KINGDOM KFE2201C Instruction Manual

Kingdom New 1 Cue Wireless Firing System

KFE2201C

Instruction Manual

Contents

Disclaimer----------------------------------------------------------P2
Warning-------------------------------------------------------------P2
Description---------------------------------------------------------P2
Technical date------------------------------------------------------P3
What is included---------------------------------------------------P3
What is not included----------------------------------------------P3
Deprogramming Module and Re-Programming---------------P3
Firing Mode Definitions------------------------------------------P3

Single Fire
All Fire
Sequence Fire

Step Fire

How to program ---------------------------------------------------P4
Over-loading protection------------------------------------------P5
Optional Upgrade--------------------------------------------------P5

Page 1of 6

Disclaimer:

The manufacturer(s), distributor(s) and / or seller(s) accept no responsibility
whatsoever for any damage, injury or loss, financial or otherwise, resulting
directly or indirectly from the use, misuse, function or malfunction of this device.
By purchasing and using this device you understand and accept this disclaimer.

Warning:

1. Only the person who has fireworks license is allowed to purchase the product,
or the person of whom there isn’t fireworks purchase limit in his/her country or
district is allowed to purchase the products. Kingdom is not with responsibility for
any illegal usage.

2. Safety is the user’s responsibility. All pyrotechnic effect and firework safety
guidelines should be followed completely.
3, You must deprogram the system prior to trying to re-program the module to
prevent accidental code storage thereby creating a secure firing environment

Description:

This new 1 cue Firing
System has been designed
to fill the needs of those
pyrotechnicians who need
smaller cue counts that can
be spread around the shoot
site thus saving in wire and
clutter. It is also widely
used for the wedding
celebrations, part shows,
stage performance, movie
special effects and some
special occasions.
Additionally, this system is
capable of igniting
consumer grade clip style
igniters and professional grade e-matches.

Receiver module Transmitter 1

Transmitter 2(KFC2201C/60)

Page 2 of 6

Technical date sheet:

Module Size (cm) 5.5 x 5 x 4 Inner power (V) 4 x 1.5v AAA batt e ri es

Unit weight (kg) 0.05 Test current (MA) 0.9

Range (meter) 150 Output power(V) 6.0

What is included:

12 Pieces of Individual Receiver Modules .
1 Piece of 3x20channel Transmitter-KFE2201C/60
1 Instruction Manual.

What is not included:

Batteries for Modules and Transmitter.

Deprogramming module and re-programming

You must deprogram the system prior to trying to re-program the module. This
system has a fail-safe for digital rectifying that will prevent accidental code storage
thereby creating a secure firing environment..

Step 1. Press and hold the
illuminate for about 10 seconds. This LED light will go out when the code is deleted.

Step 2. Ensure that the transmitter(KFE2201C/60) is on and the slide switch is in 1-3
position. Extend the antenna on the receiver module. Press and release the
(program) button again. Immediately, press any button of the transmitter. Keep your
fingers on the button until you see the signal LED blink. Which indicates the receiver
module has locked onto the signal.

Step 3. You can test the receiver module by pressing the corresponding firing button
on transmitter.

Firing mode definitions:

Single Fire: Fire individual cue.
All Fire: Will fire all cues from all the receiver modules on the selected firing button
on transmitter at once.

P (program) button. The red LED above the button will

P

CONT (Sequence Fire): Will fire all cues in sequence from one receiver module to
another with a pre-set time delay between cues. There is the time marks below the
firing buttons of transmitter.
Step Fire: Every time you push the step firing button on transmitter a cue will fire
from one receiver module to another.

How to program:

1. Single fire:

Set the communication between receiver and any firing button from 1-20. The
corresponding firing button can control the receiver module.

2. Sequence fire: Example receiver modules A, B, C.
Step 1. Set the communication between receiver A and firing button 1.

Set the communication between receiver B and firing button 2.

Set the communication between receiver C and firing button 3.

Step 2. Select the time delay button (Example button 17. the time delay is 2

second). Keep pressing this button, then press and release the

receiver modules A,B,C. You will see the signal LED will blink twice.
Step 3. Press CONT firing button, then every cue of receiver modules will fire at a
time delay of 2.0 seconds.

3. Step fire: Example receiver modules A, B, C.
Step 1. Do the same as Step 1 (in sequence fire mode above)
Step 2. Keep Pressing STEP firing button, then press and release the

receiver modules A,B,C. You will see the signal LED will blink twice.

Step 3. Every time press

4. All fire: Example receiver modules A, B, C.
There is two way to program it.
1, Do the same steps as Step 1(in sequence fire mode above)
Keep pressing ALL firing button, then press and release the
modules A,B, C. You will see the signal LED will blink twice. Then press the ALL
button. All the cues from A, B, C receivers will fire together.

2. Select one firing button from 1-20. For example, we choose button 1. Set the
communication between each receiver module and firing button 1. then press
button 1, all the cues from A, B, C receiver modules will fire together.

STEP

firing button, a cue will fire from receiver A to B to C.

P buttons on receiver

P buttons on

P buttons on

Page 3 of 6 Page 4 of 6