
8.)
• Do not add shock in or near the skimmer or into the
AQUA SMARTE
potential explosion or discolor your pool surface.
3.
®
Cycler as it could damage equipment, risk
• Install a AQUA SMARTE
Reservoir into the AQUA SMARTE
Cycler. (Follow directions on page 7.)
REPLACE THE AQUA SMARTE
MINERAL RESERVOIR EVERY
6 MONTHS OR AFTER ONE POOL
SEASON WHICHEVER IS
SHORTER.
®
Mineral
®
®
Start-up and Operation
u
• Set control dial by matching up the parameters of your pool on the chart below. THIS IS A
7.
STARTING POINT ONLY and may need to be adjusted to fit your individual pool needs. See #8
for directions. IMPORTANT: Pump run times less than 8 hours could result in under chlorination due
to inadequate flow through the System.
4
Above Grd.
POOL SIZE
G
a
llo
n
s
D
ia
m
7,000 (18')
9,000 (21')
12,000 (24')
15,000
20,000
e
te
r
1/2 hp 3/4 hp 1 hp 1 1/2 hp
8 Hour Pump Run Time
PUMP SIZE
5 4.5 4 3.5
5.5 5 4.5 4
6 5.5 5 4.5
NR 6 5.5 5
NR NR 6 5.5
* – Bypass installation recommended.
NR – This pump size is not recommended for this size pool.
Find your starting dial setting by matching up the
parameters of your pool on the above chart. An above
ground pool with approximately 12,000 gallons with a
1 horse pump running 12 hours a day would require a
starting setting of 4.5. See example at right.
• For the first week test the
8.
pool water daily for free chlorine
ensure correct dial setting. Continue
P
a
S
T
S
to test weekly throughout the season.
Test Strips
12 Hour Pump Run Time 24 Hour Pump Run Time
PUMP SIZE PUMP SIZE
1/2 hp 3/4 hp 1 hp 1 1/2 hp 1/2 hp 3/4 hp 1 hp 1 1/2 hp
4.5 4 3 5 3.5 3 2.5 4
5 4.5 4 5.5 4 3.5 3 4.5
5.5 5 4.5 4 4.5 4 3.5 5
6 5.5 5 4.5 5 4.5 4 3.5
NR 6 5.5 5 5.5 5 4.5 4
RECOMMENDED FLOW RATE: 20-60 gpm
Above Grd.
POOL SIZE
G
s
a
n
llo
m
ia
e
D
e
t
r
7,000 (18')
9,000 (21')
12,000 (24')
15,000
20,000
l
o
o
n
d
a
p
t
s
e
s
p
i
t
r
1/2 hp 3/4 hp 1 hp 1 1/2 hp
If using another means of chlorine support
Follow steps 1-5 on page 5 then continue below.
*
*
8 Hour Pump Run Time
PUMP SIZE
5 4.5 4 3.5
5.5 5 4.5 4
6 5.5 5 4.5
NR 6 5.5 5
NR NR 6 5.5
Most common pool sizes
12 Hour Pump Run Time 24 Hour P
1/2 hp 3/4 hp 1 hp 1 1/2 hp
4.5 4 3 5 3.5 3
5 4.5 4 5.5 4 3.5
5.5 5 4.5 4 4.5 4
NR 6 5.5 5 5.5 5
PUMP SIZE
*
*
*
*
*
• After each testing, adjust the dial
up by 1/2 increment if the free
chlorine reading has dropped
4
below 0.5 ppm or adjust down by
1/2 increment if the reading has
risen above 1.0 ppm. Continue this
process each day until the free
chlorine reading stabilizes to at
least 0.5 ppm.
• Remember to adjust dial ONLY by 1/2 setting per day in
order to prevent over chlorination which may bleach pool
surfaces.
9.
• Shock pool every two weeks or as
needed to maintain water quality.
Follow label directions on the shock
treatment used.
• Do not add shock in or near the
skimmer or into the AQUA SMARTE
Cycler as it could damage equipment,
risk potential explosion or discolor
you pool surface.
6.
• Set dial to Setting 10.
Maintain a minimum chlorine
reading of 0.5 ppm with a
chlorine delivery device or hand
feeding.
• Shock pool every two weeks or as
7.
®
needed to maintain water quality. Follow
label directions on the shock treatment
used.
• Do not add shock in or near the
skimmer or into the AQUA SMARTE
®
Cycler as it could damage equipment,
risk potential explosion or discolor you
pool surface.
Replacing a AQUA SMARTE
(
AQUA SMARTE
®
Mineral Reservoirs MUST be Replaced Every Season)
®
Mineral Reservoir
Only the AQUA SMARTE® Mineral Reservoir
1.
fits the AQUA SMARTE® Cycler.
CONTENTS:
Above Ground Series 6700
For use with the Aqua Smarte
Cycler Model 5720 or 6700
• Check the front of the box and back label of product to
make sure you have the correct AQUA SMARTE® Mineral
Reservoir to fit your AQUA SMARTE® Cycler.
®
THE AQUA SMARTE
MINERAL RESERVOIR MUST BE
REPLACED EVERY 6 MONTHS OR AFTER ONE POOL
SEASON WHICHEVER IS SHORTER
2.
Open the box and remove the AQUA
SMARTE® Mineral Reservoir.
• IMPORTANT: Remove and read the
information card.
to
%
0
5
f a
o
d
e
s
re
u
u
n
s
s
tio
a
c
e
u
b
d
o
T
re
e
ith
rin
lo
ir w
h
o
c
rv
%
e
s
0
8
e
l R
ra
e
.
in
c
a
M
P
is
c
th
a
B
e
rin
lo
h
c
a
e
tiv
a
rn
lte
a
n
a
ly
p
ith
im
w
s
g
e
in
s
rin
lo
If u
h
f c
e
o
e
f th
rc
r o
u
o
te
s
n
e
ty
c
p
e
m
th
e
ir e
v
o
a
rv
le
e
l
s
e
ia
l R
l d
ra
e
tro
n
in
o
M
c
e
t th
e
s
d
n
.
a
m
u
im
x
a
m
to
e
th
in
g
in
th
y
n
t a
u
l
ra
t p
e
o
in
n
o
M
D
e
a
B
f th
a
n
r o
a
te
n
r th
e
e
c
th
o
o
ir o
p
o
e
rv
e
th
s
e
to
R
e
g
a
re
m
a
ld
u
. D
o
c
a
t c
P
n
e
m
b
ip
ld
u
u
q
o
r e
w
o
ty
n
rra
a
w
d
n
.
a
id
o
v
d
n
ll a
u
n
Please note: Complete instructions for
inserting a AQUA SMARTE
Reservoir and AQUA SMARTE® Bac
Pac are included inside the AQUA
SMARTE
c
l
lt
u
s
e
®
Mineral Reservoir box.
®
Mineral
4.
• Turn off pump and turn dial
to Setting 0. This reduces the
flow of water into the unit
when the cap is open.
5.
• Open cap. If using AQUA
SMARTE® Bac Pac stand
back to avoid inhaling
chlorine fumes.
3.
CAUTION read carefully
• USE ONLY the factory recommended replacement
AQUA SMARTE
Bac Pac. DO NOT USE any other pac or bulk chemical
tablets in the AQUA SMARTE® Cycler. Use of any other
product could result in damage to pool equipment or surface,
unsafe pool conditions, fire or explosion. Warranty will be
void if the correct AQUA SMARTE
AQUA SMARTE® Bac Pac are not used.
7
®
Mineral Reservoir and AQUA SMARTE
®
Mineral Reservoir and
6.
SLOT IN AQUA
SMARTE
MINERAL
RESERVOIR
FIN INSIDE
OF AQUA
®
SMARTE
CYCLER
• Find slot on side of
AQUA SMARTE
®
Mineral Reservoir and
line up with fin inside
the AQUA SMARTE
Cycler. Lower AQUA
SMARTE
®
Mineral
®
Reservoir into AQUA
SMARTE® Cycler until
secure.
Replacing AQUA SMARTE® Bac Pac
1.
2.
Colored caps
• AQUA SMARTE
Pac recommended to
assure up to 50% reduction
in chlorine use*. AQUA
SMARTE® Bac Pac sold
separately.
(EPA Reg. No. 53735-2)
*
Compared to the minimum
EPA recommended chlorine
level of 1.0 ppm for a stabilized
swimming pool.
• Avoid sparks, open flame
or smoking when handling
the AQUA SMARTE® Bac
Pac.
®
Bac
5.
6.
• Line up the small leg of the
AQUA SMARTE® Bac Pac with
the small opening in the AQUA
SMARTE
the large leg with the large
opening. Lower AQUA SMARTE
Bac Pac into AQUA SMARTE
Mineral Reservoir until secure.
®
Mineral Reservoir and
AQUA
SMARTE
MINERAL
RESERVOIR
AQUA SMARTE
BAC PAC
®
®
3.
4.
PAC
TOWERS
PAC
TOWERS
• To remove AQUA
SMARTE® Bac Pac colored
caps, grab on to the lip of
one cap with a pliers and
pull up until cap releases.
Repeat the process for the
other cap.
• Holding the AQUA
SMARTE® Bac Pac over
the AQUA SMARTE
Mineral Reservoir turn
AQUA SMARTE® Bac Pac
over and shake slightly until
chlorine tablets fall into
tower areas.
®
• Replace cap by hand only.
DO NOT OVER TIGHTEN.
7.
• Mark your calendar for the six month replacement of the
AQUA SMARTE
replacement times for the AQUA SMARTE® Bac Pac. Once
wetted, the time-released mineral coating of the AQUA
SMARTE
months or one pool season whichever is shorter. After that
time, even if you hear the spent media inside, it is no longer
effective and must be replaced.
®
®
Mineral Reservoir and approximate
Mineral Reservoir is effective up to 6 consecutive
8
Troubleshooting
For more in-depth troubleshooting, go to www.kingtechnology.com
Problem Remedy
What do I do
1.
if the water looks
cloudy?
What do I do
2.
if the water turns
color?
What do I do
3.
if algae forms in
or on my pool?
1. Make sure your filtration
system is working properly (i.e.
clean filter, skimmer and pump
basket).
2. Make sure circulation time is
adequate – increase pump time
if not.
1. Metals in the fill water may
have been oxidized. Have the
pool tested. Shock the pool and
clean the filter until water clarity
returns.
1. Use a nonmetallic (polyquat)
algaecide per the directions on
the bottle and brush the sides of
the pool often.
2. Clean the filter and shock the
pool with chlorine daily until water
clarity returns.
3. Make sure the pool is properly
balanced (see page 4).
4. Shock the water to eliminate
build up of any organic matter.
2. Algae may be trying to form
– shock the pool, increase
circulation time if needed and
clean the filter.
3. If you are in an area of the
country that struggles with algae
growth, see your dealer for an
algae preventative.
5. Make sure pool has a
free chlorine reading of
0.5 to 1.0 ppm.
6. Check with your dealer for
more information.
3. Check with your dealer for
more information.
4. Check with your dealer for
more information.
What do I do
4.
if I am under
chlorinating with
the AQUA
SMARTE
Pac?
What do I do
5.
if I am over
chlorinating with
the AQUA
SMARTE
Pac?
®
Bac
®
Bac
1. If you are unable to maintain
0.5 to 1.0 ppm, first make sure
there are chlorine tablets in the
tower areas of the AQUA
SMARTE
installed properly. If a correction
was made, test the water in 24
hours.
2. If still low, turn the dial up
one setting and test the water
again in 24 hours. Continue
1. If the chlorine reading is over
3.0 ppm, remove the AQUA
SMARTE® Bac Pac from the
AQUA SMARTE
Reservoir and test the water daily
until the reading is down to
1.0 ppm.
2. Reinsert the AQUA SMARTE
Bac Pac, lower the dial one setting
®
Bac Pac and it is
®
Mineral
raising the setting by one
increment each day until the
proper reading is achieved.
3. Shock the pool if the reading
has been lower than 0.5 ppm
for more than one day.
4. Bleed air by unscrewing the
knob in the back of the AQUA
SMARTE
pump is running.
and test the water again in 24
hours. If the reading has risen,
lower the dial one setting again.
Continue this process until
proper reading is achieved.
3. If over-chlorinating at the
lowest possible setting, consider
®
decreasing the circulation time.
Depending on your pump size,
®
Cycler while the
5. Increase pump time if
possible.
6. Contact your dealer to have
your back pressure tested to
ensure it is between 3 & 8 psi.
7. Contact King Technology’s
Customer Service Department at
800-222-0169.
you may be circulating the water
more than is necessary
which results in more chlorine
than is necessary.
4. Contact King Technology’s
Customer Service Department
at 800-222-0169.
9
Parts List
1
2
8 & 9
3
4
11
7
10
10
O
?
T
Y
H
P
E
O
R
C
S
I
E
L
I
N
C
O
L
U
T
B
N
R
A
I
C
C
Y
O
P
C
Y
O
P
C
O
Y
P
C
Y
O
P
6
9
5
CYCLER DIAGRAM/PARTS LIST
REF. # PART NO. DESCRIPTION QTY. REQ.
1 & 2 01-22-1418 Cap w/O-Ring 1
2 01-22-1920 Cap O-Ring 1
3 N/A Body 1
4 01-22-9480 Pressure Relief Valve 1
5, 6, 7 01-22-1443 Control Dial with O-Rings & Locking Piin 1
6 01-22-1450 Control Dial O-Ring Set 1
7 N/A Control Dial Locking Pin 1
8 & 9 01-22-9940 Knob with O-Ring 2
10 01-22-9971 Silicone Lubricant 1
11 01-22-1710 Nipple Kit 1
12 01-22-1480 Mounting Base 1
8
12
AQUA SMARTE® Cycler Maintenance
Replacing the Control Dial O-Rings
1.
Center of locking pin
• In the back of the AQUA
SMARTE® Cycler depress
center of locking pin with a
finger and pull pin out of dial.
2.
• Turn control dial back and
forth as you pull it out of the
housing.
Replacing Cap O-Ring
1.
2.
• Hold cap in front of you
upside down with the o-ring
groove facing up. Place one
end of o-ring into cap groove
at the point closest to you.
Hold o-ring down with the
thumb and forefinger of one
hand.
• Take hold of the far end of
the o-ring with the thumb and
index finger of the other hand.
Roll o-ring slightly back
towards you as you stretch
the o-ring into the remainder
of the cap groove.
3.
4.
5.
O
?
T
Y
H
P
E
R
O
C
S
I
E
L
I
N
C
O
L
U
T
B
N
R
A
I
C
C
O
Y
P
C
O
Y
P
C
O
P
Y
C
O
Y
P
• Replace both o-rings. Apply
silicone lubricant that came with
your AQUA SMARTE® Cycler
3.
on o-rings.
x
x
x
x
x
S
L
E
I
N
C
O
L
U
T
B
N
R
A
I
C
C
Y
O
P
C
Y
O
P
C
O
Y
P
C
Y
O
P
• Lubricate o-ring often with
silicone lubricant that came
with your AQUA SMARTE
®
Cycler. DO NOT USE
petroleum based lubricants.
Replacing knob
• Carefully insert control dial
back into housing.
Back of
AQUA
SMARTE
Cycler
®
• Replace locking pin by
pushing it through the slots on
the dial until it locks into place.
Front of
AQUA
SMARTE
Cycler
®
11
•
T
o replace, simply unscrew
old knob and replace with the
new one.
Winterizing
1.
2.
• Turn pump off and turn
dial to Setting 0.
4.
5.
• If AQUA SMARTE
still contains chlorine, wrap in
plastic bag and store in shed or
garage away from children, pets,
motorcycles, cars or anything
metal that can rust, pit, etc.
Make sure AQUA SMARTE
Bac Pac is away from open
flame.
• Remove the AQUA
SMARTE
and discard in trash. Even if
you hear spent minerals inside,
it is no longer effective.
®
Mineral Reservoir
®
Bac Pac
®
3.
• Remove cap.
• Unscrew knob from the
front of AQUA SMARTE
Cycler. Allow all water to
drain.
6.
®
• Replace the cap and knob
loosely.
12
TOOLS NEEDED
Screwdriver
Pipe Wrench
Above Ground Filter Installation
INCLUDED WITH
AQUA SMARTE
CYCLER
Pipe Thread
Tape
One 6"
PVC Nipple
MATERIALS NEEDED
One Hose Adapter
1 1/2"
One Section of
1 1/2" Flex Hose
(provided with filter)
X
1 1/2" TBE
X
1 1/2" X 1 1/4"
1.
Apply pipe thread tape to
each threaded end of nipple.
Apply pipe thread
4.
tape to threaded end
of hose adapter.
2.
Screw one end of nipple
into the filter return.
Tighten turning
1 to 2 revolutions with wrench.
DO NOT OVER TIGHTEN.
Screw adapter into the other side
5.
of AQUA SMARTE
Tighten turning
1 to 2 revolutions
with wrench.
DO NOT
OVER TIGHTEN.
®
Cycler.
Screw either side of
3.
AQUA SMARTE® Cycler
on to open nipple end
until upright and secure.
Bi-flow valve
design allows
water flow in
either
direction.
One
Hose
Clamp
RECOMMENDED
Corrosion Resistant
Check Valve
13
HOSE ADAPTER
6.
Attach return section of hose
to the adapter with clamp.
Tighten clamp with
screwdriver.
7.
If using an AQUA SMARTE
Bac Pac, installing a
corrosion resistant check
valve is recommended.
®
TOOLS NEEDED
Screwdriver
Above Ground, Base Installation
PUMP
Pipe Wrench
MATERIALS NEEDED
Pipe Thread
Tape
Two Hose Adapters
X
1 1/2"
1 1/2" X 1 1/4"
Two Sections
of 1 1/2" Flex Hose
(one provided with filter)
Two
Hose
Clamps
RECOMMENDED
Corrosive Resistant
Check Valve
X
1 1/4" Phillips
#10
Pan Head Screws with
Washers
FILTER
Apply pipe thread tape to
1.
the threaded end of both
hose adapters.
Attach the filter section of
3.
flex hose to one hose
adapter and the return
section of flex hose to the
other hose adapter with
clamps and tighten with
screwdriver.
The AQUA SMARTE® Cycler should always be
installed between the filter and pool (or between
heater and pool if applicable).
TO POOL
Screw adapters into each end of AQUA SMARTE
2.
Cycler. Tighten turning 1 to 2 revolutions with wrench.
DO NOT OVER TIGHTEN.
Bi-flow valve design allows
water flow in either direction.
®
OPTION
1 1/2" Male Adaptor
(slip X MPT)
When installing with
hard PVC pipe, use a
male adapter on the
inside port threads.
14
HOSE
1 1/2"
CLAMP
FILTER &
PUMP
4.
If using an AQUA SMARTE
X 1 1/2" X 1 1/4"
HOSE ADAPTER
1 1/2" OR 1 1/4"
FLEX HOSE
HOSE
ADAPTER
HOSE
CLAMP
®
Bac Pac installing a corrosion
resistant check valve is recommended.
HOSE
ADAPTER
HOSE
CLAMP
TO POOL
5.
For better stability, AQUA
SMARTE
mounted on a base using
Phillips pan head screws. One
in front and two in back.
®
Cycler may be
AQUA SMARTE® Cycler Two-Year Limited Warranty
King Technology, Inc. warrants to the original purchaser this unit
will be free from any defects in workmanship and/or material, for
a period of two (2) years from the date of original purchase. This
warranty covers body, cap and control dial, but specifically excludes
o-rings. King Technology at its option may replace any defective
parts or the entire unit without charge after it is determined what
is needed to correct any deficiency. Replacement parts with the
exception of o-rings are warranted for the remainder of the original
warranty. To extend the limited warranty from two years to ten years,
simply complete the warranty card that came with your unit and
return it to King Technology within 30 days of purchase and
installation.
1. To obtain warranty service, you must deliver the unit to King
Technology or its nearest authorized dealer. Shipping expenses
are the purchaser's responsibility. The name of the nearest authorized
dealer can be obtained by writing or calling King Technology at the
address and telephone number provided below. Proof of purchase
is required when requesting warranty service. Purchaser must
present the sales receipt or other documentation verifying proof of
purchase.
2. This warranty does not cover defects caused by: Modification,
alteration, repair or service of the unit contrary to the accompanying
instructions; physical abuse to or misuse of the product or operation
or installation in a manner contrary to the accompanying instructions.
This warranty also excludes all costs arising from the installation,
adjustment, removal or replacement of defective units or parts. This
warranty also excludes any and all claims arising out of the chemicals
used in the product or their characteristics.
3. CAUTION - Read carefully – Failure to follow these instructions
will void the warranty. Do not add shock in or near skimmer.
A. This unit is not designed for shock treatment of pools. See
your pool dealer or distributor for further information concerning
shock treatments.
B. Control dial settings higher than needed can result in excess
sanitizers being discharged into the pool. If the sanitizer level
goes unmonitored, it can result in bleaching or discoloration
of areas around the pool inlet or in some cases bleaching or
discoloration of the entire pool liner or paint.
C. Excess trichlor in the pool can create health hazards to
bathers. Consult each chemical manufacturer's warnings and
cautions for specifics.
D. Misuse or failure to use the proper AQUA SMARTE
Reservoir and AQUA SMARTE
®
Bac Pac may cause damage to
®
Mineral
equipment or personal injury. This warranty will be null and
void, if this unit is not used with the recommended AQUA
SMARTE
®
Mineral Reservoir and AQUA SMARTE® Bac Pac.
4. This warranty is the exclusive warranty for the AQUA SMARTE
Cycler. This warranty is not transferable. KING TECHNOLOGY
MAKES NO REPRESENTATION OR WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, AS TO MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE OR ANY OTHER MATTER
CONCERNING THE AQUA SMARTE
®
CYCLER. Any express
warranty not provided herein, and any remedy for breach of contract
but which for this provision might arise by implication or operation
of law is hereby excluded and disclaimed. THE EXCLUSIVE REMEDY
FOR ANY CUSTOMER IS THE REPAIR OR REPLACEMENT OF
THE UNIT, AND THE RECOVERY OF DAMAGES WILL NOT
EXCEED THE PURCHASE PRICE OF THE UNIT. IN NO EVENT
WILL KING TECHNOLOGY BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, SPECIAL OR PUNITIVE DAMAGES FROM
ANY CAUSE.
5. Under no circumstance shall King Technology be liable to purchaser
or any other person for any damage or loss incurred because of any
chemicals used in the product or their physical characteristics, or
interruption of service of the product, or any resulting special,
incidental or consequential damages or losses. Some states do not
allow the exclusion or limitation of incidental consequential damages,
so the above limitation or exclusion may not apply to you.
®
Covered by one or more of the following U.S. Patent Numbers: 4,662,387;
5,076,315; 5,218,983; 6,190,547; 6,210,566; 6,217,892; 6,383,507; 6,544,415;
6,551,609; 6,652,871 and other U.S. and Foreign Patents Pending.
Manufactured by: KING TECHNOLOGY, INC.
530 11th Avenue South, Hopkins, MN 55343 U.S.A.
952-933-6118 • 800-222-0169 • FAX 952-933-2206 www.kingtechnology.com
15
Made in U.S.A.
20-48-0153E
553100643R3N
Loading...