1730 Five Points Lane • Fuquay-Varina, NC 27526
1-800-800-6296 • www.kingcanopy.com
WARNING:
Keep all ame and heat sources
away from this tent fabric. Meets
the ammability requirements of
CPAI-84 Section 6 and NFPA-701.
It is not re proof. The fabric will burn if
left in continuous contact with
any ame source.
Page 2
PARTS LIST
3X4-2PCS-AT-A 16 pc 2”x39.5” Silver Swedge Pipe
2X0-2PCS-AT-B 8 pc 2”x23.75” White Swedge Pipe
2X7-2PCS-AT-C 8 pc 2”x31.125” Silver Swedge Pipe
3X4PCS-AT-D 15 pc 1.375”x39.75” Silver Pipe
3X4PCS-AT-E 15 pc 1.375”x39.75” Silver Swedge Pipe
3W2PCS-AT-R 2 pc 3-way Connectors - Silver Right Side
3W2PCS-AT-L 2 pc 3-way Connectors - Silver Left Side
3W215PC-AT 2 pc 3-way Connectors - White (Peak Ends)
4W2PCS-AT 4 pc 4-way Connectors - Silver (Sides)
4W215PC-AT 2 pc 4-way Connectors - White (Peak)
SC215-AT 4 pc 3-way clamp
DC215-AT 4 pc 4-way clamp
16 pc 5/16” x 2.5” Bolts
12 pc 5/16” x 2” clamp bolts
28 pc 5/16” Nuts & washers
BALL 65 pc Elastic ball straps
ATC1220S 1 pc Fitted Cover with attached sidewalls
R
Peak
Peak
L
AT12047EWZS 2 pc End walls with zippers
FOOT2PCS-AT 8 pc Foot pads
A15-CC 8 pc Anchors with cable
U-CLAMP 8 pc U-clamps for Anchors
CBL-AT 4 pc Woven Steel™ Cable
Page 3
ROOF FRAME ASSEMBLY
Step A
Separate all pieces for the roof section rst according to size and shape and arrange per the illustration shown
below.
Left Corner
3-Way
White
connectors
used in
center peak
assembly
Right Corner
3-Way
Step B
Start with the center and complete the center frame rst. Then assemble each side. You will be using the
5/16”x2.5” bolts and nuts for the roof frame assembly. Make sure the bolt holes in the pipes are aligned and
facing away from the cover so they do not make contact with cover and puncture it. Also at this point you will
need to install the Woven Steel™ Cable at each roof truss section before totally closing up each section.
L
A
A
B
B
B
B
A
A
R
D
D
D
E
A
B
E
B
A
E
D
D
D
E
A
B
E
B
A
E
D
D
D
E
A
B
E
B
A
E
Right Corner
3-Way
R
L
Left Corner
3-Way
5/16”x2.5”
Right Corner
3-Way
R
Left Corner
3-Way
L
Page 4
COVER & LEGS ASSEMBLY
Step A
Drape the cover over the the roof frame with the grommets to the bottom facing the roof frame and attach
with ball bungees at each end. You may want to fold the sidewall section back onto the roof frame to keep
it out of your way o the ground until you attach the legs. The sidewalls are long enough to be buried in the
ground to prevent water from running inside.
Step B
Unfold the two zippered end walls and attach using ball bungees following the diagram below.
Start at Peak
Attach Left to Right
Inside View Outside View
Page 5
COVER & LEGS ASSEMBLY
CONNECT THE LEG POLES TO THE ROOF ASSEMBLY.
Step A
First insert the pipes (Parts A & C) for the middle poles into the 3 and 4-way connectors, and then connect the
end leg pipes in the same way. Do the same for the other side. Push the foot pads onto the bottom of each
leg. (See illustration)
NOTE: The foot pads are NOT for anchoring the canopy!
A
Insert Second
C
Insert First
Step B
Now slide the bottom rails through the pockets at the bottom of the sidewalls and attach using the 3 and
4-way clamps and 2” clamp bolts and nuts. Finish securing the cover by attaching the hook and loop down
the ends and on top of the endwalls.
5/16”x2”
5/16”x2”
IMPORTANT! Once the legs and cover are assembled, your canopy will act like a kite in the wind. It is
imperative that the canopy anchors be installed NOW!
Page 6
ANCHORING YOUR UNIT
This canopy is designed for use as a temporary structure. After assembly, the canopy MUST BE securely
anchored to the ground to prevent damage from winds. Your canopy will act like a kite in the wind if not
properly and securely anchored to the ground. Severe winds will cause the frame to twist and unanchored
legs will fall, thereby collapsing the canopy. If severe winds are expected, you must remove the cover from
the frame to prevent damage.
We recommend anchoring your canopy at each corner foot
and center foot on each side. Screw anchor into ground next
to canopy foot using a large screw driver (1). Looping the
cable through the anchor eye will keep it out of the way while
turning. Tilting the anchor slightly will help the anchor to cut
into the ground. Apply downward pressure while turning the
anchor into the ground. Leave approximately three inches of
anchor out of the ground.
Unloop the cable from the anchor eye and slide the clamp onto
cable (2). Run cable around the pipe, and then back through
the clamp. Pull the cable as tight as possible through the
clamp. Hold the cable and tighten clamp with an adjustable
wrench.
When you have tightened the clamp and satised that the
cable will not slip, you may tighten the cable more by turning
the anchor further in the ground as seen in Diagram (1).
(2)
(1)
Page 7
IMPORTANT NOTICE: PLEASE READ CAREFULLY
We are condent that you will be completely satised with your King Canopy unit. Please take a moment
to read the very important information below, and call us with any questions you may have.
King Canopy/PIC America, LTD. has no control over wind, snow, ice, rain or any other weather condition and
we are in no way responsible for any damage caused by the canopy or to the canopy. We suggest you contact
your insurance carrier just as you would for any other outside structure.
OTHER PRECAUTIONS WHICH MUST BE FOLLOWED:
Keep all ame and heat sources away from this tent fabric. The tent fabric will burn if left in continuous
contact with any ame source.
DO NOT cook underneath or near canopy.
DO NOT store or use ammable liquids underneath or near canopy.
DO NOT ignite or store reworks underneath or near canopy.
DO NOT use bleach to clean cover.
DO NOT dry clean cover.
DO NOT wash cover in washing machine or dry in dryer. Hand wash with mild soap and water only.
DO NOT allow rain water, snow or ice to accumulate on top of cover.
DO NOT hang or suspend anything from the frame, grommets, truss system or ball straps of the unit.
REMOVE canopy cover before a storm, or disassemble entire canopy unit if possible.
REMOVE rain water, snow and ice from canopy cover.
This is a temporary structure and is not recommended for use as a permanent structure.
The King Canopy Atlas™ Extra-Duty Garages are designed to be one of the strongest and most well designed
garages in production today. This innovative product oers numerous features and benets for the end
use consumer. Key features include a commercial grade PE fabric skylight that allows sunlight to enter and
“Pass-Thru” front and rear doors that make storing automobiles, boats, ATVs or personal watercraft a breeze!
Our patented Woven Steel™ Cable Roof Truss System is included for increased stability and durability in extreme
weather conditions and able to withstand signicantly heavier loads than frame systems that do not include
this outstanding feature. Easy to assemble and engineered for maximum protection. Includes one year limited
warranty. (Please see enclosed instruction sheet for details.)
***The Woven Steel™ Cable System will not guarantee that your King Canopy Garage/Carport will hold heavy loads (snow
specically) indenitely. Any signicant snow accumulation must be removed frequently to avoid the possibility of PE fabric
failure and steel frame collapse.***
Page 8
PRODUCT INFORMATION
Defective Parts
We try our best to eliminate any defective parts that are shipped with our products. If, however, you should nd
a defective part, we will replace – free of charge – any part which is defective. You will need to provide proof
of purchase showing date of purchase and provide us with detailed description of the defective component.
Your replacement will be shipped by ground shipping, freight prepaid. Next day or express shipping will
require freight collect and paid for by you, the consumer. Damages from improper anchoring, strong winds,
snow, ice or rain are not considered defects.
Improper Anchoring, Strong Winds, Rain Snow, or Ice
King Canopy/PIC America, LTD. does not guarantee these canopies under strong weather conditions. These
canopies are designed to protect against damages caused by sun, rain, tree sap, birds, etc. They are not designed
to hold roof loads that accompany snow, ice or heavy rains. If your canopy is not anchored securely, it can be
lifted by the wind and will y away. If your canopy takes ight, we are not responsible for any replacement. If
you know strong weather is predicted, remove the cover or take down the canopy unit completely. The cover
is designed to be quickly and easily removed.
Warranty
All components of this canopy feature a 1-year limited warranty and are warranted to be free from defects in
material and workmanship for a period of 1-year. You must complete and return the enclosed warranty card
promptly after purchase. Please retain your proof of purchase receipt; you will be asked to provide this receipt
in order to obtain warranty service.
Non-Warranty Replacement Parts
If after expiration of the warranty period, you require replacement parts please contact us at 1-800-800-6296.
We stock replacement parts and make them available to you at discounted prices. Our customer service
department will be pleased to assist you in any way possible.
Certain regions of the country are extremely hard on covers of any kind. Normal wear and tear is not covered
under the warranty, and should be expected.
In order to receive a discounted or free replacement part, you may be asked to return the part, freight prepaid,
to our warehouse for inspection before we will send a replacement. You must, in all cases, provide a copy of
your receipt showing the date of purchase, model number and price.
For missing parts, replacement parts or any questions:
Please Call 8:00am – 5:00pm EST, Monday – Friday
1-800-800-6296 or 1-919-552-2977
Or you can fax us at: 1-919-552-5069
Replacement parts and customer service is also available through our website.
Please visit us at www.kingcanopy.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.