King Controls 1500-HD, 1800-HD Installation And Operating Instructions Manual

11200 Hampshire Avenue South, Bloomington, MN 55438-2453

Phone: [phone] Fax: [phone]

www.kingcontrols.com

20339 REV B

Satellite Solutions for Mobile Markets

MEMBER

®

®

Gyro Stabilized Satellite TV Antenna

Model 1500-HD
Model 1800-HD

Installation and Operating Instructions

Page 1

IMPORTANT!

The satellite TV market is expanding and changing. The information in this manual was accurate at the
time of printing. If your Sea-King does not operate as outlined in this manual please call King Controls at
[phone] or visit our website at www.kingcontrols.com.

Please read this entire manual before beginning the installation.

DISH NETWORK - EXPRESSVU: If you plan to use the Sea-King with multiple satellite programming and
would like to use the auto-switching feature, your receiver must be configured.

To configure the DISH receiver for automatic satellite switching, the antenna must be on the ground, dock
or motionless platform with no movement (see pages 24-27).

DIRECTV: This antenna will receive available HDTV programming from DIRECTV Ku band satellites at
101°, 110° and 119° with a properly installed HD converter accessory #9747 (included). It will not receive
channels broadcast from DIRECTV’s Ka band satellites at 99° and 103°.

TABLE OF CONTENTS

Section Contents Page

1. INTRODUCTION............................................................................................................2

2. DEFINITION OF TERMS...............................................................................................3

3. INSTALLATION.........................................................................................................4-17

4. OPERATION...........................................................................................................18-21

5. AUTOMATIC SATELLITE SWITCHING: DIRECTV®..............................................22-23

6. AUTOMATIC SATELLITE SWITCHING: DISH NETWORK

TM - EXPRESSVU.........24-27

7. TROUBLESHOOTING............................................................................................28-31

8. MAINTENANCE...........................................................................................................32

9. LIMITED WARRANTY .................................................................................................33

DIRECTV®is a registered trademark of DIRECTV, Inc.
Dish NetworkTM is an official trademark of Echostar Communications Corporation.
Bell ExpressVu is an official trademark of Bell Canada.
DVB is a trademark of the DVB Digital Video Broadcast Project (1991-1996)

ELECTRICAL HAZARD WARNING!

The coaxial cable that connects the dome unit to the tuner carries a

24 volt electrical current. Exercise extreme caution when handling

this cable. Do not cut, break, or splice this line. Do not insert or

connect any devices such as splitters or any other device for any

reason. This line is not compatible with any other equipment.

Damage will occur to any device other than the dome unit if

connected to the antenna port on the tuner.

The Sea-King Fully Stabilized Marine Satellite System includes 6 main components (Fig. 1).

Dome (Antenna) Unit Mounted on the vessel. The dish is covered by a protective

dome that keeps operational components free from the
elements.

Controller Located in the vessel. Used to activate and monitor the

system, and access programming and diagnostic information.

Tuner Located in the vessel. Decodes the satellite signal so the

Sea-King locks onto and tracks the correct satellite.
HDTV Converter Box Enables viewing of HDTV signals from DIRECTV 110 satellite.
Multi-switch Installed for multiple receiver hookup (DIRECTV only).
Power Supply Located in the vessel. Supplies proper operating voltage to the

Sea-King.

SECTION 1

INTRODUCTION

Page 2

Fig. 1

Note: HDTV Converter/Multi-switch installed for DIRECTV HD only.

Overview only: see Installation Section for wiring schematics.

Note: ATV, satellite receiver, and program subscription are also required for satellite TV viewing (sold separately).

You must have an HD Receiver, HDTV Monitor (TV), the proper HD cables (component video or HDMI) and
the appropriate programming subscription in order to view HD programming (sold separately).

AZIMUTH: Angle in degrees measured clockwise from Magnetic North (0°) (Fig. 2).

SIGNAL STRENGTH: Intensity of electronic signal received from the satellite transmission.

SECTION 2

DEFINITION OF TERMS

Fig. 3

ELEVATION: Angle in degrees measured from a level plane (Fig. 3).

Page 3

Fig. 2

KIT CONTENTS:

1. Unpack and identify all components (Fig. 4).

Page 4

SECTION 3

INSTALLATION

TOOLS AND MATERIALS REQUIRED:

• drill and drill bit set

• tape measure

• 7/16” open end wrench (coax connections)

• 5/32” allen wrench, channel lock or pliers (to remove shipping bolt)

• 1/8” allen wrench or phillips screw driver (to remove dome cover)

• appropriate fasteners and tools to install all components and wiring

• adhesive sealant, compatible with vessel material

Fig. 4

Page 5

DOME LOCATION

1. Select an area on the vessel for the dome unit, keeping in mind the coax cables will enter
the vessel through the surface directly beneath the dome unit. Use the following criteria:

a) The shortest distance between the dome unit and the main satellite receiver is most

desirable.

b) The dome unit requires a 16.5” (model

1500-HD) or 20” (model 1800-HD)
diameter mounting area on the vessel
surface. You may also use an industry
standard mount. (Call King Controls or visit

www.kingcontrols.com for more information.)

Exact hole spacing is shown at right.
Distances are to centers of holes.

c) The dome unit should never be mounted so that it is tilted more than two degrees

in any direction.

d) Keep the dome unit as far away from the radar as possible, and if possible above

the level of the radar.

e) The dome unit should be mounted as close as possible to the center of the vessel

(fore-aft and side to side).

f) The mounting surface must be strong enough not to flex under the weight of the

unit or from vessel vibrations.

g) There must be no “line of sight” obstructions from this location. Items such as

masts or radar antennas that are too close to the dome unit may prevent the
satellite signal from reaching the dish (Fig. 5).

Fig. 5

1. Remove and save the dome cover screws. (Figs. 6A and 6B).

2. Carefully remove the dome cover. Do not allow dome cover to catch on internal
components or wiring.

3. Remove and discard the shipping bolt.

Page 6

COMPONENT LOCATION:

1. Select the location of the internal components using the following criteria:

a) The Controller, Tuner, HDTV Converter, Multi-switch and Power Supply should be in

the same general vicinity of the main satellite receiver, AND ACCESSIBLE FOR

OPERATION AND MAINTENANCE PURPOSES.

b) The Tuner should not be stacked directly on top of

other electronics. If located in a cabinet or other
enclosure, make sure there is adequate ventilation
around the unit. (If using the Tuner mounting

brackets see page 17.)

c) The Controller should be conveniently located

for the end user. (If using the Wall Mount Faceplate,

see page 16.)

d) All components should be secured so they do not shift or bounce around during

vessel motion.

2. Place the components in the selected areas.

REMOVE SHIPPING RESTRAINTS

Note: Reference appropriate figure on next page for your model number:

Model 1500-HD: see Fig. 6A
Model 1800-HD: see Fig. 6B

Page 7

Fig. 6A

Fig. 6B

1500-HD

1800-HD

IMPORTANT!

The shipping bolt must be

removed prior to installation.

IMPORTANT!

CAREFULLYremove the dome

cover. Do not allow dome

cover to catch on internal

components or wiring.

IMPORTANT!

CAREFULLY remove the dome

cover. Do not allow dome

cover to catch on internal

components or wiring.

IMPORTANT!

The shipping bolt must be

removed prior to installation.

Page 8

To verify proper operation of the components, perform a Pre-Installation Check as follows:

1. Place the dome unit in your chosen location and on its mounting pedestal. Temporarily
secure the unit from falling. DO NOT PERMANENTLY MOUNT THE DOME UNIT UNTIL

YOU HAVE COMPLETED THE PRE-INSTALLATION CHECK ON THE NEXT PAGE.

If mounting to the vessel surface, you will need to
temporarily place the dome unit on a pedestal or
blocks to perform the pre-installation check.

IMPORTANT! IF CONFIGURING THE RECEIVER FOR MULTIPLE SATELLITE
SWITCHING WITH DISH NETWORK OR EXPRESSVU, Y0U MUST DO THE
PRE-INSTALLATION CHECK ON A MOTIONLESS PLATFORM SUCH AS THE DOCK
OR GROUND.

EXTREMELY IMPORTANT!

NEVER lift the unit by the LNB assembly, Wave Guide assembly, or the dish.

Lift the unit by the base ONL

Y.

PRE-INSTALLATION CHECK

ELECTRICAL HAZARD WARNING!

The coaxial cable that connects the dome unit to the tuner carries a

24 volt electrical current. Exercise extreme caution when handling

this cable. Do not cut, break, or splice this line. Do not insert or

connect any devices such as splitters or any other device for any

reason. This line is not compatible with any other equipment.

Damage will occur to any device other than the dome unit if

connected to the antenna port on the tuner.

2. Use Figs.10-11 on pages 13-14 to determine your desired wiring configuration.
TEMPORARILY connect system as outlined.

If using both 50’ coax, label the ends of one coax to avoid confusion when making the
connections.

MAKE SURE TO CONNECT POWER LAST.

3. Verify system operates properly as described in Section 4 OPERATION, Page 18.
DISH NETWORK - EXPRESSVU: If configuring the receiver for multiple satellite

switching, do this now while the antenna unit is on a motionless platform (see page 24).

4. After verifying proper operation of the system, DISCONNECT POWER FIRST then all
other components.

DOME INSTALLATION AND EXTERNAL WIRING

Fig. 7

IMPORTANT! USE ONLY THE COAX CABLES SUPPLIED WITH THE SEA-KING.

COIL

AND STORE EXCESS CABLE IN THE CABINET WITH THE COMPONENTS.

DO NOT CUT COAX.

If coax cable other than that supplied with the Sea-King is used, the following guidelines
must be followed:

1) Ends must be terminated with SNAP-N-SEAL

®

connectors (Fig. 7.)

(DO NOT USE TWIST-ON OR HEX-CRIMPED CONNECTORS.)

2) Cable must be RG6 and rated at 2.2 GHz or higher.

IMPORTANT! Rubber O-rings must be REMOVED from ends of all SNAP-N-SEAL®connectors.

Page 9

Page 10

IMPORTANT! Make sure power supply is disconnected from 110 volt source before continuing with

permanent installation.

The installer is responsible for weatherproofing all holes in the vessel.

Note: The installer is responsible for determining the most appropriate fastener to secure the dome unit to the

pedestal or vessel surface. Depending on the surface material, fasteners such as lag screws, sheet metal
screws, toggle bolts and T anchors may be used.

1. Determine the path of the coax cable(s) from the dome unit to the internal components.
Drill necessary holes (3/4”) in vessel surface where coax will enter vessel. Route coax
cable(s) leaving enough slack to attach to, and mount, dome unit.

2. Apply foam gasket(s) to bottom of dome unit (Fig. 8).

Note: The Sea-King is wired for multiple receiver support. There are two coax ports on the bottom of the dome

unit. The one labeled “MAIN” MUST be connected to the Tuner (IDB) in vessel. The unlabeled port can be
used for an additional receiver (see page 13).

IMPORTANT! You must fill the ends of all external coax cables with the supplied dielectric grease.

Fig. 8