Kingston HX318C9SR/8 User Manual
HX318C9SR/8
8GB (8GB 1G x 64-Bit)
DDR3-1866 CL9 240-Pin DIMM
SPECIFICATIONS
DESCRIPTION
HyperX HX318C9SR/8 is a 1G x 64-bit (8GB) DDR3-1866 CL9
SDRAM (Synchronous DRAM) 2Rx8, memory module, based
on sixteen 512M x 8-bit FBGA components per module. Each
module supports Intel® XMP (Extreme Memory Profiles).
Each module has been tested to run at DDR3-1866 at a low
latency timing of 9-10-11 at 1.5V. The SPDs are programmed
to JEDEC standard latency DDR3-1600 timing of
11-11-11 at 1.5V. Each 240-pin DIMM uses gold contact
fingers. The JEDEC standard electrical and mechanical
specifications are as follows:
CL(IDD)
Row Cycle Time (tRCmin)
Refresh to Active/Refresh
Command Time (tRFCmin)
Row Active Time (tRASmin)
Maximum Operating Power
UL Rating
Operating Temperature
Storage Temperature
*Power will vary depending on the SDRAM used.
11 cycles
48.125ns(min.)
260ns(min.)
35ns(min.)
TBD W*
94 V - 0
o
C to +85o C
0
o
C to +100o C
-55
FEATURES
• JEDEC standard 1.5V (1.425V ~ 1.575V) Power Supply
• VDDQ = 1.5V (1.425V ~ 1.575V)
• 800MHz fCK for 1600Mb/sec/pin
• 8 independent internal banks
• Programmable CAS latency: 11, 10, 9, 8, 7, 6
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• 8-bit pre-fetch
XMP TIMING PARAMETERS
•
JEDEC: DDR3-1600 CL11-11-11 @1.5V
• XMP Profile #1: DDR3-1866 CL9-10-11 @1.5V
• XMP Profile #2: DDR3-1600 CL9-9-9 @1.5V
kingston.com/hyperx
• Burst Length: 8 (interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write (either on the fly using A12 or
MRS)
• Bi-directional Differential Data Strobe
• Internal (self) calibration: Internal self calibration through ZQ
pin (RZQ: 240 ohm ± 1%)
• On Die Termination using ODT pin
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°Cº
• Asynchronous Reset
• Height 1.311” (33.30mm), w/heatsink, double sided component
Continued >>
Document No. 4807123-001.B00 04/22/15 Page 1
continued HyperX
MODULE WITH HEAT SPREADER
7.9 mm
133.35 mm
33.3 mm
MODULE DIMENSIONS
FOR MORE INFORMATION, GO TO WWW.KINGSTON.COM/HYPERX
All Kingston products are tested to meet our published specifications. Some motherboards or system configurations may not operate at the
published HyperX memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers faster than
the published speed. Overclocking or modifying your system timing may result in damage to computer components.
kingston.com/hyperx
Document No. 4807123-001.B00 Page 2
Loading...