King Technology 5450 User Manual

Download

Pool FROG

XL PRO In GROUND

MINERAL SYSTEM FOR POOLS

Patented Mineral Pool Sanitizer

THE POOL FROG

MINERAL RESERVOIR

MUST BE REPLACED

EVERY SIX MONTHS

OR AFTER ONE POOL

MINERAL

RESERVOIR

CHLORINE

PAC

SEASON WHICHEVER

IS SHORTER.

Model 5450

Instruction Manual

Customer Service 800-222-0169

POOL FROG

Swimming Pool Tips 4

Start-up and Operation 5

Replacing POOL FROG

Introduction 3

Mineral Reservoir 7

Replacing FROG BAM

Replacing POOL FROG

Pac 9

Troubleshooting 10

Parts List 11

Replacing Control Dial O-Rings 12

Replacing Cap O-Ring and Knob 12

Winterizing 13

In-line Installation 14

For Proper Performance 15

Warranty 16

For information on King Technology’s entire product line, visit our website at www.kingtechnology.com

POOL FROG

Welcome to easier pool care courtesy of POOL FROG® XL PRO. With POOL FROG XL PRO, your pool water will look and feel better without a lot of work or a lot of chlorine.

chlorine levels. There are 5 parts to the POOL FROG® XL PRO System: Two In Ground Cyclers, the POOL FROG Preventative and the POOL FROG

This system controls bacteria using a combination of minerals and reduced

Mineral Reservoir, FROG BAM

Pac.

90-day Algae

Part I

POOL FROG

The water treatment centers that control the flow of water through the POOL FROG® Mineral Reservoir in one and the POOL FROG® Pac in the other.

MINERAL

RESERVOIR

XL PRO Cyclers

CHLORINE

PAC

Part II

POOL FROG

Mineral Reservoir

Holds the minerals and fits inside the POOL FROG® Mineral Cycler.

ineral

L FRO

ith the

sed

est results, the PO

be u

uld

For b Reservoir sho

chlorine Bac Pac.

ove the

ply rem

Sim

tabs on the Bac

colored

ir.

insert into the Pac and center of the Reservo

ur size

r yo

ial fo

and

Set the d

er day

l, size p

e p

-run tim

aintain a

rine

just to

chlo

and

1 p

.5 to

anual).

low

level (see m

from

or eq

o not put anything else into the center

ineral Reservo

of the M

logy or d

result.

King Techno

ent could

uip

l has an alternate source

hlorinator, floater or

If the p

rine (a c f chlo o

ing), a Flow

feed

in the center o

hand

laced

ensure go

ir to

ust be p

ugh the m

ineral Reservo

thro

ater flo

a Flow

u need

If yo

lease call 1-800-222-0169

before you use the p

BAM copy to come

ut a Bac Pac

ir b

age to the

l Pac

ntro

f the od

inerals.

l Pac,

ntro

uct.

rod

THE POOL FROG® MINERAL RESERVOIR

MUST BE REPLACED EVERY SIX MONTHS OR AFTER ONE POOL SEASON WHICHEVER IS

POOL FROG

Mineral Cycler

Part III FROG BAM

Use with the POOL

FROG for an Algae-Protection Guarantee.

XL PRO System

(POOL FROG

SHORTER.

For In Ground Pools

up to 40,000 gallons.

POOL FROG

Chlorine Cycler

Part IV

POOL FROG

Chlorine support fits inside POOL FROG® Chlorine Cycler.

Mineral Reservoir sold inside POOL FROG® Mineral Cycler and separately for replacements.

POOL FROG

Pac and FROG BAM® sold separately.)

Pac

PAC

Swimming Pool Tips

Start-up and Yearly Maintenance

• Make sure the pool has adequate circulation. The pool

water must completely circulate through the pump and filter at least 1 to 2 times per day. This usually requires 8 to 12 hours. Check with your dealer for the proper circulation time for your pool.

• If your fill water is high in metals, use a sequestering agent

or metal out product at start-up only before using the POOL FROG® Mineral Reservoir. See your local dealer for details on using these products and always follow manufacturers directions carefully.

•After your pool is up and running

smoothly, continue to test your water for pH, total alkalinity and

chlorine and maintain its balance by adding any necessary adjustment products (see your dealer for details).

• Before beginning with any pool care program, you must

first balance your pool water. Take a water sample to your local pool professional or use a complete test kit that will test for the following important elements.

Water Balance Guidelines

pH: 7.2 – 7.8 Total Alkalinity: 60 – 120 ppm Calcium Hardness: 150 – 400 Total Dissolved Solids: <1500 Stabilizer: 20 – 80 ppm Free Chlorine: 0.5 – 1.0 ppm

• Check the pool's filter gauge often and periodically clean

filter per the manufacturer's directions. A dirty filter will slow the flow of water which could hamper proper circulation.

Start-up and Operation

• Add a stabilizer or conditioner to

the pool at the beginning of the season if the stabilizer level is below 20 ppm. This will prevent chlorine burn off. Follow manufacturer’s directions carefully.

• Shock the pool with chlorine to rid

the water of all contaminants before beginning with POOL FROG

XL PRO. Follow manufacturer's directions carefully.

• THIS STEP IS VERY IMPORTANT

TO START-UP. USE CHLORINE SHOCK ONLY.

POOL FROG

Mineral Cycler

• Replace cap and set dial on

POOL FROG

Mineral Cycler to

Maximum.

• For an Algae

Protection Guarantee insert FROG BAM

POOL FROG® Mineral Reservoir in POOL

FROG

Mineral Cycler.

(See page 8 for directions.)

POOL FROG

Chlorine

Cycler

into

POOL FROG

Mineral Cycler

POOL FROG

Chlorine

Cycler

• Do not add shock in or near the skimmer or into the POOL

FROG® XL PRO Cyclers as it could damage equipment, risk potential explosion or discolor your pool surface.

POOL FROG Mineral Reservoir

• Install a POOL FROG

Mineral Reservoir into the POOL FROG® Mineral Cycler. (Follow Directions on Page 7.)

REPLACE THE POOL

POOL FROG

Mineral Cycler

RESERVOIR EVERY 6 MONTHS OR AFTER

FROG

MINERAL

ONE POOL SEASON WHICHEVER IS

Cycler

SHORTER.

POOL FROG

Mineral Cycler

POOL FROG

Chlorine

POOL FROG

Pac

POOL FROG

Mineral Cycler

POOL FROG

Chlorine

Cycler

Insert a POOL

FROG

the

Pac into

POOL FROG

Chlorine Cycler.

Start-up and Operation

• Set control dial on POOL FROG

the chart below. THIS IS A STARTING POINT ONLY and may need to be adjusted to fit your individual

Chlorine Cycler by matching up the parameters of your pool on

pool needs. See #8 for directions. IMPORTANT: Pump run times less than 8 hours could result in

under chlorination due to inadequate flow through the System.

In Ground POOL SIZE

Gallons

7,000

9,000

12,000

18,000

25,000

30,000

35,000

40,000

* Bypass installation recommended. NR–This pump size is not recommended for this size pool.

3/4 hp 1 hp 1 1/2 hp 2 hp

Test Strips

8 Hour Pump Run Time

PUMP SIZE

3.0 2.5 2.0 2.0

3.5 3.0 2.5 2.0

4.0 3.5 3.0 2.5

NR 4.0 3.5 3.0

NR NR 4.0 3.0

NR NR 5.0 4.0

NR NR 6.0 5.0

NR NR NR 6.0

• For the first week test the

pool water daily for free chlorine to ensure correct dial setting. Continue to test weekly throughout the season.

Hour Pump Run Time

PUMP SIZE PUMP SIZE

3/4 hp 1 hp 1 1/2 hp 2 hp 3/4 hp 1 hp 1 1/2 hp 2 hp

2.5 2.0 3.5 3.0 1.0 3.0 2.5 2.0

3.0 2.5 2.0 3.5 2.0 3.5 3.0 2.5

3.5 3.0 2.5 2.0 2.5 2.0 1.0 3.0

4.5 3.5 3.0 2.5 3.0 2.5 2.0 1.5

NR 4.5 3.5 3.0 3.5 3.0 2.5 2.0

NR 5.0 4.5 3.5 NR 3.5 3.0 2.5

NR 6.0 5.0 4.5 5.0 4.0 3.5 3.0

NR NR 6.0 5.0 6.0 5.0 4.0 3.5

* *

If using another means of chlorine support

Follow steps 1-5 on page 5 then continue below.

Hour Pump Run Time

* *

• After each testing, adjust the dial

up by 1/2 increment if the free chlorine reading has dropped below 0.5 ppm or adjust down by 1/2 increment if the reading has risen above 1.0 ppm. Continue this process each day until the free chlorine reading stabilizes to at least 0.5 ppm.

• Remember to adjust dial ONLY by 1/2 setting per day in

order to prevent over chlorination which may bleach pool surfaces.

• Shock pool every two weeks

or as needed to maintain water quality. Follow label directions on the shock treatment used.

• Leave POOL FROG

Chlorine Cycler empty and set dial on POOL FROG® Mineral Cycler to Maximum.

• Shock pool every two weeks

or as needed to maintain water quality. Follow label directions on the shock treatment used.

Replacing a POOL FROG

Mineral Reservoir

(POOL FROG® Mineral Reservoirs MUST be Replaced Every Season)

• Check the front of the box and back label of product to

INGROUND SERIES 5400 (Order #01-12-5412)

NOW FITS THE FOLLOWING CYCLERS:

POOL FROG Series 5400, 5450 or 5600 Prevail Series 5790

7322906 05401

make sure you have the correct POOL FROG® Mineral Reservoir to fit your POOL FROG® Mineral Cycler.

THE POOL FROG

MINERAL RESERVOIR MUST BE REPLACED EVERY 6 MONTHS OR AFTER ONE POOL SEASON WHICHEVER IS SHORTER

Open the box and remove the POOL FROG® Mineral Reservoir

• IMPORTANT: Remove and read the

information card.

Please note: complete instructions for inserting a POOL FROG Reservoir and FROG BAM® are included inside the POOL FROG

Mineral

Mineral Reservoir box.

• Turn off pump.Turn dial to

Setting 0. This reduces the flow of water into the unit when the cap is open.

• Use the cap tool included

with POOL FROG

XL PRO to loosen cap on POOL FROG® Mineral Cycler by hitting the handle with the flat of your hand counter clockwise.

CAUTION read carefully

• USE ONLY the factory recommended replacement

POOL FROG FROG® Pac. DO NOT USE any other Pac or bulk chemical tablets in the POOL FROG® Cyclers. Use of any other product could result in damage to pool equipment or surface, unsafe pool conditions, fire or explosion. Warranty will be void if the correct POOL FROG BAM® and POOL FROG® Pac are not used.

Mineral Reservoir, FROG BAM® and POOL

Mineral Reservoir, FROG

SLOT IN POOL FROG MINERAL RESERVOIR

FIN INSIDE OF POOL FROG MINERAL CYCLER

• Find slot on side of

POOL FROG

Mineral Reservoir and line up with fin inside the POOL FROG Cycler. Lower POOL FROG Reservoir into POOL

FROG

Mineral

Mineral Cycler

until secure.

Replace FROG BAM® for an Algae Protection Guarantee

If you are not using FROG BAM®, proceed to Step 15. See FROG BAM

product labeling for complete directions

for use (EPA Reg. No. 53735-9).

• Remove cap from

FROG BAM® without removing seal.

90 DAY ALGAE PROTECTION

For a preventive dose add:

•

One FROG BAM

•

Two FROG

BAM®

per 10,000 to 15,000 gallons per 15,000 to 30,000 gallons.

11.

12.

• Turn pump on for 90

minutes allowing FROG BAM® to circulate through pool.

• To remove FROG BAM

turn pump off. Turn dial to Setting 0.

POOL FROG

Mineral Cycler

10.

POOL FROG

Chlorine

Cycler

• Insert upside down

into center of POOL

FROG

Mineral Reservoir pushing down firmly on key inside to puncture seal on FROG BAM® bottle.

• Replace cap by hand only.

DO NOT OVER TIGHTEN.

• Turn control dial on POOL

FROG

Mineral Cycler to

Maximum.

13.

14.

POOL FROG

Mineral Cycler

• Remove POOL FROG

Mineral Cycler cap.

• Lift FROG BAM

up and allow any water in the container to drain through the POOL FROG Mineral Cycler before discarding in trash.

NOTE: If water shows more than a hint of blue inside POOL FROG Mineral Cycler, replace the cap, turn dial to Maximum and run the pump for one minute.

14a. If pool size requires additional FROG BAM®, repeat steps 7-14.

POOL FROG

Chlorine

Cycler

14b. When water is clear in POOL FROG

Cycler, discard FROG® BAM bottle and set dial back to

Mineral

Maximum.

Replacing a POOL FROG Pac

Turn off pump. Turn dial to Setting 0. This reduces the flow of water into the unit when the cap is open.

CAUTION Read Carefully – USE ONLY the factory recommended replacement Pac. (See label.) DO NOT USE any other Pac or bulk chemical tablets in the POOL FROG

Use of any other product could result in over chlorination, bleached liners, unsafe pool conditions, fire or explosion. Warranty will be void if the correct Pac is not used.

Open POOL FROG Chlorine Cycler using cap tool by hitting the handle with the flat of your hand counter clockwise. Stand back upon removing cap to avoid inhaling fumes.

Cutting handle from POOL FROG® Pac using Pac

Cutting Tool or a hacksaw

(KEEP OUT OF REACH

OF CHILDREN).

Indent in plastic

Chlorine Cycler.

Turn POOL FROG

POOL FROG

Pac

towers

POOL FROG Pac towers

over and shake slightly until tablets fall into tower

Pac

areas.

POOL FROG Pac

Insert POOL FROG into POOL FROG Cycler, lining up the openings in the POOL

FROG

Pac with keys in POOL FROG Cycler. NOTE: Openings are a different shape than keys.

Chlorine

Pac

Chlorine

A. Find the indent in the plastic.

C. Squeeze the handles together. Repeat for other side.

Finished cut ends

B. If using a Pac Cutting

Tool, place curved section of tool around the narrow end of one Pac tower and line up blade on indent.

D. If using a hacksaw to cut the Pac, line up hacksaw blade on indent and cut with a smooth sawing action.

Avoid a pinched opening.

A correct oval opening

POOL FROG

Mineral Cycler

POOL FROG

Chlorine

Cycler

Avoid sparks, open flame or smoking while handling the POOL FROG

Replace cap by hand only.

DO NOT OVERTIGHTEN.

DO NOT USE CAP TOOL TO TIGHTEN CAP. FOR REMOVAL ONLY.

Opening in POOL FROG Pac

Key in POOL FROG Chlorine Cycler

Pac.

E. Whether using a Pac Cutting Tool or a hacksaw, make sure the blade comes straight across on the indent line for a clean cut.

F. If openings are pinched together, open with fingers or re-cut closer to the colored screens inside POOL FROG Pac. Leave at least 1/4" of plastic to fit into POOL

FROG

Chlorine Cycler base.

The POOL FROG made of HDPE #2 plastic. When the POOL FROG

Pac is

Pac is empty, triple rinse

in pool water, drain, and recycle or wrap in newspaper and discard in trash.

Troubleshooting

For more in-depth troubleshooting, go to www.kingtechnology.com

Problem Remedy

What do I do

if the water looks cloudy?

What do I do

if the water turns color?

What do I do

if algae forms in or on my pool?

1. Make sure your filtration system is working properly (i.e. clean filter, skimmer and pump basket).

2. Make sure circulation time is adequate – increase pump time if not.

1. Metals in the fill water may have been oxidized. Have the pool tested. Shock the pool and clean the filter until water clarity returns.

1. Use a nonmetallic (polyquat) algaecide per the directions on the bottle and brush the sides of the pool often.

2. Clean the filter and shock the pool with chlorine daily until water clarity returns.

3. Make sure the pool is properly balanced (see page 4).

4. Shock the water to eliminate build up of any organic matter.

2. Algae may be trying to form – shock the pool, increase circulation time if needed and clean the filter.

3. If you are in an area of the country that struggles with algae growth, see your dealer regarding a 90-day Algae Protection Guarantee using FROG BAM

hang tag for guarantee details.

. See product

5. Make sure pool has a free chlorine reading of

0.5 to 1.0 ppm.

6. Check with your dealer for more information.

3. Check with your dealer for more information.

4. Check with your dealer for more information.

What do I do

if I am under chlorinating with the POOL FROG Pac?

What do I do if I am over

chlorinating with the POOL FROG Pac?

1. If you are unable to maintain

0.5 to 1.0 ppm, first make sure there are chlorine tablets in the tower areas of the POOL FROG

Pac and it is installed properly. If a correction was made, test the water in 24 hours.

2. If still low, turn the dial up one setting and test the water again in 24 hours. Continue

1. If the chlorine reading is over

3.0 ppm, remove the Chlorine Pac from the POOL FROG Chlorine Cycler and test the water daily until the reading is down to

1.0 ppm.

2. Reinsert the POOL FROG Pac, lower the dial one setting

raising the setting by one increment each day until the proper reading is achieved.

3. Shock the pool if the reading has been lower than 0.5 ppm for more than one day.

4. Increase pump time if possible.

and test the water again in 24 hours. If the reading has risen, lower the dial one setting again. Continue this process until proper reading is achieved.

3. If over-chlorinating at the

lowest possible setting, consider decreasing the circulation time.

5. Contact your dealer to have your back pressure tested to ensure it is between 3 & 8 psi.

6. Contact King Technology’s Customer Service Department at 800-222-0169.

Depending on your pump size, you may be circulating the water more than is necessary which results in more chlorine than is necessary.

4. Contact King Technology’s Customer Service Department at 800-222-0169.

Parts List

Parts for both POOL FROG® XL PRO Cyclers

REF. # PART NUMBER DESCRIPTION QTY. REQ.

1 & 2 01-22-9414 Cap w/O-ring 1 2 01-22-9920 Cap O-ring 1 3 N/A Body 1 4 01-22-9480 Pressure Relief Valve 1 5, 6, 7 01-22-9441 Control Dial with O-Rings 1 6 & 7 01-22-9450 Control Dial O-ring Kit 1 8 & 9 01-22-9941 Knob with O-ring 2 10 01-22-9490 2" Male Adapter 2 11 01-22-8870 Cap/Control Dial Tool 1 12 01-22-9970 Silicone Lubricant 1 13 01-22-9980 Pac Cutting Tool 1 14 N/A Shroud 1

DETAIL OF

EACH CYCLER

OPY

POOL FROG® Cycler Maintenance

Replacing the Control Dial O-Rings

• Using a needle nose pliers,

find the snap ring tail located at approximately the five o'clock position under the control dial.

• Pull down and out of the

groove.

• Using a large screwdriver,

loosen the control dial. Carefully pry the dial until it pulls out.

Replacing Cap O-Ring

• Hold cap in front of you

upside down with the o-ring groove facing up. Place one end of o-ring into cap groove at the point closest to you. Hold o-ring down with the thumb and forefinger of one hand.

• Take hold of the far end of

the o-ring with the thumb and index finger of the other hand. Roll o-ring slightly back towards you as you stretch the o-ring into the remainder of the cap groove.

C O

• Carefully replace the rubber

o-ring without stretching it.

Apply silicone lubricant, that came with your POOL FROG

• Lubricate o-ring often with

silicone lubricant that came with your POOL FROG

XL PRO. DO NOT USE petroleum based lubricants.

XL PRO, on o-ring.

• Push control dial completely

Replacing knob

into the housing and turn the dial to setting 2.

• Replace knob in back of

both POOL FROG® XL PRO Cyclers by unscrewing old one

• Insert the non-lipped end of

and screwing in new one.

snap ring into the groove opening beginning at the 5 o'clock position and push it up so that it threads itself around the control dial.

• Using a small screwdriver or

pointed tool to help guide it, make sure the snap ring stays in the groove as it is inserted.

Winterizing

• Turn pump off and turn

dial to Setting 0.

POOL

FROG Mineral Reservoir

POOL FROG

Mineral Cycler

POOL FROG Pac

POOL FROG

Chlorine

Cycler

• Remove the POOL

FROG

Mineral Reservoir and discard in trash. Even if you hear spent minerals inside, it is no longer effective.

Remove the POOL FROG® Pac. If it still contains chlorine, wrap in plastic bag and store in shed or garage away from children

and pets.

• Make sure POOL FROG

Pac is away from open flame or anything metal.

• Remove both caps.

• Unscrew knob in the back

of both POOL FROG

XL PRO Cyclers. Allow all water to drain.

• Replace both caps loosely.

TOOLS NEEDED

In-line Installation

Pipe Wrench

Hacksaw

Tape Measure

MATERIALS NEEDED

PVC Cement

PVC

CEMENT

Install unit after all equipment and as far as possible from heater.

Minimum 12" above opening

Minimum 12" to side

Allow a minimum of 12" above and on each side of

POOL FROG

Do NOT install POOL FROG

XL PRO off-line.

Bi-flow valve design allows water flow in either direction.

room for easy replacement of Mineral Reservoir and POOL FROG® Pac.

COPPER PIPE

Do NOT install in copper pipe if using POOL FROG

Pac as

chemical corrosion occurs.

Minimum 12" above opening

Minimum 12" to side

XL PRO to ensure

POOL FROG

RECOMMENDED

Corrosion Resistant Check Valve

#10 X 1 1/4" Phillips Pan Head Screws with Washers

Use Phillips pan head screws through the mounting holes at the POOL FROG bases to secure the POOL FROG

Cycler

XL PRO into a treated wood base.

Measure the distance between outside male adapters and cut out a section of pipe 3” less than that dimension.

Insert PVC pipe into male adapters with a twisting action. Hold in place 5 to 10 seconds to bond.

PVC

CEMENT

Following PVC cement directions brush PVC cement on the inside of the male adapters and to ends of the pipe .

Isolating the POOL FROG corrosion resistant check valve is recommended.

XL PRO by installing a

For Proper Performance

Make sure back pressure Is between

3 and 8 psi

Higher back pressures could result in over chlorination. Lower back pressures could result in under chlorination. Adjust eye ball fittings in the return jets to a larger size to decrease back pressure or smaller size to increase back pressure. Contact your dealer to have your back pressure tested to ensure it is between 3 and 8 psi.

2) Recommended flow rates for in ground unit is 20-80 gpm.

3) Determine possible high-flow situations that require a special installation such as:

A. Water flow is higher than 80 gpm.

B. In-floor cleaner is included with pool.

C. Pool and spa combination with common equipment.

NOTE: Over chlorination or damage to the POOL FROG

XL PRO Cyclers or other equipment could result if these special installations are not used in these situations.

A. With High GPMS Install T-fittings exactly as shown.

CHECK VALV E

SUCTION FROM POOL/SPA

B. With In-floor Cleaners

3-WAY VALVE

PUMP

➜➜

➜

POOL FROG XL PRO

➜

POOL FROG XL PRO

IN-FLOOR

➜

VALVE

➜

POOL WATER LEVEL

TO POOL

C. Pool and Spillover Spa Combination

CHECK VALVE

SUCTION FROM POOL/SPA

PUMP

POOL FROG XL PRO

3-WAY

TO POOL

TO SPA

POOL FROG® XL PRO Two-Year Limited Warranty

King Technology, Inc. warrants to the original purchaser this unit will be free from any defects in workmanship and/or material, for a period of two (2) years from the date of original purchase. This warranty covers body, cap and control dial, but specifically excludes o-rings. King Technology at its option may replace any defective parts or the entire unit without charge after it is determined what is needed to correct any deficiency. Replacement parts with the exception of o-rings are warranted for the remainder of the original warranty. To extend the limited warranty from two years to ten years, simply complete the warranty card that came with your unit and return it to King Technology within 30 days of purchase and installation.

1. To obtain warranty service, you must deliver the unit to King Technology or its nearest authorized dealer. Shipping expenses are the purchaser's responsibility. The name of the nearest authorized dealer can be obtained by writing or calling King Technology at the address and telephone number provided below. Proof of purchase is required when requesting warranty service. Purchaser must present the sales receipt or other documentation verifying proof of purchase.

2. This warranty does not cover defects caused by: Modification, alteration, repair or service of the unit contrary to the accompanying instructions; physical abuse to or misuse of the product or operation or installation in a manner contrary to the accompanying instructions. This warranty also excludes all costs arising from the installation, adjustment, removal or replacement of defective units or parts. This warranty also excludes any and all claims arising out of the chemicals used in the product or their characteristics.

3. CAUTION - Read carefully – Failure to follow these instructions will void the warranty. Do not add shock in or near skimmer.

A. This unit is not designed for shock treatment of pools. See your pool dealer or distributor for further information concerning shock treatments.

B. Control dial settings in excess of the recommended setting levels for trichlor can result in excess sanitizers being discharged

into the pool. This can result in bleaching or discoloration of areas around the pool inlet or in some cases bleaching or discoloration of the entire pool liner or paint.

C. Excess trichlor in the pool can create health hazards to bathers. Consult each chemical manufacturer's warnings and cautions for specifics.

D. Misuse or failure to use the proper POOL FROG

Reservoir and POOL FROG

Pac may cause damage to

Mineral

equipment or personal injury. This warranty will be null and void, if this unit is not used with the recommended POOL FROG Mineral Reservoir and POOL FROG® Pac.

4. This warranty is the exclusive warranty for the POOL FROG

PRO. This warranty is not transferable. KING TECHNOLOGY

MAKES NO REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER MATTER CONCERNING THE POOL FROG

XL PRO. Any express warranty not provided herein, and any remedy for breach of contract but which for this provision might arise by implication or operation of law is hereby excluded and disclaimed. THE EXCLUSIVE REMEDY FOR ANY CUSTOMER IS THE REPAIR OR REPLACEMENT OF THE UNIT, AND THE RECOVERY OF DAMAGES WILL NOT EXCEED THE PURCHASE PRICE OF THE UNIT. IN NO EVENT WILL KING TECHNOLOGY BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL OR PUNITIVE DAMAGES FROM ANY CAUSE.

5. Under no circumstance shall King Technology be liable to purchaser or any other person for any damage or loss incurred because of any chemicals used in the product or their physical characteristics, or interruption of service of the product, or any resulting special, incidental or consequential damages or losses. Some states do not allow the exclusion or limitation of incidental consequential damages, so the above limitation or exclusion may not apply to you.

Covered by one or more of the following U.S. Patent Numbers: 4,662,387; 5,076,315; 5,218,983; 6,190,547; 6,210,566; 6,217,892; 6,383,507; 6,551,609; 6,652,871; 6,544,415 and other U.S. and Foreign Patents Pending.

Manufactured by: KING TECHNOLOGY, INC. 530 11th Avenue South, Hopkins, MN 55343 U.S.A. 952-933-6118 • 800-222-0169 • FAX 952-933-2206 www.kingtechnology.com

Made in U.S.A.

20-48-0220E

553100543R2

King Technology 5450 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

TABLE OF CONTENTS

Swimming Pool Tips

Troubleshooting

Winterizing