Smart
GSM+SMS
GPRS+3G
M2M RTU
User Manual
Ver 2.1
S270/S271
Date Issued: 2016-12-08
All rights reserved by
www.GPRS-M2M.com
GSM 3G M2M RTU
S270 S271 GSM 3G M2M RTU User Manual Page 2 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
Table of contents
1. Brief introduction -------------------------------------------------------------------------------------------------4
2. Safety Directions ---------------------------------------------------------------------------------------------------6
3. Physical Layout ----------------------------------------------------------------------------------------------------7
4. Settings -------------------------------------------------------------------------------------------------------------10
5. SMS commands & APP-----------------------------------------------------------------------------------------23
6. Communication Protocol--------------------------------------------------------------------------------------26
7. Registers Assignment Table----------------------------------------------------------------------------------26
8. Upgrade Firmware ----------------------------------------------------------------------------------------------26
9. Warranty -----------------------------------------------------------------------------------------------------------26
Model
GSM/3G
Precision
DIN
AIN
PT100
DO
T/H
Register
Record
Port
S270
V
12bit
2 2 0 2 1 X 200
USB
S271
V
12bit
4 4 0 4 1 X 200
USB
S271-PT
V
12bit
4 0 4 4 1 X 200
USB
V
12bit
4 2 2 4 1 X 200
USB
S272
V
12bit
8 6 0 4 1 X TF Card
S273
V
12bit
8 6 0 4 1
64
TF Card
S275
V
16bit
8 6 0 4 1
64
TF Card
USB/RS232/RS48
5/RJ45
Notice
1. For 3G Version, the model should plus C or W, C stands for inbuilt module is CDMA2000. W
stands for inbuilt module is WCDMA;
2. T/H: temperature & humidity input for environment monitoring, Range: -40~80°C , 0~100%RH.
3. The standard package:
1x RTU, 1x GSM Antenna, 1x AC/DC Adaptor,1x Android APP, 1x PC Configuration Software,
1x USB cable, 1x User Manual, 1x Backup battery inside, Terminals for Connection.
4. The standard package not includes: SIMCard , Temperature+Humidity sensor AM2301.
Warning Tips:
Please Read the user manual firstly before any configurating and operating.
This handbook has been designed as a guide to the installation and operation of GSM 3G RTU S270 and S271.
Statements contained in the handbook are general guidelines only and in no way are designed to supersede the
instructions contained with other products.
We recommend that the advice of a registered electrician be sought before any Installation work commences.
King Pigeon Communication.Co.,Limited. its employees and distributors, accept no liability for any loss or damage
including consequential damage due to reliance on any material contained in this handbook.
King Pigeon Communication.Co.,Limited. its employees and distributors, accept no liability for GSM/3G Network
upgrading or SIMCard upgrading due to the technology specifications contained in this handbook.
S270 S271 GSM 3G M2M RTU User Manual Page 3 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
1. Brief Introduction
The GSM 3G M2M RTU(Remote Terminal Unit) S270/S271 inbuilt quad band GSM/GPRS module (Or
WCDMA/CDMA2000) and ARM® Cortex™ 32 Bit RISC Core. It is a multi Isolation I/O port remote terminal unit.
It is special for remote control and remote data acquisition, Base Transceiver Stations monitoring, access control,
ATM, generator monitoring, Pump station monitoring, weather satiation monitoring and other applications.
The S270/S271 GSM 3G M2M RTU is designed as a cost effective remote control system alert device. It
monitors up to 2/4 digital inputs and 2/4 solid relay outputs and 2/4 AD inputs and power status, onsite
temperature and humidity. All of the inputs and outputs are isolation. User-defined SMS is sent to pre-configure
mobile phone numbers when a pre-defined alarm condition happens. These pre-configured mobile phone
numbers can belong to technicians or engineers who are responsible in handling corresponding alarms. With
the aid of this GSM 3G M2M RTU, the alarm condition brings attention to in-charge personnel immediately.
Besides it allows those mobile phone users to trigger any relay output by using SMS. The output can be
connected with alarm indication device, such as alarm, and others.
Moreover, the GSM 3G M2M RTU can be used as a smart PLC(Programmable Logical Controller) by the
interlock function. And be used as a remote access control, the authorized users can open the gate or turn on
the machine with a free charge call at specified time.
The GSM 3G M2M RTU supports Modbus TCP, TCP/UDP protocol over GPRS/3G network.
The GSM 3G M2M RTU can be used as:
A SMS Alarm Controller. The IO activations or deactivations can be reported by SMS and optionally
confirmed by phone calls. Each input can have its own message texts and the message can be
programmed by users.
A Switch with SMS Remote Control. SMS texts for switching particular terminals on/off or pulse output
are configurable.
A Timer-Switch which can be activated automatically. It can be setup when to performs preset logic
events, e.g.: timer reports its status, timer switch on/off device or equipments automatically.
An Access Control unit. Up to 10 authorized tel. numbers can be authorized for dial to access control
and open the electricity door directly with free charge.
A PLC Automation Control system. Upton 40 programmable logic events can be preset by users. E.g.:
Each input alarm or recovery can link to one or more output actions, this is very useful when the
temperature up to appointed value, need switch on the air-conditioning immediately, or when water
overflow and need switch on the dryer, or when somebody broken into the door or windows need to start
the CCTV and Siren.
A SMS reporter. The GSM 3G M2M RTU can setup daily automatically report one or more times of its
current status to users automatically.
A Pulse Counter. The digital inputs can be used as the pulse counter, the user can setup both of interval
value activated alarm and total value activated alarm.
A Data Logger. The unit can save all of the events or acquisition data in internal memory storage, the
historical data can export to CS format via USB port or upload to server by GPRS /3G network according
to schedule, no distance limitation.
S270 S271 GSM 3G M2M RTU User Manual Page 4 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
A Wireless Data Acquisition to SCADA or HMI or Monitoring Center. The unit can acquisition variety
data(E.g.: Pressure, Level, Current, Voltage, digital input status, pulse counter, digital relay output status,
temperature value, humidity value and other) and upload to the SCADA(supervisory control and data
acquisition) or HMI or Monitoring Center by SMS/GPRS/3G, no distance limitation.
1.1 Typically Applications
Typically Application Diagram:
S270 S271 GSM 3G M2M RTU User Manual Page 5 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
Suitable Applications:
1. Security Alarm System applications; 2. Supervision and monitoring alarm systems
3. Automatic monitoring system; 4. Vending Machines;
5. Pumping Stations; 6. Buildings and Real Estate;
7. Weather Stations remote control and data logging; 8. River Monitoring and Flood Control remote control;
9. Oil and gas pipelines remote control and data logging; 10. Corrosion protection
11. Valve controls; 12. Wellheads;
13. Energy saving,street lights control system; 14. Tanks, levels, temperatures,water leakage applications;
15. Transformer stations; 16. Unmanned machine rooms;
17. Control room application; 18. PLC and Automation System, M2M;
19. GSM Access Control System, GSM Gate Opener, etc.
System Schematic Diagram
A: I/O port connections;
B: Through GPRS or 3G to HMI, OMC, the TCP/IP protocol is KingPigeon Definition Protocol.
C: Through GPRS or 3G to SCADA,HMI, DCS, OPC Server, Under this condition, the RTU performs Modbus
Slave. And the TCP/IP Protocol is Modbus TCP.
D: Using SMS to control the RTU, or receive SMS alarm alert, or through voice communication to open the door
or receive alarm calling.
1.2 Mainly Features
1) ARM® Cortex™-M4 32 Bit RISC Core, RTOS system;
2) Quadband 850/900/1800/1900Mhz GSM GPRS Module inside, WCDMA/CDMA2000 Modules are optional.
3) Widely Rated voltage range, 9~36VDC, Inbuilt large capacity rechargeable backup battery;
4) Large internal memory to save 200 historical records, USB port for configuration and upgrade firmware;
5) 2/4 analog inputs, 12bits resolution, supports 0-5V, 0-20mA, 4-20mA output transducers;
6) 2/4 solid relay outputs, rated capacity is 5A/30VDC,5A/250VAC;
7) 2/4 digital inputs, compatible to dry contact or wet contact inputs. Logic level: 0~0. 5V or short circuit treated
as close, +3~30V or open circuits treated as open. One of the input can be used as counter, sampling
frequency is 1Khz;
8) 1 temperature & humidity sensor input for monitoring onsite environment, the sensor model is AM2301,
Measures temperatures from -40-80°C,0.5°C accuracy, Relative Humidity from 0-99RH%, accuracy is 3%;
9) All of the I/O ports with electromagnetic isolation protection;
10) 2 IP data centers, supports Modbus TCP,TCP/IP protocol over GPRS/3G network;
11) Automatically resend the data while GPRS/3G communication interrupt or failure, GPRS/3G failure will alert
S270 S271 GSM 3G M2M RTU User Manual Page 6 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
by SMS text to users.
12) Supports remotely restart the RTU, and configure& operate it by SMS commands remotely;
13) Supports over voltage protection and phase-reversal protection, provide DC power sources for external
transducers or sensors to save wiring cost.
14) 10 SMS Alert and auto dial numbers for receiving alarm message, can program to receive specified alarm
message. The authorized numbers also can dial to open the door or turn on/off machine with a free charge
call at the specified time.
1.3 Specifications
Item
Reference Scope
DC Power supply
Standard adapter: DC 12V/1.5A Range 9-36VDC
Power consumption
Standby:12V/70mA; Working Max.: 12V/300mA
GSM/3G Frequency
850/900/1800/1900Mhz/3G (WCDMA)
Transmit power
Class 4 (2W) at EGSM 900 and EGSM 850
Class 1 (1W) at GSM 1800 and GSM 1900
GPRS connectivity
GPRS multi-slot class 10
GPRS Data Transmission
GPRS data downlink transfer: max. 85.6 kbps
GPRS data uplink transfer: max. 42.8 kbps
Coding scheme: CS-1, CS-2, CS-3 and CS-4
TCP/IP stack
TCP,UDP
SIM interface
Supporting 3V SIM Card
External antenna
SMA Antenna interface, 50 Ohm
Alarm Phone Numbers
10 telephone numbers for SMS Alert and Dial while alarm.
Serial Interfaces
1 USB Port with ±15KV ESD Protection.
Protocols
SMS, GPRS UDP,TCP, Modbus TCP
Digital Inputs
2/4 Digital inputs, dry contact or wet contact. Logic level: 0~0. 5V or short
circuit treated as close, +3~30V or open circuits treated as open. One of the
input can be used as counter, sampling frequency is 1Khz;
Analog Inputs
2/4 analog inputs, 12bits resolution, supports 0-5V, 0-20mA, 4-20mA
output transducers;
Temp.&Hum Inputs
AM2301, Range: Temperature: -40°C to +80°C, Humidity: 0~100%RH;
Relay Outputs
2/4 Solid Relay outputs, Rated Capacity: 5A/30VDC,5A/250VAC
Power Outputs
1 Port, for external device (Transducers or detectors or sensors).
Memory Capacity
Internal Memory inside, can save 200 historical events.
Backup Battery
3.7V 1200mAH, standby 8-16hours.
Temperature range
-10-+70 °C
I/O Isolation
Electromagnetic
Power input/Out
Over voltage protection and phase-reversal protection
Humidity range
Relative humidity 95% (condensation free)
Exterior dimension
168mm*113mm*26mm(external Maximum size)
Net Weight
1000 g
2.Safety Directions
Safe Startup
Do not use unit when using GSM/3G equipment is prohibited or might bring disturbance or
danger.
Interference
All wireless equipment might interfere network signals of unit and influence its performance.
Avoid Use at Gas Station
Do not use unit at a gas station. Power off RTU when it near fuels or chemicals.
S270 S271 GSM 3G M2M RTU User Manual Page 7 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
Power it off near Blasting Places
Please follow relevant restrictive regulations. Avoid using the device in blasting places.
Reasonable Use
Please install the product at suitable places as described in the product documentation. Avoid
signal shielded by covering the mainframe.
Use Qualified Maintenance Service
Maintenance can be carried out only by qualified maintainer.
3. Physical Layout
LED Indicator Definition
S270 S271 GSM 3G M2M RTU User Manual Page 8 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
Power
RTU status indicator, LED ON when switched RTU on. OFF when switched RTU off.
Alarm
Alarm Indicator, alarm will ON and flick quickly. Normally is OFF;
Arm
Arm/Disarmed Indicator, Arm is ON, disarmed is OFF.
Run
RTU running status indicator, ON or OFF stands for RTU halted, flicks slowly
stands for RTU running.
GSM/3G module indicator. Flicks quickly(less than 1second per time) stands for
searching GSM/3G Network or no SIMCard inside or SIMCard connection is not
good or cannot register to GSM/3G network successful. Flicks slowly (about
1sencond per time)stands for GSM/GPRS/3G stands for registered successful and
GSM/3G Module standby.
Power Connector Definition
DC IN+
External DC Power input port, Connect to 1.5A@9~36V DC power, positive
electrode.
DC IN-
External DC Power Input port, contact to negative electrode
DC Out+
Power source output port, positive electrode. Provides power from RTU to
external transducers or sensors or detectors. The output voltage and current is
the same as the power from DC IN inputs.
DC Out -
Power source output port, Negative electrode.
DIP Switch Definition
For S270, 2 and 3 switches are useless.
SET/RUN
For setting the RTU Mode is in Configuration Mode or Run mode.
Switch it to upside is Set Mode, under this mode, the user can use PC
Configurator via USB cable to configure the RTU Parameters or Read Parameter
settings.
Switch it to Downside is Run Mode, under this mode, the RTU is in Running
mode.
0/V/mA
The 1st channel of analog input type switch. If not use this channel then no matter
is upside or downside.
Switch it to upside stands for the 1st analog input should connect to 0~5V voltage
output transducer.
Switch it to Downside stands for the 1st analog input should connect to 0~20mA or
4~20mA current output transducer.
1/V/mA~3/V/mA
The 2nd ~4th channel of analog input type switch. If not use this channel then no
matter is upside or downside.
Switch it to upside stands for the related analog input should connect to 0~5V
voltage output transducer.
Switch it to Downside stands for the related analog input should connect to
0~20mA or 4~20mA current output transducer.
Analog Input Definition
Analog inputs, 12bits resolution, supports 0-5V, 0-20mA, 4-20mA output transducers, please refer to
abovementioned DIP Switch Definition to connect the correct transducers.
For S270, 2+/2- and 3+/3- ports are useless.
0+/0-
The 1st Channel Analog input. + stands for positive electrode, - stands for
negative electrode.
S270 S271 GSM 3G M2M RTU User Manual Page 9 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
1+/1- ~ 3+/3-
The 2nd ~4th Channel Analog input. + stands for positive electrode, - stands for
negative electrode.
Digital Input Definition
Dry contact or wet contact. Logic level: 0~0. 5V or short circuit treated as close, +3~30V or open circuits
treated as open. One of the input can be used as counter, sampling frequency is 1Khz.
For S270, 2/3 and GND ports are useless.
0
The 1st digital input, positive electrode.
1~3
The 2nd ~ 4th digital input, positive electrode.
GND
GND for digital inputs, negative electrode.
ATN Port Connector Definition
ATN
GSM/3G Antenna connector, 50Ohm, SMA female.
USB Port Connector Definition
USB
USB port, for configuration and upgrading firmware and exporting historical data;
Temperature&Humidity Sensor Port Definitions
T/H
Temperature & Humidity sensor AM2301 inputs. Measurement Range:
Temperature: -40°C to +80°C, Humidity: 0~100%RH.
Digital Solid Relay Output Connector Definition
Solid Relay inside for outputs, Rated Capacity: 5A/30VDC,5A/250VAC.
For S270, 2+/2- and /3+/3- ports are useless.
0+/0-
The 1st Channel Solid Relay Output. + stands for positive electrode, - stands for
negative electrode.
1+/1- ~ 3+/3-
The 2nd ~ 4th Channel Solid Relay Output. + stands for positive electrode, - stands
for negative electrode.
S270 S271 GSM 3G M2M RTU User Manual Page 10 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
Backside Switch&Button Definition
SIMCard Holder
For SIMCard Installation, only supports 3V SIMCard, not supports 5V
Simcard.
Power Switch
For switch ON or OFF the RTU.
Upgrade Firmware Switch
For upgrade firmware purpose only. Only when upgrade new firmware
version will use it. Please keep it at Work Side all the time.
Reserved Button
Reserved Button, Useless.
4. Setting
The GSM 3G M2M RTU is user-friendly design. The user can setup it or export historic data by the PC
Configurator through USB cable, and upgrade firmware by USB port. The GSM 3G M2M RTU also can be
configured some basically parameters by SMS Commands or Android APP and IOS APP, please refer to
Chapter 5.
Tips!
1) Please insert the SIMCard firstly, and install the GSM Antenna, please power on to check the LEDs status
according to abovementioned LED Definitions, then switch off it before you program it by PC Configurator.
2) The PC Configurator in the CD, please click it to run it. Also can download from www.GPRS-M2M.com under
S270/271 page directly.
3) The PC Configurator cannot run until it contacted to the GSM 3G M2M RTU successful.
Below is the steps to setup the parameters by PC Configurator, please follow it step by step.
Start to Configure the RTU :
Step1: Install the GSM 3G M2M RTU Configurator
The GSM 3G M2M RTU Configurator in the CD or download from www.GPRS-M2M.com, then installs it on
the computer.
Step2: Connection
Please insert the SIMCard, and install the GSM/3G Antenna.
Step3: Switch the DIP Switch to Setup Mode. (Before Power On the RTU)
Switch it to upside is Set Mode, under this mode, the user can use PC Configurator via USB cable to
configure the RTU Parameters or Read Parameter settings.
Notice:
Please Switch it to Downside after you finished the configurations. Otherwise, the RTU cannot work properly. The Downside
is Run Mode, under this mode, the RTU is in Running mode.
Step4: Connect the RTU to the PC by USB Cable. And connect the external DC Power to DC Power Ports,
see below:
S270 S271 GSM 3G M2M RTU User Manual Page 11 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
Step5: Power On the RTU by the Backup side Power Switch. See below:
Notice:
The Upgrade Firmware Switch must at Work Side. See below picture.
Step6: Install USB Drvier
Please Contact the unit to the PC by USB Cable, and then install the USB Driver to the computer from the
CD firstly. When successful, it can be found out at the device manager of the XP or Windows 7 or Win10,
please see the below photo. Also, the driver for different OS can be downloaded from Silicon Laboratories,
Inc. http://www.silabs.com , the model is CP210x.
Step7: Run the GSM 3G M2M RTU Configurator
Open the Root of PC Configurator, there are 3 files, the last 2 files must be in the same root, the
WindowsInstaller3.1 is not necessary, it is a Service Pack file for windows OS. Click the Setup.exe to
install the PC Configurator.
Tips: In some computer, it required download .net framework 4.0 while installation, then please click “Yes” to go to
Microsoft website to download this service pack.
After installation successful, on the desktop please click to run it. Enter the password, default
is 1234. Then you can enter the configuration page as below:
S270 S271 GSM 3G M2M RTU User Manual Page 12 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
Notice:
If display the below windows, then means the RTU connect to the PC failure. The reasons are below:
1) USB Driver installation failure;
2) USB Cable connection is disconnected;
3) The DIP Switch in RUN mode, not in SET mode;
4) The Upgrade Firmware Switch at Load side, not at Work side.
5) Power Switch switched off or DC Power Connection is disconnected.
6) Must reboot the RTU after change the dip switch or Load switch.
Step8: Configuration Parameters
After above-mentioned operations, it is possible to program the parameters of the RTU. The details please
see below instructions.
Basic Settings
Save Settings: Click it to save all of the PC Configurator parameters to the RTU;
Load Profile: Click it to load additional Profile to the PC Configurator;
Export Profile: Click it to save the present configuration parameters as a profile for next RTU
configurating or backup the parameter settings.
Tips: The Load Profile and Export Profile is very useful while you need to program bulks of RTU with similar parameters.
After programmed the first unit then you can export profile to save it, for the second RTU then you can load profile directly to
save you time.
Default: Click it to recovery the parameters to factory defaults.
Parameter Settings
Modify Password: this is for modifying the RTU’s Password, default is 1234.
Synchronous machine time: this is to setup the RTU’s time for daily report or other timers. After click
, the RTU will be synchronous the same time as the PC.
: Click it to read out the RTU’s present page parameters to PC Configurator.
: Click it to download the present page parameters from PC Configurator to RTU.
S270 S271 GSM 3G M2M RTU User Manual Page 13 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
Device ID: non-necessary. This is mainly for monitoring center to identify the RTU, if the application no
needs to identify the RTU, and then no need to fill any thing in it.
Device Description: This is the description of the RTU, e.g.: installation address, usage instructions and
so on.
Add Timestamp to Alarm SMS: Tick it stands for while alarm occurrence, the Alarm SMS will include the
RTU’S current time information at the SMS Content.
Arm automatically when Power On: Tick it stands for once the RTU powered up, the RTU will enter into
Arm Mode automatically.
Auto Arm after Disarmed: Fill the timeout to enter into Armed Mode automatically after disarmed
operation. This is usefully for security protection applications.
Tips:
Arm: Under this mode, any alarm occurrence will send SMS and dial the authorized numbers immediately. And execute the
programmed I/O outputs.
Disarmed: Under this mode, alarm occurrence will not send SMS & dial the authorized numbers.
Timer Reporting SMS Content Settings: Tick the related items to add its value/status to the Timer report
SMS contents.
Alarm SMS Content Settings: Ticks the related items to add its value/status to the Alarm SMS Contents.
Number Settings
This is to setup the Authorized User Telephone Numbers to receive the Alarm SMS or dial. Tick it stands
for while the related event alarm occurrence will send SMS to this number.
S270 S271 GSM 3G M2M RTU User Manual Page 14 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
Alarm No.: Set the alarm receiver numbers, please includes the country code, e.g. in China is 0086, input
008613570810254, if cannot received the SMS or dial, then try to set as +8613570810254, but
cannot be 8613570810254. Also, some GSM/3G Operators not required input country code, so
please remove country code, e.g. in China is 0086, and China Mobile not required country code,
so can set as 13570810254.
Power On: Tick it stands for while the RTU powered up, will automatically send a “RTU Power On” SMS to
this number.
Timer Report: Tick it stands for Timer report SMS will send to this number.
Arm/Disarm: Tick it stands for Arm or Disarm the RTU, will send SMS to this number.
Low Signal: Tick it stands for while GSM or 3G Network signal strength lower than 14 will send SMS to
this number.
Power Lost: Tick it stands for while external DC Power loss will send SMS to this number.
Power Recovery: Tick it stands for while external DC Power recovery will send SMS to this number.
GPRS Failure: Tick it stands for while GPRS connection re-try 3 times and still failure will send SMS to
this number.
Relay Switch: Tick it stands of while the Digital Solid Relay Output action will send SMS to this number.
Digital Solid Relay Output (Dout) Settings
This page is to setup the Output parameters and definite the output usages. The outputs will be used in the
Interlock Page for programmable logic events.
S270 S271 GSM 3G M2M RTU User Manual Page 15 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
Output Type: Default is NO output type. The user can choose the Output Type for the relay outputs,
includes Open Door, Switch ON/OFF, Siren and Video-interlock.
1) Open Door: Only the first Channel(DO0) can be setup as Open Door, use it for electric
lock. If setup as Open Door, then the authorized number calls in RTU, can open the
electric Lock directly or output a pulse signal and disarmed the RTU directly. See Access
Control page about the authorized number. (If close time set as 0, when call in, the relay
will keep closed.)
2) Switch ON/OFF: For switch on/off device.
3) Siren: this is for output pulse signal for siren sounds, If setup as Siren, then while the
RTU alarm and ticked the Siren function in AIN or DIN trigger pages, then this channel
will execute the setting parameters.
Channel Name: to setup the Output Channel name, e.g.: Pump or Motor and so on, in order to identify it in
SMS Contents.
Close Time: Stands for the relay close and last time.
Repeat Times: Stands for how many times does this relay should to repeat.
Interval Time: Stands for interval how many seconds then the relay repeat the action again.
ON/OFF SMS: Tick it stands for while the Recovery action, will send SMS to the authorized numbers;
Alarm Verify Time: Stands for when the Relay Close or Open last time less than this value, will not send
SMS to the authorized numbers, this is to avoid sending too many useless SMS.
Open Description: Stands for when the Relay Open, send what SMS to the authorized numbers;
Close Description: Stands for when the Relay Close, send what SMS to the authorized numbers.
Access Control Settings
This page is for setting which authorized number at what time can dial to the RTU and let the first channel
(DO0) output a pulse output.
Only when the output types of the first channel (DO0) setup as Open Door can dial to control it.
It is very useful for serviceman dial to open the electric lock door and disarmed at specified time of the
Room. Also this function can be used as authorized number dial in the RTU to output a pulse output or
always close then call again open the relay at specified time. In this condition, please setup the output type
of DO0 as Open Door, and setup other parameters correctly, and remember to setup the Auto Arm after
S270 S271 GSM 3G M2M RTU User Manual Page 16 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
Disarmed time as 0 to keep the RTU in Armed Mode if required.
Tick the box ahead the User No. stands for enable the first Authorized number can dial in to let the first
channel (DO0) output a pulse output.
Start Time: Stands for from what time this authorized number can dial in to control it.
End Time: Stands for till what time this authorized number cannot dial in to control it.
Always: Stands for this authorized number can dial in to control it all the time.
DIN Trigger Settings
This page is for setting the digital input alarm conditions and usages. The Digital input can be used as
Armed/Disarmed Button, and also can be used as pulse counter, sampling frequency is 1Khz. and
contact both of Wet-Contact and Dry Contact types digital detectors. If the input is wet contact then the
logic level: 0~0. 5V or short circuit treated as close, +3~30V or open circuits treated as open.
Input Type: The user can choose the input type for related channel. Includes: Counter, Arm/Disarm, NC,
S270 S271 GSM 3G M2M RTU User Manual Page 17 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
NO, Change and Disabled.
1) Disabled: Not use this channel.
2) Arm/Disarm: Only the Second Channel (DIN1) can be used as Arm/Disarm Switch. For
connecting a pulse output type switch to Arm or Disarmed the RTU.
3) NC: For connecting Normal close type detector, open will alarm.
4) NO: For connecting normal open type detector, close will alarm.
5) Change: For connecting normal open or normal close type detector, once the status
changed, will be treated as alarm.(This function was reserved in this version)
6) Counter: Only the first channel (DIN0) can be used as counter. It can be used for pulse
counter usage. Need to tick up the Pulse Counter box to setup initial value and interval
alarm value and total alarm value. E.g.: contact a PIR sensor to count how many people
pass through the ATM machine and so on.
Channel Name: to setup the input channel name, e.g.: Pump or Motor and so on, in order to identify it in
SMS Contents.
Current Status: Stands for input’s current status.
Recovery Alarm: Tick it stands for when the digital input recovery, will send SMS to the authorized
numbers.
Alarm Verify Time: Stands for when the digital input Close or Open last time more than this value, will be
treated as a true alarm, if less than this value, then will not alarm.
Siren: Tick it stands for while this digital input triggering, the DO that output type was setup as Siren will
execute its output parameters.
24Hr: Tick it stands for no matter the RTU is in Arm or Disarmed mode, this digital input triggered will
alarm.
Repeat Times: Stands for how many times does the RTU should repeat to send SMS to authorized
numbers.
Interval Time: Stands for interval how many seconds then resend the alarm SMS again.
DIN/AIN Alarm Settings
This page is for setup while DIN/AIN alarm, send SMS & Dial to which authorized numbers. Tick it stands
for enable to send SMS or dial the related authorized number, see below page is for DIN settings, the AIN
Alarm Settings is the same:
S270 S271 GSM 3G M2M RTU User Manual Page 18 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
AIN Trigger Settings
This page is to setup the analog input alarm conditions and analog input types.
Input Type: Default is AIN0 and AIN3 is 4~20mA, AIN1 and AIN2 is 0~5V. The user can choose the input
type for related channel. Includes: Disable, 0~5V, 0~20mA, 4~20mA.
1) Disabled: Not use this channel.
2) 0~5V: For connecting transducers that output voltage 0~5V. Please remember to switch
the related channel DIP switch to V side, see DIP Switch Definitions.
3) 0~20mA: For connecting transducers that output current 0~20mA, Please remember to
switch the related channel DIP switch to A side, see DIP Switch Definitions.
4) 4~20mA: For connecting For connecting transducers that output current 0~20mA,
Please remember to switch the related channel DIP switch to A side, see DIP Switch
Definitions.
5) Temperature and Humidity: Default is Enable. Only accept AMS230x series sensor, the
temperature maximum is 80, minimum is -40, and Humidity maximum is 100, minimum is
0, cannot change them.
Channel Name: to setup the input channel name, e.g.: Voltage or Current and so on, in order to identify it
in SMS Contents.
Maximum: The transducer’s maximum measure range. E.g.:100 Celsius degree. Usually it can be found
out at the transducer’s specification.
Minimum: The transducer’s minimum measure range. E.g : -50 Celsius degree. Usually it can be found
out at the transducer’s specification.
Current Value: Stands for input’s current value of the transducers.
Threshold High: The higher value need to alarm, like 50Celsius degree;
Threshold Low: The low value need to alarm, like -50Celsius degree;
Recovery Alarm: Tick it stands for when the analog input recovery, will send SMS to the authorized
numbers.
Alarm Verify Time: Stands for when the analog input exceed the threshold value and last time more than
this value, will be treated as a true alarm, if less than this value, then will not alarm.
Siren: Tick it stands for while this input triggering, the DO that output type was setup as Siren will execute
the its output parameters.
24Hr: Tick it stands for no matter the RTU is in Arm or Disarmed mode, this input triggered will alarm.
Repeat Times: Stands for how many times does the RTU should repeat to send SMS to authorized
numbers.
Interval Time: Stands for interval how many seconds then resend the alarm SMS again.
S270 S271 GSM 3G M2M RTU User Manual Page 19 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
Timer Setting—Daily Timer
This page is for setup daily timer, it is useful for scheduling when to execute what action automatically.
Total can program 10 scheduling events. Tick it stands for enable this timer event:
Weekly+Hour+Minute: Stands for what day and at what time does the RTU should execute the action.
Action: Stands for what action does the RTU should to execute at the specified time.
E.g.: as abovementioned,
Every Sunday 06:00, RTU automatically Reboot.
Every day 00:00, RTU upload data by GPRS to server.
Every day 18:00, RTU armed automatically.
Every Monday 08:00, RTU automatically send SMS reports to authorized numbers.
Tips:
Action: If the action is for DOUT (relay),then the relay working time, interval&repeat time is depend on the DOUT
parameter. So, if want to use the DOUT to working periodically, then just setting in here.
Timer Setting—Periodical Timer
This page is for setup periodical timer, it is useful for scheduling when to execute what action automatically
and repeat this action according to the interval time. Total can program 10 scheduling events. Tick it stands
for enable this timer event.
S270 S271 GSM 3G M2M RTU User Manual Page 20 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
Weekly+Hour+Minute: Stands for what day and at what time does the RTU should start to execute the
action and interval how many seconds then repeat to execute the action.
Interval: Stands for interval how many seconds does the RTU should repeat to execute the action. If setup
it as 0, then this event will not be repeated.
Action: Stands for what action does the RTU should to execute at the specified time.
E.g.: as abovementioned,
From the coming Sunday 07:01 start to save historical data, and executes this action every 50 seconds.
Interlock Settings
This page is for setup if what happen, then what action does the RTU should execute, it is a programmable
logic events. Total can program up to 32 logic events for automatically control purposes.
S270 S271 GSM 3G M2M RTU User Manual Page 21 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
Event: Stands for if this occurrence.
Action: Stands for then what action does the RTU should execute.
GPRS &Server Parameter Settings
This Page is for setup the GPRS online parameters, GPRS Transport data protocol and Server information.
Only when you have Server or need to use GPRS to transmit data then need to setup these parameters.
The GPRS Protocol details please refer to <S27x GSM 3G M2M RTU GPRS/3G Protocol Instruction>.
Mode: To choose which type of Server will be used, includes IP Address Server and DNS Server. If
setup Use DNS as Server, then the RTU only supports this DNS as Server, if setup IP
Connection type, then stands for using IP Address as server, and the Secondary IP Server also
can be used.
Primary IP/Domain Name: Stands for primary Server IP address or DNS.
Protocol: Stands for the GPRS transmission using TCP or UDP protocol;
Port: Stands for the server’s port.
Secondary IP: Stands for secondary Server IP address;
Enable GPRS Connection: Tick it stands for enable GPRS communication.
Definition Protocol over GPRS: Tick it stands for the protocol via GPRS is KingPigeon RTU protocol.
Modbus TCP Protocol over GPRS: Tick it stands for the protocol via GPRS is Modbus TCP protocol.
Heartbeat Interval: GPRS keep online heartbeat interval time.
APN: GPRS Access Point Name, provided by GSM/3G Operator.
User Name: GPRS User Name, provided by GSM/3G Operator.
Password: GPRS Password, provided by GSM/3G Operator.
Tips:
1) If setup as IP Connection mode, the RTU will upload data to the primary IP firstly, if failure will try to transmit data to the
secondary IP server. If the secondary IP server still failure, will try to connect the Primary IP, total 3 times.
2) The RTU only supports one of the IP Address and DNS as Server. Cannot use both of them at the same time.
Historical Record
S270 S271 GSM 3G M2M RTU User Manual Page 22 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
This page is for manage and read out the historical record from the RTU, and can save as CS format for
other purpose usage.
For historical record, the RTU total can save 200 records. Once it full, will automatically remove the earlier
100 records for new records.
The records only include alarm events, not includes power loss events, timer events.
Start to Work:
Step1: In order to save you time to program it, please click Export Profile to save these configurations as a
profile.
Step2: Exit the Configuration, and Switch OFF the RTU.
Step3: This Step is for you first time to use this RTU, or you’re not sure if the configurations are save
successful. Run the PC Configurator, and Switch ON the RTU again, enter password and try to read
out the previous settings. If can read out all of the settings, then stands for you previous settings are
successful.
Step4: Switch OFF the RTU, and remove the USB Cable, then please remember switch the 1st DIP Switch
to RUN mode. See below picture.
Step5: Switch ON the RTU, the RTU will make a long beep “DI~” for 10 seconds. If hasn’t heard the Di
sounds then means somewhere with mistake settings. Please refer to above-mentioned steps to
check it carefully. And reference to the LED Definitions to check if it enters running.
5. SMS commands & APP (Cannot Setting the Timer&Interlock).
The user can send SMS commands to setup or operate the GSM 3G M2M RTU, also can use the APP to
control it easier. The APP is under SMS communication, but their makes the program and operation easier
than edit SMS every time.
The Android APP download link:
https://play.google.com/store/apps/details?id=com.jinge.gsmseniorhelper_s275
The IOS APP download link:
https://itunes.apple.com/us/app/gsm-3g-m2m-rtu/id1095288504?l=zh&ls=1&mt=8
Or use Android smart phone/Iphone to scan the QR Bar code:
Or search it at Google Play/APP Store by name: S27x GSM 3G M2M RTU Controller
S270 S271 GSM 3G M2M RTU User Manual Page 23 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
The SMS commands will be used for remote control the RTU are below:
1) Commands error return SMS
Event
Return SMS Content
Any incorrect Command
SMS Format Error, Please check Caps Lock in Command!
2) External DC Status
Event
Return SMS Content
External DC goes off
External DC Power Goes OFF
External DC Power Goes ON
External DC Power Goes ON
3) Modify Password, 4digits, default is 1234
SMS Command
Return SMS Content
Old Password＋P＋New Password
This is the New Password, please remember it carefully.
4) Arm/Disarm SMS Command
SMS Command
Return SMS Content
Arm
password+AA
Armed
Disarm
password+BB
Disarmed
5) Set RTU time, format is 2015-05-22 15:20:30W01, the W01 stands for Monday, W07 stands for Sunday.
SMS Command
Return SMS Content
password+DxxxxxxxTxxxxxWxx
xxxx(Y)XX(M)XX(D)xx(H)X(M)xx(W)
6) Inquiry Current Status SMS Command
SMS Command
Return SMS Content
password+EE
Armed/Disarmed
Model:
Version:
IMEI:
GSM Signal Value:
S270 S271 GSM 3G M2M RTU User Manual Page 24 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
External DC Power Goes OFF/ON
7) Setup 10 User number(Alarm Number&Access Control Number), max 21digits. ( Return 0~4 or 5~9
separately while setting.)
SMS Command
Return SMS Content
Setup
password＋A＋series number+T+tel number
Notice:
Series number = 0~9
Tel1: --Tel2: --Tel3: 13570810254
Tel4: --Tel5: ---
Inquiry
password+A
Return all numbers
Delete
password+A+series number
Return 0~4 or 5~9 numbers.
8) Authority User Number to access control: authorized number can dial to disarm and open the door.
SMS Command
Return SMS Content
Setup
Specified access control time:
password＋B＋series number+S+start time+E+endtime
Always can access control:
password＋B＋series number+P
Notice:
Time format is 201505231230, stands for year, month, date, hour, minute.
Tel1: --Tel2: --Tel3: 13570810254
Tel4: --Tel5: --Inquiry
password+B
Return all authorized user numbers
Delete
password+B+series number
Return all authorized user numbers
9) Setup Daily Report time
SMS Command
Return SMS Content
Setup
password+DR+series number+T+time
Notice:
Series number =0~9, e.g.: 1234DR1T12:30
Daily SMS Report at: xx:xx
Inquiry
password+DR
Delete
password+DRDEL
10) Setup DIN Name(For recovery alert then the SMS will plus “Recovery”)
SMS Command
Return SMS Content
Set DIN Name
password+DIN+channel number+T+ DIN Name
Notice: channel number= 0~3, DIN Name max 40 characters;
E.g.: 1234DIN0TDoor alarm
DINx:
Inquiry DIN Name
password+DIN+series number<nnnn>
Notice: nnnn stands for channel number
Delete DIN Name
password+DIN+series number+DEL
Inquiry Status
password+DINE
DIN1:Open/Close
DIN2: Open/Close
-----
11) Setup AIN Name(For recovery alert then the SMS will plus “Recovery”)
SMS Command
Return SMS Content
Set AIN Name
password+AIN+channel number+T+AIN Name
Notice: channel number= 0~3, AIN Name max 40 characters;
E.g.: 1234AIN0TDoor alarm
AINx:xxxx
Inquiry AIN Name
password+AIN+ channel number<nnnn>
Delete AIN Name
password+AIN+ channel number+DEL
S270 S271 GSM 3G M2M RTU User Manual Page 25 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
Set Threshold
password+AINR+channel number+Lxxx+Hxxx
AINx: Low:xxx,High:xxx.
Inquiry Threshold
password+AINR+ channel number<nnnn>
AINx: Low:xxx, High:xxx.
AINy: Low:xxx, High:xxx.
Delete Threshold
password+AINR+ channel number+DEL
Set AIN measurement
range
password+AINM+ channel number+Lxxx+Hxxx
AINx: Min:xxx,Max:xxx
Inquiry measurement
range
password+AINM+ channel number<nnnn>
AINx: Min:xxx, Max:xxx.
AINy: Min:xxx, Max:xxx.
Delete measurement
range
password+AINM+channel number+DEL
Inquiry AIN Current
Value
password+AINE+channel number<nnnn>
AINx：xxxx ,+【Normal/Higher/Lower】
Inquiry All AIN Current
Value
password+AINE
AIN0：xxxx ,+【Normal/Higher/Lower】
AIN1：xxxx ,+【Normal/Higher/Lower】
----
12) SMS Control Digital Output
SMS Command
Return SMS Content
Set DO Name
password+DO+channel number+T
DOx:xxxx
Inquiry DO Name
password+DO+ channel number<nnnn>
Delete DO Name
password+DO+ channel number+DEL
Switch ON(Close)
password+DOC+ channel number<nnnn>
[The relay working time is always closed]
DOx: ON
DOy:ON
Switch OFF(Open)
password+DOO+ channel number<nnnn>
DOx: OFF
DOy:OFF
Switch ON(Close)
numbers of relay
password+DOLC+ channel number<nnnn>
[The relay working time is depend on the setting in DOUT
parameter]
DO1: ON
DO2: ON
DO3: ON
DO4: ON
Inquiry DO Current
Status
password+DOE+ channel number<nnnn>
DOx: ON/OFF
DOy:ON/OFF
Inquiry all DO Current
Status
password+DOE
DO1: ON/OFF
DO2:ON/OFF
---
Set Pulse Output time
password+DOT+xxx (3 digital, unit is seconds)
Pulse Output Time:xxxS
Inquiry pulse output
time
password+DOT
Pulse Output Time:xxxS
Pulse Ouput
password+DOP+channel number<nnnn>
No SMS Return
13) SMS Command for Current Counter
Remark
SMS Command
Return SMS Content
Clear the counter to start value
password+DIN0CLR
Clear OK
Inquiry current counter
password+PR
Current Counter:xxxxxx
14) Delete all the History Data
SMS Command
Return SMS Content
password+ HISDEL
Delete Successfully
S270 S271 GSM 3G M2M RTU User Manual Page 26 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
15) Set Server Parameter(Can not setup DNS by SMS)
SMS Command
Return SMS Content
Set Server IP
password+IP+ IPaddress+P+Com port
Server:
Port:
Inquiry
password+IP
Delete
password+IPDEL
16) Set GPRS APN/USER NAME/PASSWORD
SMS Command
Return SMS Content
Set
password+AP+apn+#+username+#+userpassword
APN:
User Name:
Password:
Inquiry
password+AP
Delete
password+APDEL
17) Wakeup GPRS Online
SMS Command
Return SMS Content
password+GPRSonline
No SMS Return
18) Remote upload historic data via GPRS: Send this command, the unit will upload historic data via
GPRS.
SMS Command
Return SMS Content
password+HIS
Automatically upload all historic data to server via GPRS.
6. Communication Protocol
The GSM 3G M2M RTU supports TCP/IP communication via GPRS/3G. It is very useful for users to create
remotely server. It inbuilt Modbus TCP protocol and definition protocol(KingPigeon RTU Protocol), the user can
connect the GSM 3G M2M RTU to the present HMI, OPC Server, SCADA directly.
For GPRS Communication protocol, please refer to <S27x GSM 3G M2M RTU GPRS/3G Protocol Instruction>.
7. Registers Assignment Table
The registers assignment of the RTU and its IO will definite in the < S27X GSM 3G M2M RTU Register
Assignment Table>, please refer to it.
8. Upgrade Firmware
The GSM 3G M2M RTU supports upgrade firmware via USB port directly. If we upgraded the firmware
functions of the RTU, we will inform you to upgrade the firmware if you required. If there any new
requirements of the present functions caused it should update the firmware, the user can upgrade them
directly by USB port. If you required upgrade, please contact us to modify the firmware according to you
requirements, and we will provide the upgraded firmware to you to upgrade them.
9. Warranty
1) The RTU was warranted to be free of defects in material and workmanship for one year from the date of
purchase.
2) This warranty does not extend to any defect, malfunction or failure caused by abuse or misuse by the
Operating Instructions.
10. Wiring Connection Diagram:
S270 S271 GSM 3G M2M RTU User Manual Page 27 of 27 Ver 2.1 WWW.GPRS-M2M.COM
GSM 3G M2M RTU
Automation solution
1.Analog Transducer:
2.T/H input Sensor (Temperature&Humidity for Environment):
Temp&Hum
Input
VDD
Connect to AM2301 Sensor VDD wire. Red wire.
Data
AM2301 Data wire. Yellow wire.
GND
AM2301 GND, black wire.
- END-
Loading...