Kingsman MQRB4436N, MQRB4436LPE, MQRB5143N, MQRB5143NE, MQRB5143LP Installation Instructions Manual

...

Page 1

Infinite Series

Model Numbers:

MQRB4436N, MQRB4436NE, MQRB4436LP, MQRB4436LPE MQRB5143N, MQRB5143NE, MQRB5143LP, MQRB5143LPE MQRB6961N, MQRB6961NE, MQRB6961LP, MQRB6961LPE

Certified to:

ANSI Z21.50-2014 • CSA 2.22-2014 ZERO CLEARANCE VENTED GAS FIREPLACE

Installation Instructions

WARNING: If the information in these instructions is not followed exactly, a fire or

explosion may result causing property damage, personal injury or loss of life.

Warning: Improper installation, adjustment, alteration, service or maintenance can cause

property damage, personal injury or loss of life. Refer to this manual. Installation and service must be performed by a qualified installer, service agency or the gas supplier. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

 Do not try to light any appliance.  Extinguish any open flame.  Do not touch any electrical switch.  Do not use any phone in your building.  Immediately call your gas supplier from a neighbor's phone.  If you cannot reach your gas supplier, call the fire department.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

A Division of R-Co. Inc. 2340 Logan Ave. Winnipeg, Manitoba Canada R2R 2V3 Ph.: (204) 632-1962 Printed in Canada October 20, 2014 Part# 51MQ-MAN14

ZERO CLEARANCE VENTED GAS FIREPLACE

Page 2

Table of Contents

Table of Contents.....................................................................................................................................................................

2-3

Child Safety Screen -MQRB4436 & MQRB5143……………………………………………………………………………………..

Child Safety Screen – MQRB6961……………………………………………………………………………………………………..

Recommendations for Finishing of Clean View Linear Products.............................................................................................

Pre-installation Questions and Answers..................................................................................................................................

Operating Instructions..............................................................................................................................................................

Warnings, Installations and Operations...................................................................................................................................

8-9

Installation Requirements for the Commonwealth of Massachusetts.......................................................................................

Nailing Tab Guide for all Units................................................................................................................................................

MQRB4436: Framing Your Gas Fireplace...............................................................................................................................

MQRB4436 Locating Your Appliance / Fireplace Dimensions.................................................................................................

MQRB4436 - Pre-existing Enclosures vs Framing Enclosure Around Fireplace………………………………………………….

MQRB4436 -See Thru Framing...............................................................................................................................................

14-15

MQRB4436 Single Sided Framing...........................................................................................................................................

16-17

MQRB4436 Combustible Enclosure Heights...........................................................................................................................

MQRB4436 Surround Dimensions / Surround Clearances......................................................................................................

MQRB4436 Facing Material Requirements.............................................................................................................................

MQRB4436 Mantel Clearances / Clearance to Combustibles.................................................................................................

MQRB5143: Framing Your Gas Fireplace...............................................................................................................................

MQRB5143 Locating Your Appliance / Fireplace Dimensions………………………………………………………………………

MQRB5143 - Pre-existing Enclosures vs Framing Enclosure Around Fireplace………………………………………………….

MQRB5143 -See Thru Framing...............................................................................................................................................

25-26

MQRB5143 Single Sided Framing...........................................................................................................................................

27-28

MQRB5143 Combustible Enclosure Heights...........................................................................................................................

MQRB5143 Surround Dimensions / Surround Clearances.....................................................................................................

MQRB5143 Facing Material Requirements..............................................................................................................................

MQRB5143 Mantel Clearances / Clearance to Combustibles.................................................................................................

MQRB6961: Framing Your Gas Fireplace...............................................................................................................................

MQRB6961 Locating Your Appliance / Fireplace Dimensions................................................................................................

MQRB6961 - Pre-existing Enclosures vs Framing Enclosure Around Fireplace………………………………………………….

MQRB6961 -See Thru Framing...............................................................................................................................................

36-37

MQRB6961 Single Sided Framing...........................................................................................................................................

38-39

MQRB6961 Combustible Enclosure Heights...........................................................................................................................

MQRB6961 Surround Dimensions / Surround Clearances.....................................................................................................

MQRB6961 Facing Material Requirements..............................................................................................................................

MQRB6961 Mantel Clearances / Clearance to Combustibles.................................................................................................

MQRB4436BK / MQRB5143BK / MQRB6961BK Back Shield Kit –Single View.....................................................................

44-45

MQRB4436 / MQRB5143SK / MQRB6961SK (See Thru Kit) Installation..............................................................................

MQRB4436 / MQRB5143 / MQRB6961 Liner & False Bottom Installation..............................................................................

47-48

MQRB4436, MQRB5143 & MQRB6961 Finishing Options.....................................................................................................

MQRB4436 / MQRB5143 / MQRB6961 Surround Installation.................................................................................................

Fan Installation MQRB4436 / MQRB5143 / MQRB6961..........................................................................................................

Fan Speed Control Outside of Fireplace..................................................................................................................................

Optional Glass Ember Installation............................................................................................................................................

Optional Driftwood & Rock Installation....................................................................................................................................

MQ46D Driftwood / RBCB1 Cannonballs.................................................................................................................................

Door and Glass Information.....................................................................................................................................................

Door Latch Tool.......................................................................................................................................................................

Valve Access Cover Removal / Removable Lower Face Panel...............................................................................................

Gas Line Installation / Gas Specifications................................................................................................................................

Millivolt System, Lighting, and Burner Control.........................................................................................................................

Troubleshooting the Millivolt Gas Control System...................................................................................................................

Burner System Maintenance....................................................................................................................................................

Gas Conversion for Top Convertible Pilot...............................................................................................................................

820 Nova mV Modulating Conversion Kit.................................................................................................................................

MQRB4436 Burner Section: Gas Conversion.........................................................................................................................

Page 3

MQRB5143 Burner Section: Gas Conversion..........................................................................................................................

MQRB4436 / MQRB5143 Burner Tube Removal / Burner System Removal/Installation Guide..............................................

MQRB4436 / 5143 / 6961 Moving Valve to Other Side of Fireplace........................................................................................

MQRB6961 Burner Section: Gas Conversion..........................................................................................................................

MQRB6961 Burner Tube Removal / Burner System Removal/Installation Guide....................................................................

Remote Receiver Location.......................................................................................................................................................

51-UHS For Infinite Series MQRB4436, MQRB5143, MQRB6961..........................................................................................

IPI Electronic Ignition System..................................................................................................................................................

Remote Control Operation.......................................................................................................................................................

IPI Electronic Ignition Parts List – Standard System……………..............................................................................................

IPI Schematic Drawing #1: Basic Manual Hi / Lo – Manual On / Off.......................................................................................

IPI Schematic Drawing #2: Remote On / Off and Manual Hi / Lo.............................................................................................

EGTM / GTM System -No Batteries.........................................................................................................................................

IPI Schematic Drawing #3: Remote On / Off, Variable Hi / Lo, and Fan..................................................................................

Electronic Ignition Lighting Instructions....................................................................................................................................

LK2 Halogen Lamp Kit.............................................................................................................................................................

LK3 Halogen Lamp Kit.............................................................................................................................................................

Venting.....................................................................................................................................................................................

General Vent Installation Information.......................................................................................................................................

84-85

Horizontal Vent Table..............................................................................................................................................................

Venting Examples...................................................................................................................................................................

Wall Thimble and Roof Support.............................................................................................................................................

Installation of Side Wall Venting..............................................................................................................................................

Z57ST24 / Z57ST36 Horizontal Snorkel Terminations MQRB4436 / MQRB5143..................................................................

Venting Straight Up Through Roof..........................................................................................................................................

90-91

Flue Restrictor Adjustment MQRB4436 & MQRB5143...........................................................................................................

PVH58 POWER VENT SECTION

PVH58 Dimensions..................................................................................................................................................................

PVH58 Installation Overview & Termination Installation.........................................................................................................

PVH58 Venting Clearances....................................................................................................................................................

PVH58 Venting Hard Pipe Or Flex.........................................................................................................................................

96-97

PVH58 Venting Configurations................................................................................................................................................

PVH58 Wall Thimble Installation & Power Vent Mounting......................................................................................................

PVH58 Wiring Harness Connections.......................................................................................................................................

100

PVH58 Millivolt System Connections.......................................................................................................................................

101-102

PVCM Schematic – Millivolt.....................................................................................................................................................

103

PVH58 IPI System Connections..............................................................................................................................................

104

PVH58 Basic IPI System Connections....................................................................................................................................

105

PVH58 All IPI System Connections.........................................................................................................................................

106

PVCM Schematic – IPI............................................................................................................................................................

107-108

PVH58 Air Intake Adjustment..................................................................................................................................................

109

PVH58 Troubleshooting...........................................................................................................................................................

110

PARTS LISTS

PVH58 Parts List.....................................................................................................................................................................

111-112

MQRB4436 -Parts List............................................................................................................................................................

113-114

MQRB5143 -Parts List............................................................................................................................................................

115-116

MQRB6961 -Parts List...........................................................................................................................................................

117-118

Common Parts for MQRB4436, MQRB5143 and MQRB6961...............................................................................................

119-120

Glass Safety / Termination Cap Safety –All Units-…………………………………………………………………………………..

121

Limited Lifetime Warranty........................................................................................................................................................

122

Page 4

Infinite Series CSS Child Safety Screen

⚠ WARNING:

Wait until unit is COMPLETELY

cool before touching glass or

attempting to install or remove

Child Safety Screen.

Contents of Kit: [1] Child Safety Screen [2] Screen Mount Brackets [6] 3/8” x 1/2” Screws Assembly Instructions:

Fasten Screen Mount Brackets to Child Safety Screen with supplied screws.

Notch in Mount

Bracket

Insert top of

Screen into

fireplace

opening and

push bottom in.

Drop Screen

into place.

Mount Brackets

will lock screen

in place.

To remove Safety Screen,

WAIT UNTIL FIREPLACE

IS COMPLETELY COOL.

Push up Screen Frame and

pull bottom away from

fireplace.

Page 5

MQRB69CSS Child Safety Screen

⚠ WARNING:

Wait until unit is COMPLETELY

cool before touching glass or

attempting to install or remove

Child Safety Screen.

Contents of Kit: [1] Child Safety Screen [1] Bottom Angle [2] Screen Mount Brackets [11] 3/8” x 1/2” Screws

Assembly Instructions:

Fasten Screen Mount Brackets to Child Safety Screen with supplied screws.

Notch in Mount

Bracket

Insert top

of Screen

into

fireplace

opening

and push

bottom in.

Drop Screen

into place.

Mount Brackets

will lock screen

in place.

To remove Safety Screen,

WAIT UNTIL FIREPLACE

IS COMPLETELY COOL.

Push up Screen Frame and

pull bottom away from

fireplace.

Bottom Angle on Bottom of Screen.

Page 6

Recommendations for Finishing of Clean View Linear Products

When finishing the wall around the fireplace, it is critical that the wall covering be fastened properly. It is acceptable to pre-drill holes and use self-tapping screws which may be used to fasten a backer for tile, marble, etc. Screws being installed through non-combustible board should be self-tapping type with a maximum length of 2 inches. Wall covering fasteners, such as screws or nails, are not permitted in some locations. Do not drill or install longer screws which may penetrate into the lower cover panel area as this may damage internal components.

 Only non-combustible materials may be used over the face of the appliance.  We recommend that DUROCK (non-combustible material) be tied in to the entire perimeter of the fireplace for durability.

Finishing Recommendations (Obtained from professional construction contractors and finishers):

 Frame unit with metal studs (minimum 20 gauge).  Minimum of 1/2” DUROCK cement board (this non-combustible panel is ULC li sted as a wall shield/floor protector) and

fasten to the entire perimeter framing.

 Use fiberglass (mesh) tape for all joints in area of the fireplace.  Use Yellow joint mud (contains high amounts of glue) – two coats, finishing with one coat of green topping mud, sand

and prep for painting.

 If not using a surround, a metal “L” Trim may be used to finish perimeter of DUROCK.  Refer to the following website for more information on using DUROCK Cement Board: www.cgcinc.com

OTHER NOTES:

-A full single sheet of non-combustible board (no joints) above the unit is recommended if possi ble.

-It is preferred to attach the non-combustible board to framing only and not directly to the unit to allow for expansion and contraction during normal operation.

-Lighter colored painted surfaces may discolor due to heat exposure.

Page 7

Pre-installation Questions and Answers

Operating Instructions

1. Be sure to read and understand all the instructions in this manual before operation of appliance.

2. Ensure all wiring is correct and properly enclosed to prevent possible shock.

3. Check for gas leaks.

4. Make sure the glass door is properly installed before operation. Never operate the appliance with the glass door removed.

5. Make sure venting and termination cap are installed and unobstructed.

6. If brick or porcelain liners are used, ensure they are installed.

7. Verify that the pilot can be seen when lighting the appliance. If not, the log or rock placement is incorrect.

8. If the unit is turned off, you must wait a minimum of 60 seconds before re-lighting it.

About curing of the paint

Your stove or fireplace has been painted with the highest quality silicone stove paint. This paint dries quickly in 15-20 minutes when first applied at the factory. However, due to the high temperature silicone components, the paint will cure when heat is applied to the appliance as it is first used. The following information applies to the curing process to get the paint fully hard and durable.

Fire the appliance four successive times for 10 minutes each firing and a 5 minute cool down between each. Be aware during log and firebox paint curing that a white deposit may be developing on the inside of the glass doors. It is important to remove this white deposit from the glass doors using a fireplace glass cleaner.

 Babies, small children, pregnant women and pets should leave the area during the cure phase.  Ventilate well, open doors and windows.  Do not touch during curing.

Why does my fireplace or stove give off odour?

It is normal for your fireplace to give off some odour. This is due to the curing of the paint, adhesives, silicones and any undetected oil from the manufacturing process as well as the finishing materials used with the installations (e.g. marble, tile and the adhesives used to adhere this product to the walls can react with heat and cause odours).

It is recommended that you burn your gas fireplace or stove for a minimum of four hours at a time with the fan off (if a fan is present) after the curing of the paint has been completed. These odours can last upward to 40 hours of burn time; keep burning at a minimum of four hours per use until odours dissipate.

Noise coming from the fireplace?

Noise is caused by the expansion and contraction of metal as the appliance heats up and cools down. This is normal and is similar to the sounds produced by a furnace or heating duct. This noise does not affect the operation or longevity of your fireplace.

Page 8

Warnings, Installations and Operations

WARNING

FOR SAFE INSTALLATION AND OPERATION OF YOUR GAS FIREPLACE PLEASE NOTE THE FOLLOWING:

1. Do not clean when the glass is hot.

2. Do not use abrasive cleaners.

3. Using a substitute glass will void all product warranties.

4. For safe operation, glass doors must be closed.

5. When purging the gas line, the glass front must be removed.

6. Do not strike or abuse glass. Take care to avoid breakage.

7. Do not alter gas orifice.

8. No substitute materials may be used other than factory supplied components.

9. This appliance gives off high temperatures and should be located out of heavy traffic areas and away from furniture and draperies.

10. Children and adults should be alerted to the hazards of the high surface temperatures of this appliance and should stay away to avoid burns or ignition of clothing.

11. Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. To restrict access to a fireplace or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.

12. Under no circumstances should any solid fuels (wood, paper) be used in this appliance.

13. Under no circumstances should this appliance be modified. Any parts that have to be removed for servicing should be replaced prior to operating this appliance.

14. Any safety screen, guard, or barrier removed for servicing an appliance must be replaced prior to operating the appliance.

15. Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, et cetera. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean. Make sure that the gas valve and pilot light are turned off before you attempt to clean this unit.

16. Clothing or other flammable material should not be placed on or near the appliance. This appliance should not be used as a drying rack for clothing nor should Christmas stockings or decorations be hung from it.

17. Do not use this heater if any part has been under water. Immediately call a qualified service technician to inspect the heater and to replace any part of the control system and any gas control which has been under water.

18. Do not operate appliance unless completely installed as per installation instructions.

19. Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

20. WARNING: Do not operate appliance with the glass front removed, cracked or broken. Replacement of the glass should be done by a licensed or qualified service person.

21. The appliance area must be kept clear and free from combustible materials, gasoline, and other flammable vapors and liquids.

22. The front of the fireplace gives off high temperatures that could ignite combustible material which is kept close to the front of the unit.

23. Ensure that power to the Fireplace is turned off before servicing.

24. Do not operate this Fireplace without the glass front or with a broken glass.

25. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the

owner’s information manual provided with this appliance. For assistance or additional information consult a qualified

installer, service agency, or the gas supplier.

26. Operation of this appliance when not connected to a properly installed and maintained venting system or tampering with the blocked vent shutoff system can result in carbon monoxide (CO) poisoning and possible death.

27. This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.

Installation Regulations

This gas appliance must be installed by a qualified installer in accordance with local building codes, or in the absence of local codes, with the current CAN/CSA-B149.1 or .2 Installation Code (in Canada) or the current National Fuel Gas Code Z223.1- NFPA 54 when installed in the United States.

This appliance, when installed, must be electrically connected and grounded in accordance with local codes, or in the absence of local codes, with the current CSA C22.1 Canadian Electrical Code or with the National Electrical Code; ANSI/NFPA 70 when installed in the United States.

In the U.S.A. Thermostats are not permitted for Vented Gas Fireplaces (ANSI Z21.50b-Decorative).

Page 9

 Gas fired appliances may be used only for supplemental heat and/or decorative purposes and under no circumstances shall they

NOTE: It is recommended that a Carbon Monoxide (CO) Detector be installed in or near bedrooms and on all levels of your home. Place a detector about 15ft [4.5m] outside the room that houses your gas appliance.

Certified for installation in a bedroom or bed/sitting room. In Canada must be installed with listed millivolt thermostat.

In the U.S.A. Thermostats are not permitted for Vented Gas Fireplaces (ANSI Z21.50b-Decorative).

In USA see local codes.

provide a primary heat source.

 This appliance must not be connected to a chimney flue serving a separate solid-fuel burning appliance.

Operations and Maintenance Instructions

For safe installation and operation note the following:

• Venting systems should be periodically examined by a qualified agency.

• The flow of combustion and ventilation air must not be obstructed.

• The Burner/Log Assembly has been engineered and permanently adjusted for proper flame control.

• Periodically remove the logs from the grate assembly and vacuum any loose particles from the grate and burner areas. See Log

Placement page to remove logs. Vacuum burner parts and replace logs.

• Never use your gas fireplace as a cooking device.

• Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify

proper operation after servicing.

Installation Requirements for the Commonwealth of Massachusetts

In the Commonwealth of Massachusetts, the installer or service agent shall be a plumber or gas fitter licensed by the Commonwealth. When installed in the Commonwealth of Massachusetts or where applicable codes; the unit shall be installed with a CO detector per the

requirements listed below.

1. For direct-vent appliances, mechanical-vent heating appliances or domestic hot water equipment, where the bottom of the vent

terminal and the air intake is installed below four feet above grade the following requirements must be satisfied:

A. If there is not one already present, on each floor level where there are bedroom(s), a carbon monoxide detector and alarm

shall be placed in the living area outside the bedroom(s). The carbon monoxide detector shall comply with NFPA 720.

B. A carbon monoxide detector shall be located in the room that houses the appliance or equipment and shall:

 Be powered by the same electrical circuit as the appliance or equipment such that only one service switch services

both the appliance and the carbon monoxide detector;

 Have battery back-up power;  Meet ANSI./UL 2034 Standards and comply with NFPA 720; and  Have been approved and listed by a Nationally Recognized Testing Laboratory as recognized under 527 CMR.

C. A Product-approved vent terminal must be used, and if applicable, a Product-approved air intake must be used.

Installation shall be in strict compliance with the manufacturer’s instructions. A copy of the installation instructions shall remain with the appliance or equipment at the completion of the installation.

D. A metal or plastic identification plate shall be mounted at the exterior of the building, four feet directly above the location of

vent terminal. The plate shall be of sufficient size to be easily read from a distance of eight feet away, and read “Gas Vent Directly Below”.

2. For direct-vent appliances, mechanical-vent heating appliances or domestic hot water equipment where the bottom of the vent

terminal and the air intake is installed above four feet above grade the following requirements must be satisfied:

A. If there is not one already present, on each floor level where there are bedroom(s), a carbon monoxide detector and alarm

shall be placed in the living area outside the bedroom(s). The carbon monoxide detector shall comply with NFPA 720.

B. A carbon monoxide detector shall:

 Be located in the room that houses the appliance or equipment;  Be either hard-wired or battery powered or both; and

 Shall comply with NFPA 720.

A Product-approved vent terminal must be used, and if applicable, a Product-approved air intake must be used. Installation shall be in strict compliance with the manufacturer instructions. A copy of the installation instructions shall remain with the appliance or equipment at the completion of the installation.

For the state of Massachusetts a T-handle gas shut-off valve must be used on a gas appliance. This T-handle gas shut-off valve must be listed and approved by the state of Massachusetts. This is in reference to the state of Massachusetts state code CMR238.

Page 10

MQRB4436 / MQRB5143 / MQRB6961 Nailing Tab Guide

The Nailing Tabs on the MQRB4436, MQRB5143 or MQRB6961 can be used in two ways:

1/2” Drywall Flush with Face of Fireplace –Fireplace and Combustible Wall to be covered with Non-Combustible Materials (e.g. Tile around Fireplace). Note: If using Optional Surround, Maximum Thickness for Non-Combustible Material is 3/4”.

Framing Flush with Face of Fireplace -Fireplace to be covered

with Non-Combustibles (e.g. Concrete Board) for Flat Wall appearance.

Note: If using Optional Surround, Maximum Thickness for NonCombustible Material is 3/4”.

[Qty] 2 Nailing Tabs are located on each corner of the fireplace.

Steel Framing Stud

If Combustible (Wood) Framing Studs are used, they must be

Rotated to allow Min.1”

Clearance from Airbox.

[Steel Stud Framing Shown.]

Steel Framing Stud

If Combustible (Wood) Framing Studs are used, they must be

Rotated to allow Min.1”

Clearance from Airbox.

Steel Framing Stud

If Combustible (Wood) Framing Studs are used, they must be

Rotated to allow Min.1”

Clearance from Airbox.

Steel Framing Stud

If Combustible (Wood) Framing Studs are used, they must be

Rotated to allow Min.1”

Clearance from Airbox.

1” Min Clearance Around All Sides of Airbox

Page 11

MQRB4436: Framing Your Gas Fireplace

This section is intended for qualified installers only. Before beginning, make note of where the gas and electrical accesses are located on the unit. This will streamline the construction process. Furthermore, familiarize yourself with the venting and clearance requirements (see Venting section) for this appliance. Failure to comply with those requir ements can seriously compromise the safety and operation of the fireplace.

Kingsman Flex venting MUST be used on the MQRB4436.

Use of DuraVent- DirectVent Pro or other hard pipe Venting systems is not permitted.

Specifications

1. Cold climate installation recommendation: When installing this fireplace against non i

nsulated exterior wall or chase, it is recommended that the outer walls be insulated to conform to applicable insulation codes. Drywall & vapor barrier must be installed over insulation to prevent contact of insulation and unit.

2. Choose fireplace location and frame in accordance with the fireplace framing dimensions specified. Airbox on flue side must maintain Min. 1” Clearance from Combustible (Wood) Framing (see framing di agrams).

3. Drywall or other combustible material can extend up to the Drywall Stops located on the sides of the unit, and up to the bottom and top.

4. When installing horizontal with a 90 degree bend, maintain a minimum of five inches [5"] above the bend with the Wall Thimble Shield [Z57WTS] in enclosures below seventy-two inches [72”]. See MQRB4436 Combustible Enclosure Heights page.

5. A Hearth is not required for this unit.

Vertical Venting in Cold Climates

In cold climate conditions where temperatures go below -10 degrees Celsius or 14 degrees Fahrenheit, we recommend that the chase be insulated and where the vent pipe enters into the attic space that the pipe be wrapped with an insulated Mylar sleeve. This will increase the temperature of the vent and h elp the a pp liance to vent properly in cold weather conditions. It is also important in vertical vented direct vent appliances that the appliance be operated daily during the winter months as this will help stop the termination from freezing up. We recommend using a thermostat [In the U.S.A. Thermostats are not permitted for Vented Gas Fireplaces (ANSI Z21.50b-Decorative)]. set at room temperature to allow the unit to cycle. For IPI models it may be necessary to set the appliance to Standing Pilot mode to maintain heat in the cavity. The purpose of this procedure is to prevent cold air from penetrating the chimney and then onto the living space. Therefore, when the internal temperature is slightly elevated the fireplace is able to freely exhaust its combustion and hence making it easier to startup.

Certified for installation in a bedroom or bedsitting room. In Canada must be installed

with listed millivolt thermostat [In the U.S.A. Thermostats are not permitted for Vented

Stand-off Locations

Gas Fireplaces (ANSI Z21.50b-Decorative)]. In USA see local codes.

Make note of where the stand-off locations are. These stand-offs are provided as indicators to illustrate the boundaries for framing. Therefore, no framing material is permitted to extend beyond these stand-offs.

Page 12

MQRB4436 Locating Your Appliance

All units are Factory Set for a Left Hand Burner System. Right Hand Burner System Requires Valve to be relocated to right side of unit.

Left Burner System

Right Burner System

All Units Can Be Vented Vertically

Horizontal Run With Min. Vertical Run

MQRB4436 Fireplace Dimensions

Page 13

MQRB4436 - Pre-existing Enclosures vs Framing Enclosure Around Fireplace

Airbox

1” Minimum

Air Space

Inserting Unit Into Pre-existing Enclosure: Enclosure must be 53-1/2” inside width. Opening should be greater than 46-1/2” minimum. Insert airbox on side of unit first and swing into place.

Framing Enclosure Around Fireplace: If unit is in place before enclosure is built, minimum clearances for opening can

be followed.

Page 14

MQRB4436 -See Through Framing

Framing Style shown is for illustration purposes only.

This structure is NOT load bearing.

[Steel Stud Framing Shown]

Airbox must maintain Min. 1” Clearance From Combustible [Wood] Framing.

Wood Framing Stud -Rotated

Wood Framing Stud Rotated for Vent Clearance

1” Min Clearance Around All Sides of Airbox

An MQRB4436SK Kit is required for a See Thru Installation.

Before you begin Framing- Determine for both sides whether the Wall Surface will be flush with the face of the fireplace

(Fireplace and wall to be covered with Non-Combustibles, such as tile), or the Framing will be flush with the face of the fireplace (Flat Wall appearance).

Note: If using Optional Surround, Maximum Thickness for Non-Combustible Material is 3/4”.

(Continued on next page)

Page 15

Wall Surface Flush With Face of Fireplace

Framing Flush With Face of Fireplace

[Steel Stud Framing Shown.]

Steel Framing Stud

Steel Framing Studs

Note: If Combustible (Wood) Framing

Studs are used, they must be Rotated to allow Min.1” Clearance from Airbox.

1” Min Clearance Around All Sides of Airbox

*See “Nailing Tab Guide” and “MQRB4436SK / MQRB5143SK / MQRB6961SK” pages before placing unit into the framed opening.*

Note: If using Optional Surround, Maximum Thickness for Non-Combustible Material is 3/4”.

Page 16

MQRB4436 Single Sided Framing

Framing Style shown is for illustration purposes only.

This structure is NOT load bearing.

[Steel Stud Framing Shown]

* 17” Min. Dimension is for Wall Surface Flush with fireplace. Add 1/2” to this Dimension where a non-combustible wall surface will cover the unit (See Nailing Tab Guide Page also).

Airbox must maintain Min. 1” Clearance From Combustible [Wood] Framing.

Wood Framing Studs Must be Rotated

Wood Framing Stud Rotated for Vent Clearance

FRAMED OPENING 46-1/2” WIDE x 38” TALL

CANTILEVER FINISHED MINIMUM OPENING IS 50-1/2” WIDE

1” Min Clearance Around All Sides of Airbox

An MQRB4436BK Kit is required for a Single Sided Installation.

Before you begin Framing- Determine whether the Wall Surface will be flush with the face of the fireplace (Fireplace

and wall to be covered with Non-Combustibles, such as tile), or the Framing will be flush with the face of the fireplace (Flat Wall appearance).

Note: If using optional surround, maximum thickness for non-combustible material is 3/4”.

(Continued)

Page 17

Wall Surface Flush With Face of Fireplace

Framing Flush With Face of Fireplace

[Steel Stud Framing Shown.]

Steel Framing Stud

Note: If Combustible (Wood) Framing

Studs are used, they must be Rotated to allow Min.1” Clearance from Airbox.

1” Min Clearance Around All Sides of Airbox

Note: If using Optional Surround, Maximum Thickness for Non-Combustible Material is 3/4”.

See “Nailing Tab Guide” and “MQRB4436BK / MQRB5143BK / MQRB6961BK” pages before placing unit into the framed opening.

Page 18

MQRB4436 Combustible Enclosure Heights

[

Cold Climate Recommendation

When installing this fireplace against an exterior wall or chase, it is recommended that the outer walls be insulated to conform to applicable insulation codes. Drywall must be installed over va por barrier and insulation material to prevent direct contact with the appliance.

See Thru or Single Sided Installation

Steel Stud Framing Shown]

Single Side Installation Only

[Steel Stud Framing Shown.]

For Propane Horizontal installations the venting must be a minimum of two

feet vertical off the flue before going horizontal.

The minimum

vertical

installation height

must be adhered

to.

Flex pipe venting

must be fully

stretched.

7-3/4” Min for Natural Gas 24” Min for Propane

37-1/2” Min for Natural Gas 53-3/4” Min for Propane

Kingsman Flex venting MUST on the MQRB4436.

Use of DuraVentDirectVent Pro or other hard pipe

be used

Venting systems is not permitted.

7-3/4” Min for Natural Gas 24” Min for Pro

37-1/2” Min for Natural Gas 53-3/4” Min for Pro

ane

The Wall Thimble Shield Z57WTS is required in

ll Enclosures below 72” [Seventy-Two Inches].

Place Wall Thimble Shield Z57WTS against the Wall Thimble Immediately above the Vent. Install the Wall Thimble Shield using [3] DT Screws.

Page 19

Surround Dimensions MQRB4436

• The Surround Frames are 1” thick, with a 3/4” space behind the frame.

• When using Surrounds, Maximum Thickness for Non-Combustible Facing Materials is 3/4”.

• The Fireplace may be covered up to within 1/2” of the Fireplace Opening with non-combustible materials.

Surround Clearances MQRB4436

Page 20

MQRB4436 Facing Material Requirements

These specifications are the same for all Models (4436N, 4436NE, 4436LP, 4436LPE).

Note: If using Optional Surround, See Surround Clearances Section.

[Steel Stud Framing Shown.]

Note: Do not drive excessively long screws into the face of the unit as internal parts may be damaged.

Steel Stud Framing Shown.

Page 21

Clearance to Combustibles MQRB4436

Front

24” [61cm]

Back Shield Kit to Wall

0” [0cm]

Side (from Stand-offs)

0” [0cm]

Floor*

0” [0cm]

Airbox on Flue Side of Unit

1” [25cm]

Minimum Ceiling Height (from bottom of fireplace)

60” [153cm]

Top (from Stand-offs)

0” [0cm]

Top of 90° Bend under 72” Enclosure

5” (With Wall Thimble Shield [Z57WTS]) All Vent Systems

Top of 90° Bend over 72” Enclosure

4” All Vent Systems

Top of Horizontal Pipe

2” All Vent Systems

Side & Bottom of Horizontal Pipe

1” All Vent Systems

Vertical Vent Pipe

1” All Vent Systems

Kingsman Flex venting MUST be used on the MQRB4436. Use of DuraVent- DirectVent Pro or other hard pipe Venting systems is not permitted.

Mantel Dimensions are from front face or NonCombustible Facing Materials covering fireplace.

[Steel Stud Framing Shown.]

*Note: If appliance is installed directly on carpeting or other combustible material other than wood flooring, a metal or wood panel extending the full width and depth of the appliance must be used. Carpet may extend 1 inch above the floor of the appliance.

-Combustible Objects on Non-

Combustible Mantel Warning-

Combustible objects must not be placed on a Non-combustible Mantel unless the

mantel meets the dimensional requirements for a Combustible Mantel. Refer below to determine whether your mantel conforms to the requirements of

a Combustible Mantel.

Steel Framing Stud

MQRB4436 Mantel Clearances

Before installing any mantels it is important to determine the combustibility of its material(s). There are two types of mantels to consider: Combustible and NonCombustible.

A Combustible Mantel is one that consists of material(s) that may discolor, combust, or lose its integrity in the presence of heat. These types of mantels must strictly conform to the dimensional requirements shown below.

Conversely, a Non-Combustible Mantel is one that is constructed with material(s) that will not combust. Check your local codes and regulations to determine whether your mantel is Combustible or Non-Combustible.

The advantage to Non-Combustible Mantels is that it may extend right up to the tile lip of the fireplace. Combustible mantels must adhere to the dimensional restrictions shown below.

Page 22

MQRB5143: Framing Your Gas Fireplace

Specifications

1. Cold climate installation recommendation: When installing this fireplace against non insulated e xterior wall or chase, it is recommended that the outer walls be insulated to conform to applicable insulation codes. Drywall & vapor barrier must be installed over insulation to prevent contact of insulation and unit.

3. Drywall or other combustible material can extend up to the Drywall Stops located on the sides of the unit, and up to the bottom and top.

5. A Hearth is not required for this unit.

Vertical Venting in Cold Climates

Certified for installation in a bedroom or bedsitting room. In Canada must be installed

with listed millivolt thermostat [In the U.S.A. Thermostats are not permitted for Vented

Stand-off Locations

Gas Fireplaces (ANSI Z21.50b-Decorative)]. In USA see local codes.

Page 23

MQRB5143 Locating Your Appliance

All units are Factory Set for a Left Hand Burner System. Right Hand Burner System Requires Valve to be relocated to right side of unit.

Left Burner System

Right Burner System

All units can be vented vertically

Horizontal Run with Min. Vertical Run

Left Burner System

Right Burner System

MQRB5143 Fireplace Dimensions

Page 24

MQRB5143 - Pre-existing Enclosures vs Framing Enclosure Around Fireplace

Airbox

1” Minimum

Air Space

Inserting Unit Into Pre-existing Enclosure: Enclosure must be 60-1/2” inside width. Opening should be greater than 53-1/2” minimum. Insert airbox on side of unit first and swing into place.

Framing Enclosure Around Fireplace: If unit is in place before enclosure is built, minimum clearances for opening can

be followed.

Page 25

MQRB5143 -See Through Framing

*15-3/8” Dimension is for Wall Surface Flush with Unit on Both Sides.

Add 1/2” to this Dimension for each side where a non-combustible wall surface will cover the unit (See Nailing Tab Guide Page Also).

15-3/8”*

Framing Style shown is for illustration purposes only.

This structure is NOT load bearing.

[Steel Stud Framing Shown]

Airbox must maintain Min. 1” Clearance From Combustible [Wood] Framing.

Wood Framing Stud -Rotated

Wood Framing Stud Rotated for Vent Clearance

1” Min Clearance Around All Sides of Airbox

An MQRB5143SK Kit is required for a See Thru Installation.

Before you begin Framing- Determine for both sides whether the Wall Surface will be flush with the face of the fireplace

(Fireplace and wall to be covered with Non-Combustibles, such as tile), or the Framing will be flush with the face of the fireplace (Flat Wall appearance).

Note: If using Optional Surround, Maximum Thickness for Non-Combustible Material is 3/4”.

(Continued)

Page 26

Wall Surface Flush With Face of Fireplace

Framing Flush With Face of Fireplace

[Steel Stud Framing Shown.]

Steel Framing Stud

Steel Framing Studs

Note: If Combustible (Wood) Framing

Studs are used, they must be Rotated to allow Min.1” Clearance from Airbox.

1” Min Clearance Around All Sides of Airbox

*See “Nailing Tab Guide” and “MQRB4436SK / MQRB5143SK / MQRB6961SK” pages before placing unit into the framed opening.*

Note: If using Optional Surround, Maximum Thickness for Non-Combustible Material is 3/4”.

Page 27

MQRB5143 Single Sided Framing

Framing Style shown is for illustration purposes only.

This structure is NOT load bearing.

[Steel Stud Framing Shown]

17” Min. *

* 17” Min. Dimension is for Wall Surface Flush with fireplace.

Add 1/2” to this Dimension where a non-combustible wall surface will cover the unit (See Nailing Tab Guide Page also).

Airbox must maintain Min. 1” Clearance From Combustible [Wood] Framing.

Wood Framing Studs Must be Rotated

Wood Framing Stud Rotated for Vent Clearance

FRAMED OPENING 53-1/2” WIDE x 38” TALL

CANTILEVER FINISHED MINIMUM OPENING IS 57-1/2” WIDE

1” Min Clearance Around All Sides of Airbox

An MQRB5143BK Kit is required for a Single Sided Installation.

Before you begin Framing- Determine whether the Wall Surface will be flush with the face of the fireplace (Fireplace

and wall to be covered with Non-Combustibles, such as tile), or the Framing will be flush with the face of the fireplace (Flat Wall appearance).

Note: If using optional surround, maximum thickness for non-combustible material is 3/4”.

(Continued)

Page 28

Wall Surface Flush With Face of Fireplace

Framing Flush With Face of Fireplace

[Steel Stud Framing Shown.]

Steel Framing Stud

Note: If Combustible (Wood) Framing

Studs are used, they must be Rotated to allow Min.1” Clearance from Airbox.

1” Min Clearance Around All Sides of Airbox

Note: If using Optional Surround, Maximum Thickness for Non-Combustible Material is 3/4”.

See “Nailing Tab Guide” and “MQRB4436BK / MQRB5143BK / MQRB6961BK” pages before placing unit into the framed opening.

Page 29

MQRB5143 Combustible Enclosure Heights

[

Cold Climate Recommendation

See Thru or Single Sided Installation

Steel Stud Framing Shown]

Single Side Installation Only

For Propane Horizontal installations the venting must be a minimum of two

[Steel Stud Framing Shown]

feet vertical off the flue before going horizontal.

21-5/8” Min for Natural Gas 24” Min for Pro

51-1/2” Min Natural Gas 53-7/8” Min for Pro

ane

Flex pipe venting

ane

The minimum

vertical

installation

height must be

adhered to.

must be fully

stretched.

21-5/8” Min for Natural Gas 24” Min for Propane

51-1/2” Min Natural Gas 53-7/8” Min for Pro

ane

The Wall Thimble Shield Z57WTS is required in All Enclosures below 72” [Seventy-Two Inches].

Place Wall Thimble Shield Z57WTS against the Wall Thimble Immediately above the Vent. Install the Wall Thimble Shield using [3] DT Screws.

Page 30

Surround Dimensions MQRB5143

• The Surround Frames are 1” thick, with a 3/4” space behind the frame.

• When using Surrounds, Maximum Thickness for Non-Combustible Facing Materials is 3/4”.

• The Fireplace may be covered up to within 1/2” of the Fireplace Opening with non-combustible materials.

Surround Clearances MQRB5143

Page 31

MQRB5143 Facing Material Requirements

These specifications are the same for all Models (5143N, 5143NE, 5143LP, 5143LPE).

Note: If using Optional Surround

[Steel Stud Framing Shown.]

, See Surround Clearances Section.

Note: Do not drive excessively long screws into the face of the unit as internal parts may be damaged.

Steel Stud Framing Shown.

Page 32

MQRB5143 Mantel Clearances

Clearance to Combustibles MQRB5143

Front

24”[61cm]

Back Shield Kit to Wall

0” [0cm]

Side (from Stand-offs)

0” [0cm]

Floor*

0” [0cm]

Airbox on Flue Side of Unit

1” [25cm]

Minimum Ceiling Height (from bottom of fireplace)

60”[153cm]

Top (from Stand-offs)

0” [0cm]

Top of 90° Bend under 72” Enclosure

5” (With Wall Thimble Shield [Z57WTS]) All Vent Systems

Top of 90° Bend over 72” Enclosure

4” All Vent Systems

Top of Horizontal Pipe

2” All Vent Systems

Side & Bottom of Horizontal Pipe

1” All Vent Systems

Vertical Vent Pipe

1” All Vent Systems

Vertical Vent Pipe

1” DuraVent-DirectVent Pro /

AmeriVent / Selkirk Direct Temp Systems

Mantel Dimensions are from front face or NonCombustible Facing Materials covering fireplace.

[Steel Stud Framing Shown.]

-Combustible Objects on Non-

Combustible Mantel Warning-

Combustible objects must not be placed on a Non-combustible Mantel unless the

mantel meets the dimensional requirements for a Combustible Mantel. Refer below to determine whether your mantel conforms to the requirements of

a Combustible Mantel.

Steel Framing Stud

Before installing any mantels it is important to determine the combustibility of its material(s). There are two types of mantels to consider: Combustible and NonCombustible.

The advantage to Non-Combustible Mantels is that it may extend right up to the tile lip of the fireplace. Combustible mantels must adhere to the dimensional restrictions shown below.

Page 33

MQRB6961: Framing Your Gas Fireplace

Specifications

1. Cold climate installation recommendation: When installing this fireplace a gai ns t non i nsulated ext erior wall or chase, it is recommended that the outer walls be insulated to conform to applicable insulation codes. Drywall & vapor barrier must be installed over insulation to prevent contact of insulation and unit.

2. Choose fireplace location and frame in accordance with the fireplace framing dim ensions specifi ed. Airbox on flue side must maintain Min. 1” Clearance from Combustible (Wood) Framing (see framing di agrams).

3. Drywall or other combustible material can extend up to the Drywall Stops located on the sides of the uni t, and up to the bottom and top.

4. When installing horizontal with a 90 degree bend maintain a minimum of six and one half inches [6-1/2”] for MQRB6961 above the bend with the Wall Thimble Shield [Z57WTS] in enclosures below seventy-eight inches [78”]. See MQRB6961 Combustible Enclosure Heights page.

5. A Hearth is not required for this unit.

Vertical Venting in Cold Climates

Certified for installation in a bedroom or bedsitting room. In Canada must be installed with listed

millivolt thermostat

Fireplaces (ANSI Z21.50b-Decorative)]. In USA see local codes.

Stand-off Locations

[In the U.S.A. Thermostats are not permitted for Vented Gas

Page 34

MQRB6961 Locating Your Appliance

All units are Factory Set for a Left Hand Burner System. Right Hand Burner System Requires Valve to be relocated to right side of unit.

MQRB6961 Fireplace Dimensions

Page 35

MQRB6961 - Pre-existing Enclosures vs Framing Enclosure Around Fireplace

Airbox

1” Minimum

Air Space

Inserting Unit Into Pre-existing Enclosure: Enclosure must be 78-1/2” inside width. Opening should be greater than 71-1/2” minimum. Insert airbox on side of unit first and swing into place.

Framing Enclosure Around Fireplace: If unit is in place before enclosure is built, minimum clearances for opening can

be followed.

Page 36

MQRB6961 See Thru Framing

Framed Opening 71-1/2” x 45-1/2”

Framing style shown is for illustration purposes only.

This structure is NOT load bearing.

[Steel Stud Framing Shown]

Fireplace vent MUST maintain min. 1” clearance from combustible (Wood) framing. However, if steel stud framing is used, 1” vent clearance is not required.

Also refer to these sections:

Clearance to Combustibles

Enclosure Heights

Venting

Note: If Combustible (Wood) Framing Studs are used, they must be rotated to allow

Min.1” Clearance from Airbox.

1” Min Clearance Around All Sides of Airbox

MQRB6961SK Kit is required for a See Thru Installation.

Before you begin Framing- Determine whether the Wall Surface will be flush with the face of the fireplace (Fireplace

and wall to be covered with Non-Combustibles, such as tile), or the Framing will be flush with the face of the fireplace (Flat Wall appearance).

Note: If using optional surround, maximum thickness for non-combustible material is 3/4”.

(Continued)

Page 37

Wall Surface Flush With Face of Fireplace

Framing Flush With Face of Fireplace

[Steel Stud Framing Shown.]

19-3/8”

20-3/8”

Steel Framing Stud

Steel Framing Studs

Note: If Combustible (Wood) Framing

Studs are used, they must be rotated to

allow Min.1” Clearance from Airbox.

1” Min Clearance Around All Sides of Airbox

Note: If using Optional Surround, Maximum Thickness for Non-Combustible Material is 3/4”.

See the “Nailing Tab Guide” and “MQRB5143SK / MQRB6961SK” pages before placing unit into the framed opening.

Page 38

MQRB6961 Single Sided Framing

*21” Min. Dimension is for Wall Surface Flush with fireplace.

Add 1/2” to this Dimension where a non-combustible wall surface will cover the unit (See Nailing Tab Guide Page also).

21” Min.*

FRAMED OPENING 71-1/2” X 45-1/2”

CANTILEVER FINISHED MINIMUM OPENING IS 77-1/2” WIDE

Framing Style shown is for illustration purposes only.

This structure is NOT load bearing.

Steel Stud Framing Shown

Fireplace vent MUST maintain min. 1” clearance from combustible (Wood) framing. However, if steel stud framing is used, 1” vent clearance is not required.

Also refer to these sections:

Clearance to Combustibles

Enclosure Heights

Venting

Note: If Combustible (Wood) Framing Studs are used, they must be Rotated to

allow Min.1” Clearance from Airbox.

1” Min Clearance Around All Sides of Airbox

An MQRB6961BK Kit is required for a Single Sided Installation.

Before you begin Framing- Determine whether the Wall Surface will be flush with the face of the fireplace (Fireplace

and wall to be covered with Non-Combustibles, such as tile), or the Framing will be flush with the face of the fireplace (Flat Wall appearance).

Note: If using optional surround, maximum thickness for non-combustible material is 3/4”.

(Continued)

Page 39

Wall Surface Flush With Face of Fireplace

Framing Flush With Face of Fireplace

[Steel Stud Framing Shown.]

Steel Framing Stud

Note: If Combustible (Wood) Framing

Studs are used, they must be Rotated to

allow Min.1” Clearance from Airbox.

1” Min Clearance Around All Sides of Airbox

Note: If using Optional Surround, Maximum Thickness for Non-Combustible Material is 3/4”.

*See the “Nailing Tab Guide” and “MQRB5143BK / MQRB6961BK” pages before placing unit into the framed opening.*

Page 40

MQRB6961 Combustible Enclosure Heights

Cold Climate Recommendation

See Thru or Single Sided Installation

[Steel Stud Framing Shown.]

The minimum vertical installation height must be adhered to.

Flex pipe venting must be fully stretched.

26-5/8” Min for Natural Gas or Propane

56-1/2” Min for Natural

Gas or Pro

ane

Single Side Installation Only

[Steel Stud Framing Shown.]

26-5/8” Min for Natural Gas or Propane

56-1/2” Min for Natural

Gas or Pro

ane

MQRB6961:

The Wall Thimble Shield Z57WTS is required in All Enclosures below 78” [Seventy-Eight Inches].

Place Wall Thimble Shield Z57WTS against the Wall Thimble Immediately above the Vent. Install the Wall Thimble Shield using [3] DT Screws.

Page 41

Surround Dimensions MQRB6961

• The Surround Frames are 1” thick, with a 3/4” space behind the frame.

• When using Surrounds, Maximum Thickness for Non-Combustible Facing Materials is 3/4”.

• The Fireplace may be covered up to within 1/2” of the Fireplace Opening with non-combustible materials.

Surround Clearances MQRB6961

Page 42

MQRB6961 Facing Material Requirements

These specifications are the same for all Models (6961N, 6961NE, 6961LP, 6961LPE).

Note: If using Optional Surround

[Steel Stud Framing Shown.]

, MQRB6961 See Surround Clearances Section.

Note: Do not drive excessively long screws into the face of the unit as internal parts may be damaged.

Steel Stud Framing Shown.

Page 43

MQRB6961 Mantel Clearances

Clearance to Combustibles MQRB6961

Front

24”[61cm]

Back Shield Kit to Wall

0” [0cm]

Side (from Stand-offs)

0” [0cm]

Floor*

0” [0cm]

Airbox on Flue Side of Unit

1” [25cm]

Minimum Ceiling Height (from bottom of fireplace)

64” [Vertical Venting] 68”[Horizontal Venting-See MQRB6961 Combustible Enclosure Heights page]

Top (from Stand-offs)

0” [0cm]

Top of 90° Bend under 78” Enclosure

6-1/2” (With Wall Thimble Shield [Z57WTS]) All Vent Systems

Top of 90° Bend over 78” Enclosure

6-1/2” All Vent Systems

Top of Horizontal Pipe

2” All Vent Systems

Side & Bottom of Horizontal Pipe

1” All Vent Systems

Vertical Vent Pipe

1” All Vent Systems

Vertical Vent Pipe

1” DuraVent-DirectVent Pro /

AmeriVent / Selkirk Direct Temp Systems

Mantel Dimensions are from front face or Non-Combustible Facing Materials covering fireplace.

[Steel Stud Framing Shown.]

-Combustible Objects on Non-

Combustible Mantel Warning-

Combustible objects must not be placed on a Non-combustible Mantel unless the

mantel meets the dimensional requirements for a Combustible Mantel. Refer below to determine whether your mantel conforms to the requirements of

a Combustible Mantel.

Steel Framing Stud

Before installing any mantels it is important to determine the combustibility of its material(s). There are two types of mantels to consider: Combustible and NonCombustible.

The advantage to Non-Combustible Mantels is that it may extend right up to the tile lip of the fireplace. Combustible mantels must adhere to the dimensional restrictions shown below.

Page 44

MQRB44BK / MQRB51BK / MQRB69BK Back Shield Kit –Single View

*This Kit must be opened before unit is installed into Framing (See “Single Sided Framing” pages of this Manual).

Contents of Kit:

 Firebox Cover  Heat Shield Assembly  Back Liner  False Bottom c/w Pilot Shield &

False Bottom Cover

 90ml Tube Millpac  (Qty)45- DT Screws

Heat Shield & Firebox Cover

Before placing fireplace into framed opening, you must install the Firebox Cover and the Heat Shield Assembly onto the back of the unit. The remaining parts of this kit can be installed after the fireplace is installed into the framed opening.

Do Not Overtighten or Strip Screws!

Apply a small bead of Millpac to Firebox Cover Gasket before Installation.

Warning: Failure to position the parts in accordance with these diagrams or failure to use only parts

specifically approved with this appliance may result in propert y damage or personal injury.

(Continued…)

Page 45

Back Liner, False

Bottom, and End Panel Installation:

1. Remove Liner Clips from the inside of the Firebox (Fig.1).

2. Place the Back Liner onto the firebox bottom with bends facing the rear firebox cover. Lift into place and set down on firebox ledge (See Fig.2).

3. Next install the False Bottom with larger Dimension to Front Glass Opening (Fig.1), and secure it using DT screws into the mounting tabs on the Burner Tube. Insert Pilot Shield and False Bottom Cover into False Bottom.

4. Place End Panels on top of the False Bottom and tilt into place at either end of the Firebox. Replace the Liner Clips (Fig.1).

5. Place the bottom of the door into the door retainer slot, and then secure the door with the top latches (See Door and Glass page in manual if more information is required).

6. To locate Valve Access Cover, engage the tabs into the slots in the Access Panel Brackets on the Fireplace.

Fig.1

Smaller Dimension

goes Behind Burner Tube

MQRB4436 / MQRB5143 Dimensions

Back Liner

Fig.2

Notched Side on Bottom

MQRB6961 Dimensions

2) Lift into place and Set on Firebox Ledge

Note: Warping and Discoloration of Porcelain or Painted Metal Liners Is Not Covered Under Warranty.

Both Porcelain and Painted Metal Liners may discolor and warp during normal operation of your appliance. This is normal, and not considered a defect.

Fig.3

1) Tilt into Firebox

3) Place onto Firebox Bottom behind Burner

Pilot

Page 46

MQRB44SK / MQRB51SK / MQRB69SK (See Thru Kit) Installation

This basic Kit is required for See Thru installations. Note: To cover the Side Fillers with non-combustible materials, they must be installed before Facing materials are applied.

Components:

[2ea.] Side Fillers Valve Access Cover Glass Door c/w Glass See Thru False Bottom c/w Pilot Shield [4ea.] #6 Black Screws [8ea.] ¼” DT Screws

Installation Procedure:

1. Side Fillers

Place Side Filler onto Side of Fireplace opening. Attach with [2] #6 Screws provided. Repeat for the other side.

Warning: Failure to position the parts in accordance with these diagrams or failure to use only parts

specifically approved with this appliance may result in propert y damage or personal injury.

13-1/8” for MQRB6961

2. False Bottom

Insert False Bottom into Fireplace. Fasten the False Bottom to the Burner Assembly using the DT Screws provided. Insert Pilot Shield into False Bottom.

3. End Panels

Remove the Liner Retainer Clips in the Firebox Top. Place End Panels into Firebox on top of the False Bottom and tilt into place at either end of the Firebox. Replace the Liner Retainer Clips.

4. Door

Place the bottom of the door into the door retainer slot, and then secure the door with the top latches (See Door and Glass Information in manual if more information is required).

5. Valve Access Cover

To locate Valve Access Cover, engage the tabs into the slots in the Access Panel Brackets on the Fireplace.

13-1/8” for MQRB6961

Note: Warping and Discoloration of Porcelain or Painted Metal Liners Is Not Covered Under Warranty. Both Porcelain and

Painted Metal Liners may discolor and warp during normal operation of your appliance. T his is normal, a nd not considered a defect.

Page 47

MQRB4436 / MQRB5143 / MQRB6961 Liner & False Bottom Installation

Single Sided:

MQRB44PB1, MQRB51PB1, or MQRB69PB1-[1ea.] Porcelain False Bottom

MQRB4436PLB, MQRB5143PLB, or MQRB6961PLB-[1ea.] Porcelain Back Liner Panel

MQRB4436 (uses 5143PLE), MQRB5143PLE, or MQRB6961PLE-[2ea.] Porcelain End Panels

Warning: Failure to position the parts in accordance with these diagrams or failure to use only parts

specifically approved with this appliance may result in property damage or personal injury.

Back Liner, End Panel, and False Bottom Installation:

1. Remove Liner Clips from the inside of the Firebox (Fig.1).

2. Place the Back Liner onto the firebox bottom with bends facing the rear firebox cover. Lift into place and set down on firebox ledge (See Fig.2).

4. Place End Panels on

top of the False Bottom and tilt into place at either end of the Firebox. Replace the Liner Clips (Fig.1).

Fig.1

MQRB4436/ MQRB5143

Dimensions

Fig.2

Smaller

Dimension goes

Behind

Burner Tube

MQRB6961 Dimensions

Note: Warping and Discoloration of Porcelain or Painted Metal Liners Is Not Covered Under Warranty.

Both Porcelain and Painted Metal Liners may discolor and warp during normal operation of your appliance. This is normal, and not considered a defect.

Back Liner

Notched Side on Bottom

1) Tilt into Firebox

2) Lift into place and

3) Place onto Firebox

(See Thru Instructions on Other Side)

Page 48

MQRB4436 / MQRB5143 / MQRB6961 Liner & False Bottom Installation

)

See Thru:

False Bottom & End Panel Installation:

1. False Bottom

Insert False Bottom into Fireplace. Fasten the False Bottom to the Burner Assembly with [6] DT Screws provided. Insert Pilot Shield into False Bottom.

2. End Panels

Remove the Liner Retainer Clips in the Firebox Top. Place End Panels on top of the False Bottom and tilt into place at either end of the Firebox. Replace the Liner Retainer Clips.

MQRB44PB2, MQRB51PB2, orMQRB69PB2-[1ea.] Porcelain False Bottom

MQRB4436 (Uses 5143PLE

MQRB5143PLE or MQRB6961PLE-[2ea.] Porcelain End Panels

13-1/8” for MQRB6961

Note: Warping and Discoloration of Porcelain or Painted Metal Liners Is Not Covered Under Warranty.

Both Porcelain and Painted Metal Liners may discolor and warp during normal operation of your appliance. This is normal,

and not considered a defect.

Warning: Failure to position the parts in accordance with these diagrams or failure to use only parts

specifically approved with this appliance may result in property damage or personal injury.

Page 49

MQRB4436, MQRB5143 & MQRB6961 Finishing Options

Using Side Fillers

The Side Fillers are located at each side of the door. They are provided to give a continuous surface up to the opening of the fireplace door.

Using Other Non-Combustible Materials as Side Fillers (Brick, Tile, Marble, etc.)

Non-Combustible facing materials, such as brick or tile may be used in place of the Side Fillers- so long as

the total amount of

material applied is not thicker than 1-1/2” on the inside of the fireplace opening. This will allow for removal of the Glass Door & Access Panel.

Using the Optional Surrounds

The Surround Frames are 1-1/2” & 4” wide and 1” thick, with a 3/4” space behind the frame.

The Fireplace may be covered up to within 1/2” of the opening with noncombustible materials up to 3/4” thick.

The Surround Side Fillers taper in toward the door opening. The Surround Access Panel is tapered to match the angle of the Side Fillers.

Page 50

MQRB4436 / MQRB5143 / MQRB6961 Surround Installation

Surround Kits are available in 3 different finishes:

MQRB4436 MQRB5143 MQRB6961

Small [1-1/2”] Large [4”] Small [1-1/2”] Large [4”] Small [1-1/2”] Large [4”]

MQRB4419SBL MQRB4419SSS MQRB4419SPW

MQRB4424SBL MQRB4424SSS MQRB4424SPW

Each kit contains:

(Qty-1) Surround Frame

(Qty-2) Surround Side Fillers

(Qty-1) Surround Access Cover

(Qty-8) #6 Self Tapping Screws

MQRB5019SBL MQRB5019SSS MQRB5019SPW

MQRB5624SBL MQRB5624SSS MQRB5624SPW

MQRB6919SBL MQRB6919SSS MQRB6919SPW

MQRB6924SBL MQRB6924SSS MQRB6924SPW

-Black

-Stainless Steel

-Pewter

The Surround Frames are 1” thick, with a ¾” space behind the frame. The Fireplace may be covered up to within ½” of the opening with non-combustible materials.

Surround Installation:

1. Note: Original Side Fillers & Valve

Access Cover will not be used.

2. The Lower Front Face Panel must be installed on the fireplace before surround can be installed.

3. Remove Glass Door from fireplace.

4. Hook lower ledge of Surround Frame onto the Lower Front Face Panel of the fireplace. With top of Frame tilted outward, slide Side Fillers behind Surround Frame.

5. Push Surround Frame into place and install using the existing screw holes in the tile lip. Front Edge of the Side Filler must rest between Surround Frame and Fireplace

[see fig.2].

6. Fasten the Side Fillers to the fireplace using the two [2] existing holes on either side of the firebox opening.

7. Replace the Glass Door and put the new Valve Access Cover into place with angled ends to match Side Fillers.

NOTES: Cotton gloves must be worn to protect the finish during installation and handling.

All hand and finger marks must be cleaned off with a soft cloth and light detergent prior to applying heat to the unit.

Stainless panels may discolor a little during normal operation. This is normal and should not be considered a defect.

Page 51

Fan Installation MQRB4436 / MQRB5143 / MQRB6961

FAN KIT IS FOR USE IN BK (SINGLE SIDED) INSTALLATIONS ONLY

Fan Kit should be installed before the fireplace is placed into wall cavity. To remove fan for service, the burner pan must be removed and work done through the opening (See Burner System Removal section).

WARNING

Electrical Grounding Instructions

This appliance is equipped with a three prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this.

Before Servicing

1. Ensure all power supply is shut off.

2. Label all wires prior to disconnecting when servicing control. Wiring errors can cause improper and dangerous operation.

3. For fan servicing: Vacuum and clean lint/dirt build-up on the fan blades and motor.

4. When resealing the Burner Pan, use Millpac.

NOTE: If Fan Mount Tabs are not present, place fan as shown and mount with screws. Thermodisc must be

mounted under burner pan. If no place is provided, mount with a screw from the valve bracket.

!NOTE: Do not allow any power

cords or wires to come into contact with the firebox or the underside of the burner pan.

Fan Speed Control

(Locate Outside of Fireplace)

Thermodisc

(Located under Burner pan)

Page 52

Fan Speed Control Outside of Fireplace

If you plan to locate the variable speed control switch for the fan outside of the fireplace and you require a constant source of AC power inside the unit for another accessory such as lights or an IPI valve system, follow one of the procedures below.

WARNING WARNING WARNING

A qualified electrician must connect electrical wiring to junction outlet for built-in installation.

Follow all codes.

Caution: Electrical installation to be done by a qualified installer. All wires must be connected and grounded in accordance with

CSA Standard C22.1- Canadian Electrical Code part 1 or with the National Electrical Code, ANSI /NFPA 70 (latest edition) and /or in accordance with local codes.

Switch Controlled Split Receptacle With Switch At START Of Cable Run

Electrical Grounding Instructions – This appliance is equipped with a three – pronged (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle.

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation and servicing.

Switch Controlled Split Receptacle With Switch At END Of Cable Run

Page 53

MQRB4436 / MQRB5143 / MQRB6961 -Glass Ember Installation

Part Number

Description

MQG5W

Decorative Ember Glass - White - 5 lbs

MQG5A

Decorative Ember Glass – Azuria Blue - 5 lbs

MQG5C

Decorative Ember Glass - Copper - 5 lbs

MQEMBER

Glowing Ember Chunks

⚠ WARNING

 Pilot Shield and Pilot Area Must Not Be Covered, as delayed ignition can occur.  Do not change or substitute the glass ember material provided with this fireplace. If replacing, use

only replacement glass embers or MQEMBER available from your local authorized dealer.

Pilot Area Must Not Be Covered

*Pilot Shield should be visually inspected monthly for signs of deterioration due to flame exposure. Replace if necessary.

For best flame pattern it is essential to spread Crushed Glass or MQEMBER directly onto burner tube.

Ensure the glass embers do not excessively overlap as this will affect the flame pattern.

MQRB4436 / MQRB5143: (MQG5W) 5 lbs of ½” White Ember Glass is supplied with every unit.

MQRB6961: (MQG10W) 10 lbs of ½” White Ember Glass is supplied with every unit.

Use care when placing glass embers near the pilot area so as not block or have the glass fall over the crossover holes from the pilot to the burner, as delayed ignition can occur.

The following types of glass are approved (Use of any other type other than listed below can alter the performance of the unit and is not covered under warranty.):

Note: Use only 1/2” glass material on the burner.

 ½” Ember Glass Material from American Fireglass.

Maximum amount for MQRB4436: Natural Gas is 5 lbs, Propane units 5 lbs. Maximum amount for MQRB5143: Natural Gas is 10 lbs, Propane units 5 lbs. Maximum amount for MQRB6961: Natural Gas is 15 lbs, Propane units 10 lbs.

 Liquid Glass from Firegear.

Maximum amount for MQRB4436: Natural gas is 5 lbs, not recommended for Propane appliances. Maximum amount for MQRB5143: Natural gas is 10 lbs, not recommended for Propane appliances. Maximum amount for MQRB6961: Natural gas is 15 lbs, not recommended for Propane appliances.

Discoloration of glass media may occur if placed on the burner, this is not covered under warranty.

Page 54

Optional Driftwood & Rock Installation

Model

Part Number

Description

MQRB4436, MQRB5143, MQRB6961

MQRBD1

Drift Wood (x4) and Rocks (x4)

MQRB5143, MQRB6961

MQRBD2

Large 3pc Driftwood Set

MQRB4436, MQRB5143, MQRB6961

MQRock2

30pc Rock Set- Contemporary Collection- Natural

MQRB4436, MQRB5143, MQRB6961

MQRock3

30pc Rock Set- Contemporary Collection- Multi-Colored

MQRB4436, MQRB5143, MQRB6961

MQ Stone

Decorative Stones

MQRB4436, MQRB5143, MQRB6961

MQ46D

Driftwood Log Set, 3pcs. (Single Sided Units Only)

MQRB4436, MQRB5143, MQRB6961

RBCB1

Cannonballs - Assorted size and colors

MQRB4436, MQRB5143, MQRB6961

MQEMBER

Glowing Ember Chunks

MQRock2

MQRock3

with logs or rocks as sooting may occur.

MQRBD1

*Pilot Shield should be visually inspected monthly for signs of deterioration due to flame exposure. Replace if necessary.

⚠NOTE

 Pilot Area Must Not Be Covered, as delayed ignition can

occur.

 Do Not Cover any part of the burner tube with logs or rocks

as sooting may occur.

 For best flame pattern it is essential to spread supplied ½”

Crushed Glass or MQEMBER chunks directly onto burner tube.

NOTE: Only Crushed Glass or MQ Embers can be placed directly on Burner Tube.

MQRBD1 or MQRBD2 Driftwood and Rock Kit-

Place rocks and logs onto False Bottom randomly. MQ Rock2 or 3- 30pc Rock Set-

Place rocks onto False Bottom randomly.

MQ Stone Decorative Stone Set-

Place Stones onto False Bottom randomly. Do Not stack or overlay. Not all stones will be used on MQRB4436/5143 models.

Page 55

 MQ46D Driftwood Log Set- 3pcs. (Single Sided Units Only)

NOTE

 Pilot Area Must Not Be Covered, as delayed ignition can occur.  Be Careful Not To Cover Any Part Of The Burner Tube As

Cannonballs may become discolored or sooting may occur.

 For best flame pattern it is essential to spread supplied Crushed

Glass or MQEMBER directly onto burner tube.

 Place Log 1 on left side of fireplace against the back wall of the firebox.  Place Log 2 on the right side of fireplace against the back wall of the firebox and onto Log 1 as shown.  Place Log 3 in front of the burner in the center of fireplace as shown.

Can be used with MQ Glass, MQ Rock, MQ Stone or MQ Ember. Follow instructions for these accessories.

 RBCB1 Cannonballs - Assorted size and colors

Place randomly as desired inside fireplace (See NOTE above).

Can be used with MQ Glass, MQ Rock, MQ Stone or MQ Ember. Follow instructions for these accessories.

Page 56

Door and Glass Information

Glass Cleaning

It will be necessary to clean the glass periodically. During startup, condensation, which is normal, forms on the inside of the glass, and causes dust, lint etc. to cling to the glass surface.

Also, initial paint curing can deposit a slight film on the glass. It is therefore recommended that initially the glass be cleaned two or three times with a commercial fireplace glass cleaner. After that, the glass should be cleaned two or three times a season depending on the circumstances.

Cautions and Warnings

 Do not clean when the glass is hot.  The use of substitute glass will void all product warranties (see Glass Replacement in this section).  Care must be taken to avoid breakage of the glass.  Do not operate this fireplace without the glass front or with a broken glass front.  Do not strike or abuse the glass.

Glass Replacement

Only Robax ceramic or coated Neoceram glass may be used for replacement for Models MQRB4436, MQRB5143 and MQRB6169. Glass must be minimum 5mm thick.

To replace glass, clean all materials from the door frame. Scrape off old silicone all the way down to the metal. Using high-temp silicone [rated up to 500°F (260°C)] apply a continuous bead of approximately 1/8”-3/16” to all four [4] sides of the frame. With the frame resting on a flat surface, insert the new glass with a new gasket. Gently press the glass into the silicone. Be careful not to use excessive force on the glass. Let the silicone dry for approximately 15-20minutes.

Use caution when removing broken glass. Wear gloves.

Removal of the Glass Door

NOTE: A Door Latch Tool is provided to assist with removing and installing the glass doors. See next page.

1. Remove the door by unlatching the 2 top latches. Simply place 2 fingers in the grooves, and pull and lift upward slightly.

2. Once the top of the door is unlatched, tilt the door forward and lift upward to release the bottom.

3. When re-installing the door, place the bottom of the door into the door retainer slot and then secure the door with the top latches.

Spring Replacement

*Over time, the door latch spring (Part#36HB-123) may need to be replaced if tension is lost.

1. To replace latch spring, remove the 2 hex screws (located in the firebox) that secure the latch assembly in place.

2. Once the screws are removed the latches will slide out of place.

3. Remove the locknut from the latch assembly and replace the spring. Re-tighten the locknut until 2 thread turns are beyond the locknut. This is critical for proper tension. Replace latch assembly.

Latch Assembly 51MQ-123A

Page 57

Infinite Series Door Latch Tool MQRB4436 / MQRB5143 / MQRB6961

A Door Latch Tool is provided to assist with removing and installing the glass doors on the Infinite Series. While it is not necessary to use this tool, it may prove helpful.

Wait until unit is Completely

cool before touching glass or attempting to remove door.

- Fireplace Parts Are Removed for Clarity Only -

Step 1: Reach up into fireplace.

Step 3: Brace one hand between Tool and Glass.

Step 2: Grasp Latch with Tool.

Step 4: Draw Latch forward with other hand.

Step 5: Release Latch from Door.

Step 6: Release Tool from Latch.

Page 58

Valve Access Cover Removal

Remove Valve Access Cover in order to access igniter and valve controls. To remove Valve Access Cover, simply insert fingers into holes in Access Panel and lift out. When replacing Access Panel, engage Tabs into Slots in Bracket.

MQRB4436 / MQRB5143 / MQRB6961 Removable Lower Face Panel

Installers Note:

The Lower Face Panel on the valve side of the unit is shipped attached with only 3 screws for easy removal. This allows all necessary gas line and electrical connections to be made easily.

Once the installation is complete attach the Lower Face Panel with the supplied screws. The Lower Face Panel must be on the unit Before Facing Materials are applied.

Note: Once Facing Materials are applied, removal of the Lower Face Panel will not be possible.

Page 59

Gas Line Installation

This gas appliance should be installed by a qualified installer in accordanc e with local building codes and with current CAN/CSA - B149.1 or .2 installation codes for Gas Burning appliances and equipment in Canada and the National Fuel Gas Code ANSI Z223 in the U.S.A.

1. The gas pipeline can be brought in through either the left side or the bottom of the appliance. A knockout i s provided at either l

ocation to allow for the gas pipe installation and testing of any gas

connection.

2. The gas control inlet is 3/8” NPT. Typical installation layout for rigid pipe is shown at right.

3. When using copper or flex connector, use only approved fittings. Always provide a union so that gas line can be easily disconnected for burner or fan servicing. See gas specification for pressure details and ratings.

4. When a vertical section of gas pipe is required for the installation, a condensation trap is needed. See CAN/CSA-B149.1 or .2 for code details.

5. For natural gas, a minimum of 1/2” iron pipe with gas minimum pressure of 5.5” w.c. must be used for supply from the gas meter. Consult with the local gas utility if any questions arise concerning pipe sizes.

6. Ports are accessible for test gauge connection both on the inlet and outlet of the gas valve.

7. Turn the gas supply ON and check for leaks. DO NOT USE OPEN FLAME FOR THIS PURPOSE. Use an approved leak testing solution.

8. The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2psig [3.5 kPa].

9. The appliance must be isolated from the gas supply piping system by closing its individual shutoff valve during any pressure

testing of the gas supply piping system at test pressures equal to or less than 1/2psig [3.5 kPa].

NOTE: The gas line connection may be made of 1/2” rigid pipe or an Approved Kingsman Flex Connector, such as FP15GC.

Since some municipalities have additional local codes, it is always best to consult your local authorities and the current

CAN/CGA - B149.1 or .2 installation code in Canada or the National Fuel Gas code ANSI Z223.1 in the U.S.A

Warning: When purging the gas line, the glass front must be removed.

IMPORTANT: Always check for gas leaks with a soap and water solution. DO NOT USE OPEN FLAME FOR LEAK TESTING.

Do not alter the gas orifice.

Gas Specifications

Models MQRB4436N MQRB4436LP MQRB5143N MQRB5143LP MQRB6961N MQRB6961LP

Fuel Gas Control Millivolt

Maximum Input 22,000 Lo /

Orifice Size (04500ft)

Air Shutter Gas Inlet Size Gas Supply

Pressure Natural Gas Propane Manifold

Pressure High Manifold

Pressure Low

Natural Gas Propane Natural Gas Propane Natural Gas Propane

Adjustable

33,000 Hi

Millivolt Adjustable

26,000 Lo / 33,000 Hi

Millivolt Adjustable Millivolt Adjustable 28,000 Lo / 40,000

31,000 Lo / 40,000 Hi

Millivolt Adjustable

43,000 Lo / 62,000 Hi

Millivolt Adjustable

49,000 Lo /

62,000 Hi #33 #49 #30 #46 #34 x 2 #49 x 2 3/32” Full Open 1/32” 3/8” 1/16” Full Open

S.I.T. 820 Nova, 3/8” NPT

Minimum Normal Maximum

5.5” 7” 9” 11” 11” 12”

3.5” w.c. [0.87kPa] NG 10” w.c. [2.61kPa] LP

1.6” w.c. [0.40kPa] 6.3” w.c. [1.57kPa]

Page 60

Millivolt System, Lighting, and Burner Control

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property

damage, personal injury or loss of life.

A This appliance has a pilot which must be lighted by hand. When

lighting the pilot, follow these instructions exactly.

B Smell all around the appliance area for gas. Be sure to smell next

to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

 Do not try to light an appliance.  Do not touch any electrical switch; do not use any phone in your

building.

LIGHTING INSTRUCTIONS

1. Stop! Read the safety information above this label.

2. Set the thermostat to lowest setting.

3. Turn off all electrical power to the appliance.

4. Locate valve under the burner assembly.

5. If the control knob is not already in the off position, i.e. the word “OFF” in the 9 o’clock position, then push in the gas control knob slightly and turn  clockwise to “OFF”. NOTE: Knob cannot be turned from “PILOT” to “OFF” unless knob is pushed in slightly. Do not use force.

6. Wait five [5] minutes to clear out any gas. If you then smell gas. STOP! Follow “B” in the safety information above on this label. If you don’t smell gas then go to the next step.

7. Now push in the control knob slightly and turn  counter-clockwise to the “PILOT” position.

8. Push in the control knob all the way and hold it. With the other hand push in the red igniter button until you hear a click. Now observe closely the pilot burner located on the rear center-left hand side of the main burner.

TO TURN OFF THE APPLIANCE

1. Set the thermostat to lowest setting.

2. Turn off all electric power to the appliance if service is to be performed.

3. Open the control access door.

NOTE: Only one on/off device (manual on/off, remote control, or hard wired thermostat) should be connected to the appliance at any one time, this is most important when installing a insert or stove as the on/off rocker switch is installed at the factory.

BEFORE LIGHTING

 Immediately call your gas supplier from a neighbour’s phone. Follow the

gas supplier’s instructions.  If you cannot reach your gas supplier, call the fire department. C Use only your hand to push or turn the gas control knob. Never use

tools. If the knob will not push in or turn by hand, don’t try to repair it.

Call a qualified technician. Force or attempted repair may result in a fire

or explosion. D Do not use the appliance if any part has been under water. Immediately

call a qualified service technician to inspect the appliance and to

replace any part of the control system which has been under water.

If a flame has appeared then continue to depress the control knob for 20 seconds. If the flame did not appear then continue to depress the red igniter button every 5 seconds until a flame is established. NOTE: If after 30 seconds a flame has not yet been established then turn the control knob back to the off position and repeat steps 5, 6 & 7.

9. Once the pilot has been established hold the control knob in the

depressed position for approximately 25 seconds before releasing. If

the flame goes out then repeat steps 7 and 8.

 If the knob does not pop up when released, stop and immediately call

your service technician or gas supplier.

 If the pilot will not stay lit after several tries, turn the gas control to

“OFF” and call your service technician.

10. Now turn the control knob to the “ON” position. The burner will not light

unless the wall switch thermostat or remote control is turned “ON” or in

the case of the thermostat there is a call for heat.

11. Close the access door and turn all electrical power back to the

appliance.

12. The pilot must be turned off when the unit is not in use.

4. Push in the gas control knob slightly and turn  clockwise to the “OFF”

position. Do not force.

5. Replace control access panel.

Recommended Maximum Lead Length (Double Wire)

When Using Wall Switch or Thermostat

Wire Size Max. Length

14ga 100ft [30.4m] 16ga 64ft [19.5m] 18ga 40ft [12.1m] 20ga 25ft [7.6m] 22ga 15ft [4.5m]

CAUTION: DO NOT WIRE 120V POWER TO

MILLIVOLT SWITCHES OR THERMOSTAT.

*In the U.S.A. Thermostats are not permitted for Vented Gas Fireplaces (ANSI Z21.50b-2009 -Decorative).

To Wall Switch, Thermostat*, Or Remote Receiver

Page 61

Troubleshooting the Gas Control System

WARNING

BEFORE DOING ANY GAS CONTROL SERVICE WORK, REMOVE THE GLASS FRONT. Before troubleshooting the gas control system, be sure external gas shut off is in the "On" position.

Problem Possible Causes Corrective Action

Spark igniter will not light.

Pilot will not stay lit after carefully following lighting instructions.

Pilot burning, no gas to burner, valve knob “ON”, and wall switch “ON”.

Frequent pilot outage problem.

Flame lifts off burner and goes out in less than 30 seconds.

Flame lifts off burner on one side while the rest of the flame remains lit.

Defective or misaligned electrode at pilot.

Defective igniter (pushbutton).

Defective thermocouple (flame switch where applicable).

Defective valve magnet. Replace valve, if pilot won't hold after the thermocouple is replaced.

Wall switch or wires defective.

Generator may not be generating sufficient voltage.

Plugged burner orifice. Check burner orifice for stoppage and remove.

Defective automatic valve operator.

Pilot flame may be too low or blowing (high) causing the pilot safety to drop out.

The inner liner has come off flue or termination, flame is starving for oxygen.

Improper installation of firebrick. Firebrick is likely leaning.

Check for spark at electrode and pilot: if no spark and electrode wire is properly connected, replace igniter.

Using a match, light pilot. If pilot lights, turn off pilot and push the red button again. If pilot will not light - check gap at electrode and pilot should be 1/8" to 1/4" to have a strong spark.

Check pilot flame. Must impinge on generator and thermocouple. Clean and/or adjust pilot for maximum flame impingement on generator and thermocouple. Replace thermocouple if pilot will not hold. (Hand tight 1/8 turn on replacement)

Check wall switch and wires for proper connections. Jumper wire across terminals at wall switch. If burner comes on, replace defective wall switch. If okay, jumper wires, across wall switch wires at valve. If burner comes on, wires are faulty or connections are bad.

Check generator with millivolt meter. Take reading at generator terminals of gas valve. Should read 325 millivolts minimum while holding valve knob depressed in pilot position and wall switch "off" Replace faulty generator if reading is below specified minimum.

Remove wall switch wires from gas valve. Install jumper wires from top bottom terminals of gas valve. Turn valve on "ON". If main burner does not light, replace valve.

Clean and/or adjust pilot flame for maximum flame impingement on generator and thermocouple.

Attach the inner liner to flue or termination using screws, silicone and clamps as stated in manual.

Be sure to position firebrick against firebox walls and be sure to use brick clips attached to the inner side of firebox.

Page 62

Burner System Maintenance- MQRB4436 / MQRB5143 / MQRB6961

It is recommended to annually inspect and clean the Burner System to prevent malfunction and / or sooting. This operation should be performed by your dealer or a qualified technician.

-CAUTION-

Before servicing the burner system ensure that the gas supply is turned OFF and disconnect all electrical connections to the appliance. Allow the appliance to cool to room temperature. Note that the pilot assembly may be hot in an intermittent or standing-pilot system—even if the main burner was never on. Exercise caution when working within the area.

-ALL WORK SHOULD BE PERFORMED BY A QUALIFIED AND CERTIFIED TECHNICIAN-

Monthly Flame Inspection

It is recommended to turn on the unit at least once a month and inspect the flame pattern to ensure there are no problems with the burner tube (Flame should appear similar to the above picture).

The pilot flame should also be inspected monthly to ensure proper operation.

Pilot Must Maintain This

Relationship With Burne

Pilot Area Must Not Be Covered.

*Pilot Shield should be visually inspected monthly for signs of deterioration due to flame exposure. Replace if necessary.

Page 63

Gas Conversion for Top Convertible Pilot (Series 019065X) – PART B

Instructions for converting SIT 190 series pilot burner injection from NG to LPG and from LPG to NG only . This information should be considered as supplemental to the Appliance Manufacturer’s Instructions.

WARNING: The installation of this conversion kit must only be undertaken by a qualified and certified gas

appliance installer.

1. Shut off the gas supply to the appliance.

2. Allow the pilot burner to cool to room temperature.

WARNING: Touching a hot pilot burner can result in injury.

3. The pilot hood is held in place by spring pressure. Remove the hood by pulling it directly up from the pilot bracket (a).

4. Insert a 5/32” or 4mm Allen wrench into the hexagonal key-way of the injector (b), and rotate it  counter-clockwise until it is free of the injector journal (c).

5. Verify that the new injector is proper for the application. The injector size is stamped on the side of the injector near the top. LPG injectors have a groove machined around their circumference near the top, while NG injectors do not have a groove (e). Refer to the Appliance Manufacturers instruction sheet for the proper injector size.

6. Insert the Allen wrench into the end of the injector. Then, insert into injector journal, and rotate the injector clockwise until a torque of 9 in-lbs is achieved.

7. Replace the pilot hood by aligning the tab on the base of the hood with the slot in the side of the pilot journal, and push the hood down, directly onto the pilot bracket (d). The hood must sit squarely on the bracket for proper operation. Check to insure that the hood is properly seated onto the pilot bracket.

(a)

(c)

(b)

(d)

(e)

WARNING: This conversion kit must only be applied as part of a conversion kit supplied by the appliance

Manufacturer for the specific appliance, and type of gas being converted. INSTALLER NOTICE: These instructions must be left with appliance.

Page 64

ARNING!-

Gas Conversion for Modulator – PART C

ARNING!-

Page 65

MQRB4436 Burner Section: Gas Conversion

Models: MQRB4436N, MQRB4436LP, MQRB4436NE, MQRB4436LPE.

Kit Number

4436MQ-CKLP LP Conversion

4436MQ-CKNG NG Conversion

4436MQ-CKLPI LP Conversion

4436MQ-CKNGI NG Conversion

IMPORTANT: Always check for gas leaks with a soap and water solution. DO NOT USE OPEN FLAME FOR LEAK TESTING.

Description Pilot Orifice Burner Orifice

Brass (1000-255)

-Millivolt-

-IPI-

1001-P167SI

#30 (977.167)

1001-P165SI

#51 (977.165)

1001-P168SI

#35 (977.168)

1001-P166SI

#62 (977.166)

#49 1000-253closed Full

#33 1000-253closed 3/32” 1001-P201SI

#49 1000-253closed Full

#33 1000-253closed 3/32” 1002-P016SI

Brass Nipple Air Shutter Hi/Lo Regulator

1001-P202SI

Open

(0.907.202)

(0.907.201)

1002-P014SI

(0.907.014)

(0.907.016)

Caution:

The gas supply shall be shut off prior to disconnecting the electrical power, before proceeding with the conversion.

1. The Burner Tube must be removed from the Burner Pan Assembly (See Burner Tube Removal). Adjust the Air Shutter to the correct Primary Air setting as specified in the manual or on the label plate. To adjust the Primary Air setting, loosen screw on the side of the Air Shutter and rotate to the correct opening using a drill bit or tape measure. Retighten screw.

2. Remove the Main Orifice using a ½” wrench and replace

Pilot Must

Maintain This

Relationship With Burner.

with the new Conversion Orifice which came with the Conversion Kit.

3. Replace the Burner Tube. Install the new Pilot Orifice (See

Pilot Conversion) and Hi/Lo valve regulator by following instructions supplied with the Conversion Kit.

Refer to “Gas Specifications Chart” for inlet pressures and input ratings. Clock meter to verify input rate. Place conversion label as close to converted gas control as possible. Refer to lighting instructions to verify the normal operating sequenc e of the ignition system.

-Warning-

This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer's instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or production of carbon monoxide may result causing property damage, personal injury or loss of life. The qualified service agency is responsible for the proper installation of this kit. The installation is not proper and complete until the operation of the converted appliance is checked as specified in the manufacturer's instructions supplied with the kit.

Page 66

MQRB5143 Burner Section: Gas Conversion

Models: MQRB5143N, MQRB5143LP, MQRB5143NE, MQRB5143LPE.

Kit Number

5143MQ-CKLP LP Conversion

5143MQ-CKNG NG Conversion

5143MQ-CKLPI LP Conversion

5143MQ-CKNGI NG Conversion

IMPORTANT: Always check for gas leaks with a soap and water solution. DO NOT USE OPEN FLAME FOR LEAK TESTING.

Description Pilot Orifice Burner Orifice

Brass (1000-255)

-Millivolt-

-IPI-

1001-P167SI

#30 (977.167)

1001-P165SI

#51 (977.165)

1001-P168SI

#35 (977.168)

1001-P166SI

#62 (977.166)

#46 1000-253closed 3/8” 1001-P202SI

#30 1000-253closed 1/32” 1001-P201SI

#46 1000-253closed 3/8” 1002-P014SI

#30 1000-253closed 1/32” 1002-P016SI

Brass Nipple Air Shutter Hi/Lo Regulator

(0.907.202)

(0.907.201)

(0.907.014)

(0.907.016)

Caution:

The gas supply shall be shut off prior to disconnecting the electrical power, before proceeding with the conversion.

2. Remove the Main Orifice using a ½” wrench and replace with the new Conversion Orifice which came with the Conversion Kit.

3. Replace the Burner Tube. Install the new Pilot Orifice (See

Pilot Conversion) and Hi/Lo valve regulator by following instructions supplied with the Conversion Kit.

-Warning-

Pilot Must

Maintain This

Relationship With Burner.

Page 67

MQRB4436 / MQRB5143 Burner Tube Removal

1. Remove the six [6] DT screws from the lower portion of the Burner Tube Mount Brackets.

2. Slide the Burner Tube away from the Plumbing Connection until it disengages from the orifice.

3. Reverse these steps to reinstall.

MQRB4436 / MQRB5143 Burner System Removal/Installation Guide

-Warning-

Turn off Unit and allow to cool before cleaning. Only a Qualified service technician

should service and repair this appliance.

1. Lift off Valve Access Cover. Remove Valve Heat Shield.

2. Remove the Glass Door from the unit. Loosen Liner Clips in Firebox Top & remove End Panels. Remove DT screws and lift out the False Bottom.

3. Remove the DT screws around the perimeter of the burner pan.

4. Carefully work the burner pan loose & lift the assembly upward to remove it from the firebox cavity.

5. Installation is the reverse of these steps. Ensure that the mounting surface is clean & fresh Black Mill Pac is used to reseal the burner pan.

Page 68

MQRB4436 / 5143 / 6961 Moving Valve to Other Side of Fireplace

Warning: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically

approved with this appliance may result in property damage or personal injury.

The Valve Assembly may be changed to the other side of the fireplace. This must be done Before

1. Remove the Burner Tube (See Burner Tube Removal section in

this Manual).

2. Disconnect plumbing from the valve, including connections to Pilot. Remove the [4] DT screws in the burner pan which hold the Valve System in place. Reinstall with the Valve System on the other side of the fireplace. Note that as stated in Fig.2, the millivolt valve system can be transferred to the right side without rotation, while the

IPI valve system must be rotated 180° for proper operation on the right side of the unit.

Note: Take care not to damage the

pilot tube during this operation. MQRB6961:Wires and plumbing must

not interfere with explosion damper assembly.

Reconnect plumbing, along with Pilot.

These connections must be leak tested.

3. Remove the Electrical Box and

Light Power Bus Module (and IPI Module & IPI Shield if used), and locate these items to the other side of the unit. Refer to Fig.3 & Fig.4 below.

4. Replace the Burner Tube.

the unit is inside the enclosure.

Fig.1

Fig.2

Fig.3 Right Hand Millivolt Valve

Fig.4 Right Hand IPI Valve

Page 69

MQRB6961 Burner Section: Gas Conversion

Models: MQRB6961N, MQRB6961LP, MQRB6961NE, MQRB6961LPE.

Kit Number

6961MQ-CKLP LP Conversion

6961MQ-CKNG NG Conversion

6961MQ-CKLPI LP Conversion

6961MQ-CKNGI NG Conversion

IMPORTANT: Always check for gas leaks with a soap and water solution. DO NOT USE OPEN FLAME FOR LEAK TESTING.

Description Pilot Orifice Burner Orifice

Brass (1000-255)

-Millivolt-

-IPI-

1001-P167SI

#30 (977.167)

1001-P165SI

#51 (977.165)

1001-P168SI

#35 (977.168)

1001-P166SI

#62 (977.166)

#49 x 2 1000-253closed Full Open 1001-P202SI

#34 x 2 1000-253closed 1/16” 1001-P201SI

#49 x 2 1000-253closed Full Open 1002-P014SI

#34 x 2 1000-253closed 1/16” 1002-P016SI

Brass Nipple Air Shutter Hi/Lo Regulator

(0.907.202)

(0.907.201)

(0.907.014)

(0.907.016)

The gas supply shall be shut off prior to disconnecting the electrical power, before proceeding with the conversion.

1. The Burner Tube must be removed from the Burner Pan Assembly (See Burner Tube Removal). Adjust the Air Shutters to the correct Primary Air setting as specified in the manual or on the label plate. To adjust the Primary Air setting, loosen screw on the side of the Air Shutter and rotate to the correct opening using a drill bit or tape measure. Retighten screw.

2. Remove both Main Orifices using a ½” wrench and replace with the new Conversion Orifices which came with the Conversion Kit.

3. Replace the Burner Tube. Install the new Pilot Orifice (See Pilot Conversion) and Hi/Lo valve regulator by following instructions supplied with the Conversion Kit.

Caution:

Pilot Must

Maintain This

Relationship With Burner.

-Warning-

Page 70

MQRB6961 Burner Tube Removal

Air Shutte

1. Remove the six [8] DT screws from the lower portion of the Burner Tube Mount Brackets.

2. Slide the Burner Tube away from the Plumbing Connection until it disengages from the orifices.

3. Reverse these steps to reinstall. MQRB6961- Installer’s Note: If flames appear higher or lower at one end of the unit, the primary air can be

adjusted on one of the two mixing sleeves to even the flame. Closing the air shutter slightly will result in a taller flame on that side of the fireplace.

MQRB6961 Burner System Removal/Installation Guide

-Warning-

Turn off Unit and allow to cool before cleaning. Only a Qualified service technician

should service and repair this appliance.

1. Remove Valve Heat Shield.

2. Remove the Glass Door from the unit. Loosen Liner Clips in Firebox Top & remove End Panels. Remove DT screws and lift out the False Bottom.

3. Remove the DT screws around the perimeter of the burner pan.

4. Carefully work the burner pan loose & lift the assembly upward to remove it from the firebox cavity.

5. Installation is the reverse of these steps. Ensure that the mounting surface is clean & fresh Black Mill Pac is used to reseal the burner pan.

Page 71

Remote Receiver Location

For GT Series Remotes Only

The Remote Receiver may be located inside of the unit- several inches to the left of the valve and near the front of the appliance.

The Remote Receiver MUST covered by the DCHS (Remote Control Heat Shield- see Parts List in manual).

For All IPI Installations & GT Series Remotes Only

The Remote Receiver may be located outside of the unit- up to a maximum of 6 feet from either side of the fireplace. An Extension Harness (Part No. 1001-P904SI) is required.

The face of the Remote Receiver must be accessible for programming the remote as well as changing the batteries.

[Steel Stud Framing Shown.]

IPI Electronic Ignition System

In the event of an operational lockup the IPI system must be reset by removing the batteries

from both the backup pack and the remote receiver module.

SYSTEM NOTE:

Page 72

51-UHS For Infinite Series MQRB4436, MQRB5143, MQRB6961

The 51-UHS is designed for millivolt and IPI Infinite units for in-unit installation of the Remote Receiver, Fan Control Module, and the IPI Module.

NOTE: When using GTF Fan Module, the 51UHS must be used.

Remote Receiver

IPI Module

Fan Control Module

51-UHS can be inserted & removed from beneath fireplace through access panel opening (Remove

glass door first).

NOTE: The gas

line connection may be made of 1/2” rigid pipe or

an Approved

Kingsman Flex

Connector, such

as FP15GC.

Since some

municipalities

have additional local codes, it is

always best to

consult your local

authorities and

the current

CAN/CGA -

B149.1 or .2 installation code in Canada or the

National Fuel Gas

code ANSI

Z223.1 in the

U.S.A

Z36 FAN

51-UHS

(See Each Section For Connections & Wiring)

BATTERIES

Batteries for Remote Receiver can be changed by lifting 51-UHS

COMPONENT LOCATIONS

VALVE

up through opening.

LAMP

TRANSFORMER

ASSEMBLY

POWER

VENT

CONTROL

MODULE

120 VAC

51-UHS MUST BE ACCESSIBLE

GAS LINE ROUTING OPTIONS

Page 73

IPI Electronic Ignition System

Overview

The IPI system is an advanced burner controller that provides you with the option of having either a StandingPilot, or an intermittent igniting system. This alternating mode is controlled by the CPI/IPI Switch (Continuous Pilot Ignition/Intermittent Pilot Ignition) located on the IPI System Box. The difference between a Standing-Pilot and an Intermittent-Pilot is in whether the pilot stays lit or shuts off:

In Standing-Pilot, the pilot assembly is lit by the IPI Main Module and continues to stay lit until 1) the CPI/IPI Switch is switched to the IPI position; 2) a loss of electrical power (battery and AC source), 3) the flame sensor loses its signal,

4) the fuel supply discontinues, or 5) the IPI Main Module malfunctions.

In the Intermittent-Pilot mode, the pilot shuts off when the appliance is not in use. The advantage of this mode is that fuel is not consumed when the fireplace is not operating.

NOTE: In some jurisdictions Intermittent-Pilot is required. That means the pilot cannot remain lit when the appliance is not operating.

Components

The co Valve. With these two components the system is able to operate a gas fireplace. There are also other components available to complement the IPI system.

re of the IPI system is the Main Module and the IPI

UHS

Box

Cover

Backup

Battery

ack

Remote

ceiver

Module

CPI / IPI

Switch

IPI Module

Fan Control Module

C Adapter

Plug In

IPI System Cover

: Is essential in keeping the components at their proper operating temperatures. DO NOT OPERATE THE APPLIANCE WITHOUT THIS COVER.

Modulating Servo Motor

: Is an add-on valve component that permits HI/LO functionality to be controlled by the remote. Contrary to this feature is a Manual HI/LO Control Knob. The Modulating Servo Motor requires the Remote system to be present.

Backup Battery Pack

: This component permits the IPI system to operate without the need for an external AC Adapter power source. The advantage to using the battery backup is that in the case of a power failure, the appliance is still operable.

NOTE: In certain instances the IPI Main Module requires resetting. This can occur if the system is unable to ignite the pilot or the main burner in the allotted time period. The IPI is programmed to lockout all commands. To reset this lockout you must deplete the system of all electrical power. This means to remove the batteries from the Battery Pack, remove the batteries from the Remote Receiver (if applicable), and disconnect the AC Adapter from the system. Leave the power off for approximately 25 seconds to clear its lockout.

Remote Receiver: This component provides the capability of controlling the appliance with a wireless remote tran smitter.

Standing Pilot Mode for Colder Climates (Below Freezing)

For IPI models it may be necessary to set the appliance to Standing Pilot mode to maintain heat in the cavity. The purpose of this

procedure is to prevent cold air from penetrating the chimney and then onto the living space. Therefore, when the internal

temperature is slightly elevated the fireplace is able to freely exhaust its combustion and hence makin g i t easier to startup.

Page 74

-Remote Control Operation-

The Proflame GTM is configured to control the on/off main burner operation, its flame levels, and provides on/off and Smart thermostatic control of the appliance.

Transmitter

The Transmitter is powered by 3 AAA type batteries. A Mode Key is provided to Index between the features and a Thermostat Key is used to turn on/off or index through thermostat functions

Remote Receiver

The Receiver connects directly to the gas valve and stepper motor with a wiring harness. The Receiver is powered by 4 AA type batteries. The Receiver three position slider switch can be set to one of three positions: ON (Manual Override), Remote (Remote control) or Off.

Initializing the System for the first time

Install 4 AA batteries into the receiver battery bay. Install 3 AAA type batteries in the Transmitter battery bay. Place the 3 position slider switch in the “Remote” position. Insert the end of a paper clip into the hole marked “PRG” on the Receiver front cover. The Receiver will “beep” three (3) times to indicate that it is ready to synchronize with a Transmitter. Push the On button. The Receiver will “beep” four times to indicate the Transmitter’s command is accepted. The system is now initialized.

Temperature indication Display

With the system in the “OFF” position, press the Thermostat Key and the Mode Key at the same time. Look at the LCD screen on the Transmitter to verify that a C or F is visible to the right of the Room Temperature display.

Turn the Appliance On or Off

Press the ON/OFF Key on the Transmitter

Remote Flame Control

The Proflame GTM has six (6) flame levels. Pressing the Down Arrow Key once will reduce the flame height by one step until the flame is turned off. The Up Arrow Key will increase the flame height each time it is pressed. If the Up Arrow Key is pressed while the system is on but the flame is off, the flame will come on in the high position.

NOTE: The Remote

Receiver module can also

be located outside of the

appliance to a maximum of

6ft away installed in a

certified deep wall switch

electrical box (2-3/4”

depth). For this

configuration an extension

wiring harness (P/N: 1001-

P904SI) is required.

Remote Receiver

Room Thermostat ( Transmitter Operation)

The Remote Control can operate as a room thermostat. To activate this function, press the Thermostat Key. The LCD display on the Transmitter will change to show that the room thermostat is “ON” and the set temperature is now displayed. To adjust the set temperature, press the Up or Down Arrow Keys until the desired set temperature is displayed on the LCD screen of the Transmitter.

Smart Thermostat (Transmitter Operation)

The Smart Thermostat function adjusts the flame height in accordance to the difference between the set point temperature and the actual room temperatures. As the room temperature gets closer to the set point the Smart Function will modulate the flame down. To activate this function, press the Thermostat Key until the word "SMART" appears to the right of the temperature bulb graphic. To adjust the set temperature, press the Up or Down arrow Keys until the desired set point temperature is displayed.

Key Lock Function

This function will lock the keys to avoid unsupervised operation. To activate this function, press the MODE and the UP Arrow Key at the same time. To de-activate this function, press the MODE and the UP Arrow Key at the same time.

Low Battery Detection Transmitter - When the Transmitter batteries are low, a

Battery Icon will appear on the LCD display of the Transmitter. Receiver - When the Receiver batteries are low, No “beep” will be emitted from the Receiver when it receives an On/Off command from the Transmitter. When the batteries are replaced the “beep” will be emitted from the Receiver when the ON/OFF Key is pressed (See Initializing the System for the first time).

Manual Bypass Of The Remote System

If the batteries of the Receiver or Transmitter are low or depleted, the appliance can be turned on manually by sliding the three position slider switch on the Receiver to the ON position. This will bypass the remote control feature and the appliance main burner will come on if the gas valve is in the “On” position.

*In the U.S.A. Thermostats are not permitted for Vented

Gas Fireplaces (ANSI Z21.50b-2009 -Decorative).,

Page 75

IPI Electronic Ignition Parts List – Standard System

ITEM NO. PART NO. DESCRIPTION

1 1006-P002si Valve IPI Hi/Lo NG 1006-P003si Valve IPI Hi/Lo LP 2 *1002-P047si Pilot Assembly-LP -24” Wire *1002-P033si Pilot Assembly-NG -24” Wire 3 1002-P017si Spark Electrode (with wire) *1002-P119si Spark Electrode (with wire- 35” Length) 4 1002-P903si Electrode Flame Sensor *1002-P910si Electrode Flame Sensor (35” Length) 5 1002-P302si IPI Ignition Board 6 1002-P850si AC Wall Adapter 7 1002-P12BH Battery Pack 8 1002-P912si Wiring Harness 9 1001-P166si Orifice Pilot -NG#62 1001-P168si Orifice Pilot -LP#35 10 1002-P013si Stepper Motor -NG 1002-P012si Stepper Motor -LP 1002-P016si Hi/Lo Regulator -NG 1002-P014si Hi/Lo Regulator -LP *Models ZRB46E / MQRB4436E / MQRB5143E / MQRB6961E Longer (35”) Wire length is required for these units.

Proflame System Configuration: Manual Hi/Low Simplified Wire Diagram

0.886.002

-OR-

0.886.003

Page 76

Configuration #1: Basic manual HI/LO and manual ON/OFF capabilities.

Page 77

Receiver Module

.584.523/521/221 1001-P221SI

Receiver Module .584.523/521/221 1001-P221SI

Page 78

Operating the Receiver Without Batteries For GT / EGT / GTM / EGTM Remote Controls

-Wiring Harness P/N 1002-P906si required for both IPI & Millivolt systems.

-Millivolt Systems will also require Power Adapter P/N 1002-P850si.

The Remote Receiver & IPI or Millivolt system can be powered by the AC Adapter. This is advantageous if you do not want to use batteries. Simply connect the AC Adapter into the Remote Control Wiring Harness as per the diagrams below.

IPI System EGTM

Millivolt System GTM

Receiver Module

0.584.523/521/221 1001-P221SI

Receiver Module

0.584.523/521/221 1001-P221SI

*In the U.S.A. Thermostats are not permitted for Vented

Gas Fireplaces (ANSI Z21.50b-2009 -Decorative).

Page 79

Configuration #3: Remote ON/OFF, variable HI/LO, and fan capabilities. Refer to the fan installation/removal section for fan

installation.

Page 80

Electronic Ignition Lighting Instructions

If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or

loss of life.

Always light the pilot whether for the first time or if the gas supply has ran out with the glass door opened or removed.

FOR YOUR SAFETY READ BEFORE LIGHTING:

A. This fireplace is equipped with an ignition device which automatically lights the pilot. Do not try to light by hand. B. Before operating smell all around the fireplace area for gas and next to the floor because some gas is heavier than

air and will settle on the floor.

C. Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect

the fireplace and replace any part of the control system and any gas control which has been under water.

WHAT TO DO IF YOU SMELL GAS:

• Turn off all gas to the fireplace.

• Open windows.

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire department.

LIGHTING INSTRUCTIONS

1. Stop! Read the above safety information on this label.

2. Remove batteries from receiver, and/or Battery Backup Pack.

3. Turn off all electric power to the fireplace.

4. This fireplace is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand.

Open the glass d

6. Turn manual shutoff valve clockwise

7. Wait five (5) minutes to clear out any gas. If you smell gas including near the floor, STOP! Follow “B” in the above safety information on this label. If you don’t smell gas go to the next step.

8. Turn manual shutoff valve counter-clockwise

9. Close the glass door.

10. Turn on all electric power to the fireplace and re-install batteries into the Transmitter/Receiver, and/or Battery Backup Pack.

11. Turn “On” Switch that operates the Main Burner. If using a Remote Control refer to Remote Control Operation Manual for activation.

oor.

to off (Located behind the access panel).

to on.

TO TURN OFF GAS

1. Turn off all electric power to the fireplace if service is to be performed, including removing batterie s from Re mote Transmitter/Receiver and/or Battery Backup Pack.

2. Access door inside the firebox must be removed to access the manual shutoff valve.

3. If alternate shut-off valve was installed it can be shutoff instead of going through the fireplace to access the

fireplace shut off valve.

Page 81

LK2 Halogen Lamp Kit MQRB4436 / MQRB5143

Please follow the current ANSI/NFPA 70 National Electrical Code in the USA and CAN/CSA C22.1 Canadian National

Electrical Code in Canada.

SYSTEM NOTES

1. Each lamp is running on a dedicated circuit (Parallel circuit). This means that if one bulb fails the other will remain operational.

2. Switch circuit is on low voltage side of transformer.

3. Solid-state transformer is designed to run halogen lamps ONLY.

4. To remove leads from the 6 port terminal, simply insert a pin to release the grip on the wire.

Note: Lightbulbs NOT covered under Warranty.

This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.

WARNING

Electrical Grounding Instructions

Page 82

LK3 Halogen Lamp Kit (MQRB6961)

Please follow the current ANSI/NFPA 70 National Electrical Code in the USA and CAN/CSA C22.1 Canadian National

Electrical Code in Canada.

SYSTEM NOTES

1. Each lamp is running on a dedicated circuit (Parallel circuit). This means that if one bulb fails the rest will remain operational.

2. Switch circuit is on low voltage side of transformer.

3. Solid-state transformer is designed to run halogen lamps ONLY.

4. To remove leads from the 6 port terminal, simply insert a pin to release the grip on the wire.

Note: Lightbulbs NOT covered under Warranty.

WARNING

Electrical Grounding Instructions This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.

Page 83

Venting

WARNING: WHEN THE

HORIZONTAL VENT TERMINATION

IS ACCESSIBLE A CERTIFIED

GUARD (SAFETY CAGE) SHALL BE

INSTALLED.

Notes:

1) Clearances are to the edge of the terminal plate. Add 6-3/4” for MQRB4436 & MQRB5143, and 8-1/8” for MQRB6961 to arrive at centerline.

2)Local codes or regulations may require different clearances.

A. Clearance above grade, veranda, porch, deck, or balcony 12in [30cm] min. B. Clearance to window or door that may be opened. 12in [30cm] min. for appliances 100,000BTUh [30kW] and lower, in Canada.

[2]

[23cm] for appliances 50,000 BTUh and lower, in USA.

9in

C. Clearance to permanently closed window min. 12in [30cm] recommended to prevent condensation on window, in Canada. 9in

[23cm] for appliances 50,000 BTUh and lower, in USA.

D. Vertical clearance to ventilated soffit located above the termination within a horizontal distance of 2ft [60cm] from the center line of

the termination. 4436MQRB / 5143MQRB-18in [46cm] min, 6961MQRB- 24in [61cm] min. E. Clearance to unventilated soffit 4436MQRB / 5143MQRB-12in [30cm] min, 6961MQRB-24in [61cm] min. F. Clearance under veranda, porch, deck or balcony 12in [30cm] min.

[3]

G. Clearance from a perpendicular inside wall or outer corne r to the edge of the vent terminal plate is 3in [7.6cm] min. H. Clearance to each side of center line extended above meter/regulator assembly 3ft [91cm] within a height 15ft [4.5m] above the

meter/regulator assembly.

[1]

I. Clearanc e to service regulator vent outlet 3ft [91cm] min. J. Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance: In Canada, 6in [15cm]

for appliances ≤10,000 BTUh [3kW], 12in

[1]

[30cm] minimum for appliances >10,000 BTUh [3kW] and ≤100,000 BTUh [30kW], 36in [91cm] for appliances >100,000 BTUh [30kW]. In the USA, 6in appliances >10,000 BTUh [3kW] and ≤50,000 BTUh [15kW], 12in [30cm] for appliances >50,000 BTUh [15kW].

K. Clearance to a mechanical air supply inlet 6ft [1.8m] min.

[4]

(US

)

[2]

[15cm] for appliances ≤10,000 BTUh [3kW], 9in [23cm] for

[1]

in Canada. In USA, 3ft [91cm] above if within 10ft L. Clearance above paved sidewalk or a paved driveway located on public property 7ft [2.1m] min. M. Clearance above highest point of exit on roof 18in [45cm]. N. Clearance to perpendicular wall 24in [60cm].

(Recommended to prevent re-circulation of exhaust products. For additional requirements check local codes.)

[1,2]

[4]

(US

),24in for 6961MQRB if combustible.

[5]

[2]

[3m] horizontally.

[2]

In accordance with the current CSA B149.1, Natural Gas and Propane Code.

In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code.

Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor.

Clearance in accordance with local installation codes and the requirements of the gas supplier.

A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family dwellings and serves both dwellings.

Page 84

General Vent Installation Information

This gas appliance is approved to be vented either through the side wall or vertically through the roof. Only Kingsman Flex (ZFlex) venting kits and components specifically approved and LABELED for this stove may be used.

Kingsman Flex venting MUST be used on the MQRB4436 and MQRB6961.

Use of DuraVent- DirectVent Pro or other hard pipe Venting systems is not permitted.

Model MQRB5143 is approved for use with DuraVent- DirectVent Pro Direct Vent system (Model DV-GS Series), and AmeriVent Direct Vent Pipe System, ICC Excel Direct, Metal Fab Sure-Seal DV and Selkirk Direct Temp. Not available for MQRB6961.

DuraVent- DirectVent Pro, AmeriVent, and Selkirk Direct Temp

When using DuraVent- DirectVent Pro, AmeriVent pipe, ICC Excel Direct, Metal Fab Sure-Seal DV, or Selkirk Direct T emp a Dura-vent adapter must be used (part # Z57DFA). Follow installation instructions provided by the appropriate manufacturer for installation of pipe, and adhere to the clearance to combustibles provided in this manual. Apply a bead of Mill Pac high temp sealant to all joints of pipes, adapters and termination as recommended.

WARNING: DO NOT mix parts from different systems unless stated in the manual.

Eight Inch Hard Pipe Adapter (Z57DFA) for MQRB5143 Only

Contents: 1 ea. 8” Adapter Plate

6ea. DT Screws

1. Remove the two [2] Standoffs at the vented end of the Fireplace.

2. Apply RTV Red Silicone to the underside of the Adapter Plate around the perimeter of the screw holes.

3. Fasten Adapter Plate to the top of the unit using the supplied DT Screws.

4. Replace the Standoffs.

Flex Pipe Venting

Flex pipe is shipped in an unexpanded length. Therefore, when installing the pipe, expand it completely and then cut off the remaining length. A flex pipe can be expanded to twice their shipped length (e.g. 4ft. to 8ft).

Do not use more than 2 couplers to extend short pipes. Single sections are preferred in an installation attaching at the fireplace and termination.

Place the spring spacers provided approximately every two feet to stabilize inner flex in the center of the outer flex pipe. When forming bends place spring in bend or before and after.

ONLY VENTING COMPONENTS SPECIFICALLY APPROVED AND LABELED FOR THIS FIREPLACE MAY BE USED.

Termination

Do not locate termination where excessive snow or ice build-up may occur. Be sure to check vent termination area after snow falls and clear to prevent accidental blockage of venting system. When using snow blowers, make sure snow is not directed towards vent termination area.

Venting terminal shall not be recessed into a wall or siding.

Page 85

Use High Temperature Mill Pac Sealant

NOTE: It is critical to the proper and safe operation of this fireplace that on all connections the inner liner and the outer casing are both caulked with liberal amounts of sealant. Do not use any kind of tape or silicone other than that recommended in this manual. Mill Pac Sealant

Example

If the length of the horizontal run is 10ft [3m], and two 45 degree bends are required, then the horizontal run length must be reduced to 7ft to achieve proper venting. If 10ft of horizontal run is required in conjunction with the two 45 degree bends, then the vertical run must be increased appropriately. Please refer to Horizontal Vent Table for the relationship between horizontal and vertical runs.

IMPORTANT: Always locate the fireplace in such a way that a minimum of offsets and/or horizontal runs are required. 1/4” vertical rise is required for every 12” horizontal run.

Seal with High Temperature Mill Pac Sealant

Figure 1 - Flex pipe spring spacing guide.

Horizontal runs require support metal straps every 2ft. In an offset installation support straps should be used to stabilize pipe.

Expand inner and outer flex pipe to the point that the outer flex pipe protrudes approximately 2 to 3 inches past outer wall and the inner flex protrudes approximately 2 to 3 inches past the outer flex pipe. Attach the inner flex pipe to the termination first and secure with sealant and [4] screws. Then attach the outer flex pipe to the termination with caulking and screws. Termination may then be moved back to the outer wall and attached to home screwing into the framing. Use silicone around the termination to provide waterproof seal. If siding shield is going to be used attach this after termination has been caulked for waterproofing.

Apply a bead of Mill Pac high temp sealant to all joints and use four screws to secure each pipe at fireplace, termination and

any joint if joining any sections of pipe.

Venting Routes and Components

Since it is very important that the vent system maintain its balance between the combustion air intake and the flue gas

exhaust, certain limitations as to vent configurations apply and must be strictly adhered to. The table on the following page

showing the relationship between vertical and horizontal side wall venting will help to determine the various vent lengths.

The maximum horizontal run with the 90 degree bend at the fireplace flue outlet is 3’. The maximum horizontal run is 20ft

when the vertical run is 8ft. Note: 1/4" vertical rise is required for every 12" of horizontal run (see Horizontal Vent Table).

Two additional 90° bends (or the equivalent) are allowed in the horizontal run. The horizontal run must be reduced 36” for each

90° bend. The horizontal run must be reduced 18” for each 45° bend.

The maximum vertical run is 43ft [13.1m].

Special Note: For each 45 degree bend installed in the horizontal run, the length of the horizontal run must be

reduced by 18" [46cm]. This does not apply if the 45 degree bends are installed on the vertical part of the vent

system.

Page 86

Minimum clearance to combustibles on venting is 1” with

the following exceptions:

MQRB4436

MQRB5143

MQRB6961

Top of horizontal 2” 2” 2” Top of 90 degree elbow in an enclosure under 72” 5” with Z57WTS 5” with Z57WTS N/A Top of 90 degree elbow in an enclosure over 72” 4” 4” N/A Top of 90 degree elbow in an enclosure under 78” N/A N/A 6-1/2” with Z57WTS Top of 90 degree elbow in an enclosure over 78” N/A N/A 6-1/2” Minimum Enclosure Height (See Enclosure Heights page)

60” 60”

64” Vertical 68” Horizontal

Minimum Termination Height from bottom of Unit 37-1/2” + ¼” rise/ ft 51-1/2” + ¼” rise/ ft 56-1/2” + ¼” rise / ft

Horizontal Vent Table

To use the Horizontal Vent Table (see Table 1), determine the total vertical height of the system and the number of bends

required. Locate the value on the first column and then move across to see the corresponding maximum allo wable h orizontal

run. All Measurements are from the bottom of the appliance.

For Propane Horizontal

installations on

MQRB4436 &

MQRB5143, the

venting must be a

minimum of two feet

vertical off the flue

before going horizontal.

Table 1 - Horizontal Vent Table

MQRB4436 MQRB5143 MQRB6961

*4436MQRB

Only

The minimum vertical installation height must be adhered to.

Flex pipe venting must be fully stretched.

otal Vertical

Feet Meters Feet Meters Feet Meters Feet Meters 37-1/2" 51-1/2” 56-1/2”

5 6 7 8

9 10 11 12 13

1.3

1.4

1.2* 4* 1.2*

1.5 5 1.5 15 4.6 20 6.1

1.8 8 2.4 16 4.9 20 6.1

2.1 15 4.6 17 5.2 20 6.1

2.4 20 6.1 18 5.5 20 6.1

2.7 20 6.1 19 5.8 20 6.1

3.0 20 6.1 20 6.1 20 6.1

3.4 20 6.1 25 7.5 15 4.6

3.7 20 6.1 30 9.0 10 3.0

4.0 20 6.1

Max. Horizontal

3 .91

Total

Vertical

4.3

Max. Horizontal

43 12.2 0 0

6.1

Figure 1

NOTE: The final location of the fireplace must be such that the horizontal vent dimensions fall within those stated on the graph. The Maximum Vertical vent run is 43ft. Please refer to Clearance to Combustibles information in this manual.

A Safety Cage is required if the Horizontal Termination is accessible.

MQRB5143 / MQRB4436: See Flue Restrictor Adjustment Page for vertically vented Installations.

8ft

24” Min To Centerline

To Edge of Plate

MQRB6961: Note Clearances of Termination from vented and unvented soffit (24”) and adjacent Side wall (6”). Also see D and E on Venting page.

Page 87

MQRB5143 Venting Examples

ll horizontal runs have a minimum ¼” rise per foot.

2-1/4"

Wall Thimble and Roof Support

The Wall Thimble is used in horizontal installations to shield the combustible material from the vent pipe. T he appropriate size of thimble is required for each model. Please contact your local dealer for more information. Refer to Side Wall Venting for wall cutout information.

The Roof Support is used to secure the vertical venting as it penetrates the roof. Please note that you may only install the roof support to a rigid pipe.

Wall Thimble and Roof Support kits

11” [26.7cm] for MQRB4436 / MQRB5143 13-3/4” [34.3cm] for MQRB6961

Page 88

Installation of Side Wall Venting

Note: Wall Thimble Shield [Z57WTS] must be used in Enclosures under 72” for MQRB4436 / MQRB5143, and under 78” for MQRB6961.

3ft

5” Min. for

MQRB4436 / MQRB5143

6-1/2” Min. for

52-1/4”Min

Vertical rise over 3ft horizontal run (MQRB5143 shown).

Note that the minimum height from the bottom of fireplace to the centre of vent is 37-1/2" [95 cm] for the MQRB4436, 51-1/2" [131 cm] for the MQRB5143 and 56-1/2” [144cm] for the MQRB6961. This dimension is for installations where venting exits immediately after its

rise from the unit (i.e. zero/minimum horizontal length). In installations where there is a horizontal run simply refer to the Horizontal Vent Table to determine the vertical location of the hole cutout required.

1. In a combustible wall cut a square hole that is 11” x 11” [28cmx28cm] (inside dimension) for the MQRB4436 / MQRB5143 or 133/4" x 13-3/4" [35cmx35cm] for the MQRB6961. In a non-combustible wall, cut an 8” [20cm] diameter hole for the MQRB4436 / MQRB5143 or an 11" [28cm] diameter hole for the MQRB6961. See below for detail.

2. Refer to Clearance to Combustibles information in this manual. Select the approximate vent length for your installation. Note that

precise measurements are not needed as the flex pipe can be expanded to twice its shipped length.

3. If installing the wall thimble, center it over the square cutout hole and secure both pieces on either sides of the wall. Route the flex vent pipe through the wall thimble. Before joining pipes, apply a bead of high temperature sealant (Millpac) to the end. Then attach the inner pipe to the vent termination with sealant, and secure it with the four screws provided. At this time make sure the spacer springs are attached to the inner flex pipe. Then attach the outer pipe by the same method.

4. Mount the vent termination and seal it to wall using caulking around the thimble to weather proof. After installing the vent termination, double check to make sure the pipe extends properly through wall thimble and into the termination. Before joining pipes to the fireplace flue, apply a bead of high temperature sealant (Millpac) to the end of it. Then attach the inner flue pipe to fireplace with sealant; and secure with the four screws provided. At this time verify that the spacer springs are attached properly to the inner pipe and then attach the outer pipe by the same method.

5. Support the horizontal pipe every 2ft [61cm] with metal strap bands. Verify that the fireplace is leveled, properly positioned, and secured to the framing.

6. Support vertical pipes with metal strapping to maintain a minimum of 1" [2.5cm] or greater clearance to combustibles.

MQRB4436 / MQRB5143

37-1/2" Min -MQRB4436

51-1/2” Min -M

RB5143

56-1/2” Min

MQRB6961

Page 89

Z57ST24 / Z57ST36 Horizontal Snorkel Terminations MQRB4436 / MQRB5143

-FOR INFINITE SERIES II MODELS ONLY-

Two snorkel terminations are available for MQRB4436 / MQRB5143 If a vertical rise is necessary on the exterior side of a building:

Z57ST24 (24” Tall, 14-1/2” Center to Center) Z57ST36 (36” Tall, 26-1/2” Center to Center) Follow standard horizontal venting installation procedures. If the Snorkel Termination is to be located below grade, a

window well is recommended with adequate and proper drainage as per local codes. Leave 2” clearance below snorkel to prevent water from entering the Snorkel Termination. Do not enclose the Snorkel within a wall or other type of enclosure and do not back fill. Ensure that grade level slopes away from the building. Follow all local codes.

Maintain All Clearances, including proper rise and run.

Ensure adequate drainage.

-FOLLOW ALL LOCAL CODES-

 A safety cage (Z57STSC) is also available.

Place safety cage over snorkel and mount with [4] DT screws (supplied with safety cage).

Page 90

Venting Straight Up Through Roof

An Attic Insulation Shield must be installed where the vent passes from a lower living space into an attic space where the chimney is

Attic Insulation Shield

Fire Stop

MQRB4436 MQRB5143

MQRB6961

VERTICAL VENT FRAMING - TOP VIEW-

not enclosed. It is designed to keep insulation materials away from the chimney. When installing the Attic Insulation Shield where the chimney passes from a living space to an attic space, install the shield from below and nail in place using 1" spiral nails. A fire stop must be installed on the bottom side of the joists when passing through a ceiling or floor. If an attic insulation shield is to be used, a fire stop is not required.

Using Flex Bends

Avoid cutting joists by offsetting the flex pipe. When using 45° bends a bend support is required directly above the highest bend. When installing a bend in a joist area a minimum of 4" clearance to combustible to the top of bend must be maintained, sides and bottom of pipe, a 1" clearance to combustibles must be maintained. If running horizontal through an area a 2" minimum clearance to the top of the horizontal pipe must be maintained. Maximum vertical height of system should not exceed 43 feet. Use roof support and rigid pipe at roof level. Flex pipe is not permitted within roof support. When penetrating the roof a rigid galvanized pipe must be used. Attach flex pipe to the rigid pipe with high temperature sealant, secure with four screws assuring the flex pipe and rigid pipe are secured. Attach rigid pipe to termination with sealant and screw with 4 sheet metal screws. The Inner flex pipe must be secured with 4 screws which must penetrate both the flex pipe and inner section of termination. Vertical termination clearance is 18" [45.7cm] above the roof, measured from highest point of exit on the roof line. Support vertical pipes to maintain minimum of one inch or greater clearances to combustibles.

Roof Flashing

Ensure that you have the proper roof flashing by checking your roof pitch using a level and two rulers, or by using a roof pitch card. Slide a Roof Flashing suitable to your roof slope over the vent. Place the edge of the flashing plate that will be on the higher part of the roof slope under the shingles. Both the sides and the lower edge lay on top of the shingles.

NOTE: At the top edge of the flashing plate, lift the shingles and nail the plate to the roof deck, then cement the shingles to the plate with a suitable waterproof mastic.

Ensure that the chimney is plumb. Square up the flashing plate and nail in place to the roof deck. Use 12 nails with neoprene washers or cover the heads with a suitable waterproof mastic. Wrap the storm collar around the vent above the flashing. Secure the ends together loosely with nut and bolt supplied. Slide the collar down the vent until it comes in contact with the flashing. Tighten the bolt and seal the Storm Collar to the vent with a suitable waterproof non-combustible mastic. The flashing and storm collar should be painted to match the roof shingles. This will extend its life and improve the appearance. Clean, prime and paint with suitable painting products.

Vertical Venting in Cold Climates

In cold climate conditions where temperatures go below -10 degrees Celsius or 14 degrees Fahrenheit, we recommend that the chase be insulated and where the vent pipe enters into the attic space that the pipe be wrapped with an insulated Mylar sleeve. This will increase the temperature of the vent and help the appliance to vent properly in cold weather conditions. It is also important in vertical vented direct vent appliances that the appliance be operated daily during the winter months as this will help stop the termination from freezing up. We recommend using a thermostat [In the U.S.A. Thermostats are not permitted for Vented Gas Fireplaces (ANSI Z21.50b- Decorative)]. set at room temperature to allow the unit to cycle. For IPI models it may be necessary to set the appliance to Standing Pilot mode to maintain heat in the cavity. The purpose of this procedure is to prevent cold air from penetrating the chimney and then onto the living space. Therefore, when the internal temperature is slightly elevated the fireplace is able to freely exhaust its combustion and hence making it easier to startup.

Page 91

2” Top of Horizontal Vent

43ft

Z710VT for MQRB6961

-Restrictor-

Remove for Runs

Under 15 Feet

Clearances in horizontal venting.

Straight-through roof support configuration; b) Flex bend configuration; c) Termination mounting

Page 92

Flue Restrictor Adjustment

MQRB4436 / MQRB5143 Only –All Models

Fig.1

The Flue Restrictor is located in the top of the

Firebox in front of the Flue Opening.

For vertically vented installations it is necessary to use the Flue Restrictor. Restrictor is set fully open from factory for short horizontal and vertical runs.

To adjust the Flue Restrictor:

1. Remove the [2] DT screws in the Flue Restrictor. Also remove the [2] screws at the front of the Flue (Fig.1).

2. Rotate the Flue Restrictor 180°. (Fig.2). Place the Flue

Restrictor over the Flue & start the [4] DT screws in the screw holes.

Fig.2

Fig.3

3. For Vertical Venting 20-30 feet in height, the Flue

Restrictor should be open 1-7/8” from the back of the

Flue (Fig. 3).

4. Between 30/40 feet: Set Restrictor in conjunction with

the number of 90° elbows.

• 1 to 2 elbows 1-3/8”

• 2 to 3 elbows with offsets 1-7/8”

5. For Vertical Venting 40 feet or above in height, the Flue

Restrictor should be open 1-3/8” from the back of the

Flue (Fig. 4).

Fig.4

Page 93

58PVH-Dimensions

13"

11"

13"

10-5/8"

13"

8-1/8"

12-1/2"

1-1/2"

1/2"

10-5/8"

1-1/4"

16"

8-1/8"

11"

11-1/8"

11"

11-3/8"

Page 94

PVH58 INSTALLATION OVERVIEW

The PVH58 Horizontal Power Vent is approved for the following models only:

MQRB4436, MQRB5143, MQRB6961

Either Hard Pipe or Flex Pipe can be used, along with the appropriate adapter kit.

The Following Steps Are Required To Install The PVH58 Horizontal Power Vent:

 Install fireplace as per manual instructions (51MQ-MAN, 51MQ-MAN-II).  Choose suitable location for PVH58 Power Vent Termination. Refer to Termination Installation and

PVH58 Venting Clearances sections of this manual.

 Determine venting configuration to be used (i.e. hard pipe or flex, and routing). Install venting with appropriate adapter kits. See PVH58 Venting – Hard Pipe or Flex, and PVH58 Venting Configurations sections of this manual.

 Install PVH58 Wall Thimble if mounting in a combustible wall (PVH58 Wall Thimble Installation section).

 Install PVH58 Power Vent (PVH58 Power Vent Mounting section).  Electrical connections (PVH58 Wiring Harness Connections and Millivolt / IPI System

Connections sections).  Air Intake Adjustment & Troubleshooting (refer to these sections).

PVH58 TERMINATION INSTALLATION

Termination Clearances

It is imperative that the vent termination be located observing the minimum clearances as shown. There must not be any obstruction such as bushes, garden sheds, fences, decks or utility buildings within 24" from the front of the termination plate. Do not locate termination where excessive snow or ice build-up may occur. Be sure to check vent termination area after snow falls and clear to prevent accidental blockage of venting system. When using snow blowers, make sure snow is not directed towards vent termination area. Venting terminal shall not be recessed into a wall or siding, except for mounting flange. ALSO REFER TO PVH58 VENTING CLEARANCES SECTION.

Mounting Flange

MINIMUM CLEARANCE ABOVE A COMBUSTIBLE SURFACE IS 27”.

FOLLOW ALL LOCAL CODES

MINIMUM CLEARANCE ABOVE

GRADE OR A NON-

COMBUSTIBLE SURFACE IS 12”.

Page 95

PVH58 VENTING CLEARANCES

Note: Clearances are to the edge of terminal plate, add 5-1/2" to clearances to arrive at center line.

Note: Local Codes or Regulations may require different clearances.

A. Clearance above a veranda, porch, deck, or balcony or other combustible surface is 27”. Clearance above grade is12in [30cm]

min.

[1,2].

B. Clearance to window or door that may be opened. 12in [30cm] min. for appliances 100,000BTUh [30kW] and lower, in Canada. 9in

[23cm] for appliances 50,000 BTUh and lower, in USA.

C. Clearance to permanently closed window min. 12in [30cm] recommended to prevent condensation o n window, in Canada. 9in

[2]

[23cm] for appliances 50,000 BTUh and lower, in USA.

D. Vertical clearance to ventilated soffit located above the termination within a horizontal distance of 2ft [60cm] from the center line of

the termination. 18in [46cm] min.

[4]

E. Clearance to unventilated soffit 12in [30cm] min. F. Clearance under veranda, porch, deck or balcony 12in [30cm] min.

[3] (US[4])

G. Clearance from a perpendicular inside wall or outer corner to the edge of the vent terminal plate is 3in [7.6cm] min. H. Clearance to each side of center line extended above meter/regulator assembly 3ft [91cm] within a height 15ft [4.5m] above the

meter/regulator assembly.

I. Clearance to service regulator vent outlet 3ft [91cm] min.

[1] (US[4])

J. Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance: In Canada, 6in [15cm] for

appliances ≤10,000 BTUh [3kW], 12in USA, 6in

[2] [15cm] for appliances ≤10,000 BTUh [3kW], 9in [23cm] for appliances >10,000 BTUh [3kW] and ≤50,000 BTUh [15kW],

[1] [30cm] minimum for BTUh [30kW], 36in [91cm] for appliances >100,000 BTUh [30kW]. In the

12in [30cm] for appliances >50,000 BTUh [15kW]. K. Clearance to a mechanical air supply inlet 6ft [1.8m] min. L. Clearance above paved sidewalk or a paved driveway located on pub lic property 7ft [2.1m] min.

[1] in Canada. In USA, 3ft [91cm] above if within 10ft[2] [3m] horizontally.

[5]

M. Clearance above highest point of exit on roof 18in [45cm]. N. Clearance to perpendicular wall 24in [60cm]. (Recommended to prevent re-circulation of exhaust products. For additional

requirements check local codes.)

1. In accordance with the current CSA B149.1, Natural Gas and Propane Code.

2. In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code.

3. Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor.

4. Clearance in accordance with local installation codes and the requirements of the gas supplier.

5. A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family dwellings and serves both dwellings.

[2]

Page 96

PVH58 VENTING HARD PIPE OR FLEX

Approved For 4/6-5/8”, 5/8” Hard Pipe

The PVH-58 Power Vent is approved for use with DuraVent-DirectVent Pro Direct Vent system (Model DV-GS Series), and AmeriVent Direct Vent Pipe System, ICC Excel Direct, Metal Fab Sure-Seal DV and Selkirk Direct Temp. installation instructions provided by the appropriate manufacturer for installation of pipe, and adhere to the clearance to combustibles provided in this manual. Apply a bead of Mill Pac high temp sealant to all joints of pipes, adapters and termination as recommended.

WARNING: DO NOT mix parts from different systems unless stated in the manual.

ADAPTERS REQUIRED FOR HARD PIPE INSTALLATION

(ADAPTERS REQUIRED AT FIREPLACE)

FIREPLACE ZRB46

(4/7” Venting)

ADAPTER

KIT

REQUIRED

*NOTE: For 4 x 6-5/8” venting on ZRB46, a ZDVDIA Duravent Pipe Increaser will be required to connect to 5/8”

hard pipe section at power vent.

ZDVDKA

Duravent Fireplace

Adapter

*See Note*

MQRB4436

(5/7” Venting)

Z57DFA

Hard Pipe Adapter

MQRB5143

(5/7” Venting)

Z57DFA

Hard Pipe Adapter

MQRB6961

(7/10” Venting)

Z69DFA- Kit

Pipe Reducer 10”Lg – 8”Sm Pipe Reducer 7”Lg – 5”Sm

ZDVDKA

ZRB46 at fireplace

Z57DFA

MQRB4436, MQRB5143

*ZDVDIA

ZRB46 at termination

Z69DFA

MQRB6961

Page 97

Approved For 4/7”, 5/7” And 7/10” Kingsman Flex (Z-Flex) Pipe

Flex Pipe Venting

Kingsman Flex pipe is shipped in unexpanded length. When installing pipe expand the lengths. Pipe can be expanded to twice their lengths e.g. 4ft. to 8ft. Fully expand pipe and cut off excess.

Be sure to use approved couplers and connectors to join flex pipe.

Place the spring spaces provided approximately every two feet to stabilize inner flex in the center of the outer flex. When forming bends place spring in bend or before and after. Horizontal runs require support metal straps every 2 feet. In off set installation support straps should be used to stabilize pipe. Expand inner and outer flex pipe to the point that the inner flex protrudes approximately 2 to 3 inches past the outer flex. Attach the inner flex to the adapter first and secure with sealant and screws then attach the outer flex to the adapter with caulking and screws. Silicone around termination to waterproof.

Use Hi Temp Sealant

Apply a bead of mill pac high temp sealant to all joints and use four screws to secure each pipe at fireplace, termination and any joint if joining any sections of pipe.

ONLY VENTING COMPONENTS SPECIFICALLY APPROVED AND LABELED FOR YOUR FIREPLACE MAY BE USED.

ADAPTERS REQUIRED FOR FLEX PIPE INSTALLATION

(ADAPTERS REQUIRED AT POWER VENT*)

FIREPLACE ZRB46

(4/7” Venting)

MQRB4436

(5/7” Venting)

MQRB5143

(5/7” Venting)

MQRB6961

(7/10” Venting)

ADAPTER KIT

REQUIRED

Z47PVA

Pipe Reducers

8”Sm – 7”Sm 5”Sm – 4”Sm

Z57PVA Pipe Reducer 8”Sm – 7”Sm

ZDV5FC

Z57PVA

Pipe Reducer

8”Sm – 7”Sm

ZDV5FC

Z69PVA Pipe Reducers 10”Sm– 8”Sm

7”Sm – 5”Sm

* One 12” section of 5/8” hard pipe must be connected directly to the Power Vent before any adapters are connected.

Z47PVA

ZRB46

Z57PVA

MQRB4436, MQRB5143

Z69PVA

MQRB6961

Page 98

PVH58 VENTING CONFIGURATIONS

Refer to Air Intake Adjustment

section of this manual to adjust Air

Intake Shutter.

MAX Venting = 125ft

plus six 90° elbows

Maximum Vent Length is 125 ft plus six 90° elbows with Air Intake Shutter fully closed. Termination must not be below unit.

Maximum / Minimum Vent Lengths:

PVH-58

This power vent can be installed up to 3ft below the installed fireplace on runs less than 100ft and not more than four 90° elbows.

Minimum Vent Length is 3ft horizontal plus minimum vertical rise with Air Intake Shutter fully open.

MIN Venting= 3ft horizontal plus

minimum vertical rise with Ai

Intake Shutter fully open

MAX 3ft Below Unit

 Refer to fireplace manual for proper installation of your firepl ace.  Minimum clearance to combustibles on venting is 1” unless otherwise stated in manual.  After 30ft of venting, clearance to combustibles is 1”.

PVH58 - Minimum Vertical Rise Before First 90° Elbow

(Measured from bottom of appliance to center of vent pipe)

ZRB46 None Required MQRB4436 37-1/2" MQRB5143 51-1/2” MQRB6961 56-1/2”

Seven 90° elbows are possible if

the total horizontal is not more than

25ft and the vertical does not

exceed 15ft.

NOTE: MODELS EQUIPPPED WITH

MILLIVOLT/ STANDING PILOT

Downward vertical vent runs are NOT

NOTE: MODELS EQUIPPPED WITH

INTERMITTENT PILOT IGNITION:

Downward vertical vent runs are

permitted, however, Cold Climate Switch

(Standing Pilot Mode) must not be used.

IGNITION:

permitted.

Page 99

PVH58 WALL THIMBLE INSTALLATION

An 11 inch square opening is required. Center Wall Thimble over the 11 inch square opening and secure both pieces on either sides of the wall. Ensure that cutout is at the lower right corner, as electrical conduit must pass through this area.

Cutout At Lower

Telescopic Wall Thimble

Right Corner when looking into building.

PVH58 POWER VENT MOUNTING

Route wiring harness through wall thimble. Mount Power Vent unit onto building. Use silicone around Power Vent mounting flange to provide waterproof seal. Secure venting to Power Vent by driving screws through

All vent connections must be sealed with high temp sealant, such as Black Mill Pack.

Straps.

Apply Silicone

Vent Pipe Attachment Strap – Secure to Venting

11” x 11” Framed

Opening In Wall

Improper Installation may

cause water damage.

Use silicone sealant on Power

Vent mounting flange and

wiring harness opening.

Vent Pipe Attachment

!WARNING

Wiring Harness

12” LENGTH OF HARD PIPE MUST BE CONNECTED DIRECTLY TO POWER VENT TO PASS THROUGH WALL THIMBLE

ALL VENT CONNECTIONS MUST BE SEALED WITH HIGH TEMP SEALANT, SUCH AS BLACK MILL PACK.

Seal this area with silicone once installation is complete

If you wish to use Flex Pipe, connect adapters to end of 12” hard pipe section (Refer to Hard Pipe or Flex section)

Seal this area with silicone once installation is complete

Vent Pipe

Attachment Strap

Wiring Harness

Page 100

PVH58 Wiring Harness Connections

100

WARNING WARNING WARNING

A qualified electrician must connect electrical wiring to junction outlet for built-in installation.

Follow all codes.

Caution: Electrical installation to be done by a qualified installer. All wires must be connected and grounded in accordance with

CSA Standard C22.1- Canadian Electrical Code part 1 or with the National Electrical Code, ANSI /NFPA 70 (latest edition) and /or in accordance with local codes.

PVH58 EXTENSION HARNESS

The PVH58 comes supplied with a 20 foot wiring harness. If required, more harnesses can be ordered. These harnesses are male to female, and can be connected together.

Strain Relief: If extension harnesses are used, connect them using a junction box, as shown. This will provide strain relief and ensure that the connection does not come apart.

CONNECTION OF WIRING HARNESS AT FIREPLACE

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation and servicing.

Wiring Harness enters fireplace here (see photos below).

Extension Harness Connection

Insert Wiring Harness through specified ¾” opening in unit. Push on connector until it snaps into place.

FOLLOW EITHER MILLIVOLT OR IPI SYSTEM INSTRUCTIONS TO COMPLETE

THE INSTALLATION.

Kingsman MQRB4436N, MQRB4436LPE, MQRB5143N, MQRB5143NE, MQRB5143LP Installation Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual