Kingston DATATRAVELER LOCLER PLUS User Manual
DataTraveler® Locker+ User Manual
Document No. 48008071-001.A02 DataTraveler® Locker+ Page 1 of 22
Table of Contents
About This Manual .................................................................................................................. 3
System Requirements............................................................................................................. 3
Recommendations .................................................................................................................. 3
Setup (Windows Environment)............................................................................................... 4
Device Initialization (Windows Environment) ....................................................................... 5
Device Usage (Windows Environment) ................................................................................. 9
Device Options (Windows Environment)............................................................................. 10
Setup (Mac Environment) ..................................................................................................... 12
Device Initialization (Mac Environment).............................................................................. 13
Device Usage (Mac Environment)........................................................................................ 17
Device Options (Mac Environment) ..................................................................................... 18
Help and Troubleshooting.................................................................................................... 20
Device Lockout.........................................................................................................................20
Forgot Password......................................................................................................................21
Drive Letter Conflict (Windows Operating Systems)............................................................22
Document No. 48008071-001.A02 DataTraveler® Locker+ Page 2 of 22
About This Manual
This user manual covers the DataTraveler® Locker+ (referred to simply as DTL+ from this point
forward) based on the factory image with no implemented customizations.
System Requirements
PC Platform
• Pentium III Processor or equivalent (or
faster)
• 15MB free disk space
• USB 2.0
PC Operating System Support
• Windows
®
7
• Windows® Vista SP1, SP2
• Windows® XP SP2, SP3
• Two consecutive drive letters after the
last physical drive*
Mac Platform
• 15MB free disk space
• USB 2.0
Operating System Support
• Mac OS X 10.5.x
• Mac OS X 10.6.x
Recommendations
To ensure there is ample power provided to the DTL+ device, insert it directly into a USB port
on your notebook or desktop, as seen in
peripheral device(s) that may feature a USB port, such as a keyboard or USB-powered hub, as
seen in
Figure 1.2.
Figure 1.1. Avoid connecting the DTL+ to any
Figure 1.1 – Recommended Usage
Figure 1.2 – Not Recommended
*Note: See ‘Drive Letter Conflict’ on page 22.
Document No. 48008071-001.A02 DataTraveler® Locker+ Page 3 of 22
Setup (Windows Environment)
1. Insert the DTL+ into an available USB port on
your notebook or desktop and wait for Windows
to detect it.
• Windows XP users will receive a ‘Found New
Hardware’ notification as seen in
• Windows Vista/7 users will receive a device
driver notification as seen in
Once the new hardware detection is complete,
Windows will prompt you to begin the initialization
process.
• Windows
XP users can skip step 2 and go to
page 5 – Device Initialization.
• Windows Vista/7 users will see an AutoPlay
window similar to the one in Figure 2.3.
2. Select the option ‘Run DTLplus_Launcher.exe’.
If Windows does not AutoPlay, you can browse to
the CD-ROM partition (Figure 2.4) and manually
execute the DTLplus_Launcher program. This will
also start the initialization process.
Figure 2.1.
Figure 2.2.
Figure 2.1 – Found New Hardware
(Windows XP)
Figure 2.2 – Device Driver Installation
(Windows Vista/7)
Figure 2.3 – AutoPlay Window
(Windows Vista/7)
(Note: Menu options in the AutoPlay
window may vary depending on what
programs are currently installed on
Figure 2.4 – DTL+ Contents
Document No. 48008071-001.A02 DataTraveler® Locker+ Page 4 of 22
your computer. AutoRun will start the
initialization process automatically.
)
Device Initialization (Windows Environment)
1. Select your language preference from the drop-down menu and click ‘Next’ (Figure 3.1.)
Figure 3.1 – Language Selection
2. Review the license agreement and click ‘Next’ (Figure 3.2.) (Note: You must accept the
license agreement before continuing; otherwise the ‘Next’ button will remain disabled.)
Figure 3.2 – License Agreement
Document No. 48008071-001.A02 DataTraveler® Locker+ Page 5 of 22
3. Create a password to protect your data on the DTL+. Enter it in the ‘Password’ field, then
re-enter it in the ‘Password Confirmation’ field, as seen below in
Figure 3.3. The password
you create must meet the following criteria before the initialization process will allow you to
continue:
1. Passwords must contain 6 characters or more (up to 16 characters.)
2. Passwords must contain three (3) of the following criteria options:
- UPPER CASE, lower case, numeric, and/or special characters (!, $, etc.)
You may also enter a password hint, but it is not a mandatory field. The hint field can be
useful in providing a clue as to what the password is, should the password ever be
forgotten. (Note: The hint CANNOT be an exact match to the password.)
Figure 3.3 – Password Setup
Document No. 48008071-001.A02 DataTraveler® Locker+ Page 6 of 22
4. Enter your contact information into the text boxes provided (see Figure 3.4) (Note: The
information you enter in these fields may NOT contain the password string you created in
Step 3. However, these fields are optional and can be left blank, if so desired.)
• The ‘Name’ field may contain up to 32 characters, but cannot contain the
exact password.
• The ‘Company’ field may contain up to 32 characters, but cannot contain
the exact password.
• The ‘Details’ field may contain up to 156 characters, but cannot contain
the exact password.
Figure 3.4 – Contact Information
5. Click ‘Finish’ to complete the device initialization process.
Document No. 48008071-001.A02 DataTraveler® Locker+ Page 7 of 22
Loading...