King Controls 9702, 9702-LP Installation And Operating Instructions Manual
Automatic Satellite System
9702 9702-LP
Installation and Operating Instructions
11200 Hampshire Avenue South, Bloomington, MN 55438-2453
Phone: (800) 982-9920 Fax: (952) 922-8424
www.kingcontrols.com
1347 REV M
Satellite Solutions for Mobile Markets
®
Page 1
IMPORTANT!
The satellite TV market is expanding and changing. The information in this manual was
accurate at the time of printing. If your King-Dome does not operate as outlined in this
manual please call King Controls at (800) 982-9920 or visit our website at
www.kingcontrols.com.
TABLE OF CONTENTS
Section Contents Page
1. INTRODUCTION.....................................................................................2
2. DEFINITION OF TERMS........................................................................3
3. INSTALLATION..................................................................................4-11
4. OPERATION .........................................................................................12
5. MULTI-SWITCH ....................................................................................13
6. TROUBLESHOOTING..........................................................................14
7. MAINTENANCE....................................................................................15
8. LIMITED WARRANTY ..........................................................................16
DIRECTV®is an official trademark of DIRECTV, division of GM Hughes Electronics Corporation.
Dish Network®is an official trademark of Echostar Communications Corporation.
Bell ExpressVu
®
is an official trademark of Bell Canada.
DVB®is a trademark of the DVB Digital Video Broadcast Project (1991-1996)
Page 2
The King-Dome Automatic Satellite System includes 2 main components (Fig. 1).
Dome (Antenna) Unit Located on the roof of the vehicle. The dish is covered by a
protective dome that keeps operational components free from
the elements.
Controller Located in the vehicle. Activates the search mode and
provides limited diagnostic functions using the status light.
SECTION 1
INTRODUCTION
Note: A TV, satellite receiver, and program subscription are also required for satellite TV
viewing. (Not supplied by King Controls.)
Fig. 1
KING CONTROLS
POWER
STATUS
ON / SEARCH
OFF
ON/SEARCH
OFF
SWITCH
SATELLITE
STATUS
KING-DOME
Page 3
AZIMUTH: Circular rotation around the vehicle.
(like a clock face: front of vehicle is 12:00, rear is 6:00) (Fig. 2)
ELEVATION: Angle in degrees measured from the ground plane (Fig. 3).
SIGNAL STRENGTH: Intensity of electronic signal received from the satellite transmission.
SECTION 2
DEFINITION OF TERMS
Fig. 2
Fig. 3
KIT CONTENTS:
1. Unpack and identify all components (Fig. 4).
Page 4
SECTION 3
INSTALLATION
Fig. 4
TOOLS AND MATERIALS REQUIRED:
- drill and drill bit set
- tape measure
- 7/16” open end wrench (coax connections)
- adhesive sealant (compatible with roof material)
- appropriate fasteners to install all components and wiring
- 5/32” allen wrench, channel lock or pliers (to remove shipping bolt)
- wire cutter (to remove shipping tie strap)
POWER
STATUS
ON / SEARCH
OFF
Optional
Wall Mount
Controller
King Dome Operating Instructions
1. Turn tv and satellite receiver on.
The tv screen should display “searching for
satellite signal” or “Acquiring satellite signal.
IMPORTANT Do not use the tv or receiver
controls until you have found a satellite.
2. Press and hold the king dome switch to
on/search for a full 4 seconds.
3. wait for status light to turn stead green.
4. turn to a satellite channel that you normally
watch. Is there a picture?
questions? refer to owner’s manual
KING-DOME
KIT CONTENTS
SWITCH
SATELLITE
STATUS
ON/SEARCH
OFF
Page 5
IMPORTANT! The tie strap and spacer, and the bolt and washer must be removed from
the bottom of the dome unit prior to installation. DO NOT REMOVE THE
DOME COVER TO REMOVE THESE SHIPPING RESTRAINTS.
YOU MUST PLUG THE SHIPPING BOLT HOLE WITH THE SUPPLIED PLUG.
2. Remove and discard the tie strap and spacer, and the bolt and washer that pass through
the bottom of the base (Fig. 5).
3. Insert provided plug into hole that was occupied by the shipping bolt (Fig. 5).
Fig. 5
IMPORTANT!
Remove and discard
Tie Strap and Plastic
Spacer prior to
installation.
IMPORTANT!
Remove and discard
Bolt and Washer
prior to installation.
IMPORTANT!
After removing shipping bolt, firmly insert plug
into hole. Plug should be almost flush with base.
Loading...