Kingfer Industrial Blue Flame KF-B006-TP User Manual
READ INSTRUCTIONS CAREFULLY: READ AND FOLLOW ALL INSTRUCTIONS.
PLACE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE.
ONLY USE IN A WELL VENTILATED AREA
USER MANUAL
FOR
BLUE FLAME HEATER
with Thermostat
（
KF-B006-TP
（
）
）
WARNING: IF THE INFORM ATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY. A FIRE OR
EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE. PERSONAL
INJURY OR LOSS OF LIFE
SAFETY PRECAUTIONS
1. Always use heater in accordance with
instructions supplied with each heater.
Keep instructions in a safe place.
2. DO NOT place clothes or other materials
on the heater. This could cause a fire risk
and/or affect the efficiency of the appliance.
3.
DO NOT position heater close
furniture.
4. DO NOT move heater from room to
room when lit.
5. DO NOT position heater close to
walls, furniture, net curtains, bed
linen or any other inflammable
materials as this could result in the
risk of fire. The following minimum
distances should be respected;
100cm from side, 200 cm from front.
ALWAYS face heater towards center
of room. The heater should be
positioned on a level surface at all
times.
6. If a leak is suspected, turn the gas off at
the cylinder. DO NOT disconnect the
regulator. Check all connections. Slowly
turn the gas on and brush the
connections with soapy water or liquid
detergents a gas leak will form bubbles.
If a leak is found, turn the gas off. DO
NOT use the heater again until it has
been checked by a competent person
in accordance with the Gas Safety
(installations and use) Regulations 1998
1
USING ENVIRONMENT
Number of radiant
continuously IN USE
ROOM SIZE
VENTILATION
Low level
High level
1
40 cubic metres - 4m*4m*2.5
40cm2
40cm2
2
70 cubic metres - 7m*4m*2.5
70cm2
70cm2
3
105 cubic metres - 105m*4m*2.5
105cm2
105cm2
1. This appliance requires a hose and a regulator.
2. Only use in well ventilated areas.
3. Do not use in vehicles, caravans or auto caravans.
4. Do not attempt to use in high-rise flats, basements, bathrooms or bedrooms.
5. This appliance should be tested for leaks before initial use and whenever the
6. It is important that all gas connections have been correctly made to prevent
2
Your heater consumes oxygen while it is in function. For that reason, adequate ventilation
should be provided in rooms in which the heater is used. This ensures the removal of
products of combustion and allows the entry of replacement air.
Adequate ventilation should considerably reduce the possibility of condensation
occurring. The following table shows the smallest sizes of room suitable for each heat
setting and the ventilation.
FOR BLUE FLAME HEATER MODELS:
cylinder is re-connected.
any leakage. Do not use naked flame to test for leaks. Use soapy water.
7. Always use your cylinder always in an upright position.
8. Always turn off the regulator control when the heater is not in use.
9. When lighting your heater for the first time or after a period of time has
10. Do not use your heater while sleeping.
11. Do not use your heater in high-rise flats.
12. Do not use your heater in basements, bathrooms or bedrooms.
13. This appliance requires a hose and a regulator, check with your gas supplier for
14. The guard on the appliance is to prevent risk of fire or injury form burns and
15. For the Pusher Igniter unit, it need to be installed a AAA battery
3
passed since the last use, light the heater outside and burn outdoors for 15
minutes.
the correct type according to the cylinder being used and any regulations at
the time.
no part of it should be permanently removed. It does not give full protection
for young children or the infirm. We would recommend a fireguard to be
fitted.
Loading...