KingKar HHO Operation Manual
HHO CARBON CLEANER 6.0 OPERATION MANUAL
1
OPERATION MANUAL
KingKar Eco-technologies Co.,Ltd
HHO Carbon cleaner 6.0
Please read this manual carefully and follow its instruction!
For your safety, please assemble, maintain, check and repair the equipment by the
professionals.
For your safety, please pay much attention to the safety instructions in the manual, and
operate by the professionals.
Please put it together with Certificate of Quality in certain place to ensure the relevant
person can read it at any time.
HHO CARBON CLEANER 6.0 OPERATION MANUAL
2
Special Attention to Operation and Safe
Items
1. In the process of carbon cleaning, if engine flame out unexpectedly, please process
strictly in accordance with the "Annex III: The operation introduction of engine flame out".
2. In the process of carbon cleaning, the connecting tube between engine and machine
must be a negative pressure port, the negative pressure value -20K is appropriate; it is
prohibited pass hydrogen and oxygen gas into the air filter directly.
3. In the process of carbon cleaning, it is forbidden to enter the cab for vehicle operation,
especially step on accelerate.
4. In the process of carbon cleaning, processing the other engine maintenance items is
prohibited.
5. In the process of carbon cleaning, it is prohibited to operate the machine by two people
at same time;
6. In the process of carbon cleaning, it is prohibited to standing front near the car engine.
7. In the process of carbon cleaning, it is prohibited to open automobile air-conditioning,
multimedia and so on;
8. Before using the equipment for carbon cleaning, please check whether the vacuum
sensor is workable, if not, please replaced it by a new one can be used for carbon
cleaning. The above points must be adhered strictly in order to avoid any security
accident.
HHO CARBON CLEANER 6.0 OPERATION MANUAL
3
Content
s
1. Preface -------------------------------------------------------------------------------------------------04
2. Installation ---------------------------------------------------------------------------------------------05
3. The introduction of machine structure ------------------------------------------------------------07
4. Checking before Debugging ----------------------------------------------------------------------12
5. Prepare Work before Start the Machine -------------------------------------------------------- 12
6. The working process of carbon cleaning -------------------------------------------------------13
7. Fault analysis and elimination ---------------------------------------------------------------------15
8. Notice ---------------------------------------------------------------------------------------------------17
9. Maintenance of the Machine ----------------------------------------------------------------------17
Annex I: The work flow chart of HHO Carbon Cleaning Machine ----------------------------18
Annex II: Notice of HHO Carbon Cleaning Machine --------------------------------------------19
Annex III: The operation introduction of engine flame-out --------------------------------------20
Annex IV: Instruction of Electrolytic Solution’s Making and Adding ---------------------------21
Certificate of quality & warranty ----------------------------------------------------------------------24
HHO CARBON CLEANER 6.0 OPERATION MANUAL
4
1. Preface
The manual is the instruction of use, maintenance and safety precautions for HHO Carbon
Cleaner 6.0. File will explain and instruct on how to connect the HHO Carbon Cleaner 6.0
with vehicles, to remove carbon deposits in the car or truck engine, as well as the operation
of the machine's safety precautions and contains the instruction of spare parts, etc.
1.1 Purpose and expected results
With the increasing of engine useful life and the complexity of automobile use environment,
carbon in car engine system will accumulate in the engine block, piston top, catalytic surfaces
and other parts. Carbon deposits will cause engine start performance reduction, fuel
consumption increasing, emissions of non-compliance and other serious problems and
safety hazards. HHO Carbon Cleaner 6.0 takes the advantage of the high-energy
characteristics and catalytic properties of Oxy-hydrogen gas, adds the Oxy-hydrogen gas and
carbon cleaner agent into the engine combustion chamber through the engine idling to
remove carbon deposits inside the engine, restore the original engine performance, improve
throttle response speed and reduce emissions. The fuel will be combusted more efficient,
fuel consumption reduced, engine life extended.
The equipment is mainly used for cleaning carbon deposits in vehicle engine system. When
there is a problem of the vehicle as following, please solve the problem before using the
device:
(1) Unstable idle
(2) Piston ring seal failure, burning oil
(3) Spark ignition system of aging
(4) Nozzle clogging
(5) Air intake and exhaust system seal failure
1.2 Operating Conditions
Normal operation requirements of HHO Carbon Cleaner 6.0:
(1) Stable single-phase 220v power supply, carbon cleaning solution and good ventilation.
(2) Applies to the petrol engine and diesel engines,Oxy-hydrogen outlet hose connected
to the negative end of the car's engine intake manifold. Note: If the car traveled 30 minutes
or more before, please open the hood and turn off the engine to rest 10 minutes to make
sure the engine idling normally. Please make sure the fuel supply is enough during
operation.
HHO CARBON CLEANER 6.0 OPERATION MANUAL
5
2.
Ins
tallatio
n
2.1 Before installation, please confirm:
(1) HHO Carbon Cleaner 6.0 should be installed on the ground of the smooth, clean and stable
ground.
(2) The equipment should adopt sing le phase electric power.Please make sure that the circuit
input voltage is ±10% industrial electricity, and establish appropriate ground wire connection.
(3) We recommend placing this machine in open space with good ventilation.
(4) The distance between the car and machine should be less than 10 meters; it is better
control in 5 meters.
2.2 Add carbon cleaning solution in the first time
Note: All overseas customers, due to the customs is prohibited to carry liquid, the machine
we send are without solution. So must add carbon cleaning solution in first time use,
please refer to the annex 4.
2.3 Electrical wiring diagram (only for principle instructions, when using please be subject to
physical machine and operation manual)
Pic-1
HHO CARBON CLEANER 6.0 OPERATION MANUAL
6
Pic-2
1
24V DC interface
2
over temperature detection input
3
over pressure detection input
4
vibration sensor detection input
5
control panel interface
6
gas production adjustment interface
7
cleaner agent and negative pressure detection input
8
water level probe and anti-backfire probe detection input
9
indicator light interface
10
power protection solenoid valve
11
AC contactor interface
12
alarm solenoid valve
13
adding water solenoid valve
14
cleaner agent solenoid valve
15
AC contactor
16
exhaust solenoid valve
1
timer interface
2
panel button interface
3
Control panel interface
4
indicator light interface
HHO CARBON CLEANER 6.0 OPERATION MANUAL
7
3.The introduction of machine structure
3.1 Outside structure
Pic-3（Fro
nt）
Pic-4
（Back）
HHO CARBON CLEANER 6.0 OPERATION MANUAL
8
Pic-5（Control panel） Pic-6（Circuit Control System Module）
3.2 Inside structure
Pic-7（Left-
side）
Loading...