King Canopy VY10030 Owner Manual

10’X20’ HERCULES EXPRESS 8 LEG

ITEM #: C281020PTCLT

Dimensions:

10ft. 8in. Wide x 20ft. Deep x 6ft. 8in. Side Height / 9ft. 9in. Center Height

WARNING:

Keep all ame and heat sources

away from this tent fabric. Meets

the ammability requirements of

CPAI-84 It is not re proof

The fabric will burn if left in

continuous contact with any

ame source.

1730 Five Points Lane • Fuquay-Varina, NC 27526

Distributed by: PIC America, LTD.

1-800-800-6296 • www.kingcanopy.com

PARTS

PTCL1020TW

PTCL1020VS

BALLW

PSLEEVE

PFOOT2

6X6PC

5X8PC

Packed inside the
6X6-2PC Pipe

6X6-2PC

4WPC

3WPC

6X6PC 9 pc 78” Powder Coated Pipe
6X6-2PC 8 pc 78” - 2” Powder Coated Pipe
5X8PC 8 pc 68” Powder Coated Pipe

Packed inside the
6X6-2PC Pipe

3WPC 6 pc 3-way Connectors
4WPC 6 pc 4-way Connectors
BALL50W 50 pc Elastic Ball Straps
PFOOT2 8 pc 2” Plastic Foot Pads
PTCL1020TW 1 pc Tan & White Fitted Cover
PTCL1020VS 4 pc Valance Straps
PSLEEVE 8 pc Plastic Sleeve Inserts for Legs

FRAME ASSEMBLY

4WPC

4WPC

3WPC

3WPC

6X6PC

6X6PC

6X6PC

5X8PC

6X6PC

5X8PC

5X8PC

3WPC

6X6PC

5X8PC

6X6-2PC

6X6-2PC

4WPC

6X6-2PC

4WPC

6X6PC

6X6-2PC

3WPC

3WPC

6X6-2PC

6X6-2PC

4WPC

6X6PC

6X6-2PC

4WPC

6X6PC

6X6-2PC

3WPC

1)

Start by laying out all of the parts and pieces to your King Canopy. Please refer to the

5X8PC

5X8PC

6X6PC

5X8PC

5X8PC

parts list to ensure that your kit is complete. When all the parts have been accounted

for, begin to layout the perimeter of your frame according to the photo above (6X6PC &

5X8PC). Each 3-way tting (3WPC) should be placed at all four corners and two end peaks.
The 4-Way ttings (4WPC) are placed at the center leg and roof sections. The 6X6-2PC Pipes

are used for the legs.

2) Now that all the pipe and ttings are

laid out as displayed in the photo, begin

3) Once the center frame work is fully

connected start assembling the left and

to connect the center pipe and ttings.

Start assembly by working from one end

to the other, connecting the center ridge

pipe into the 3-Way (3WPC) and 4-Way
(4WPC) ttings.

right sections of the frame. Starting at

one end, begin to connect the 5X8PC
pipe to the assembled center ridge. Next

connect the corner 3-Way & 4-Way ttings
to the perimeter 6X6PC pipe.

FRAME & ATTACHING COVER

Length

Width

4) Once one side is complete, move to
the opposite side of the unassembled
frame lifting the frame and connecting

the remaining 5X8PC pipe. Continue

previous steps until all pipe and ttings
are connected.

5) Now that the roof frame work is
complete, you can begin to attach the
tted cover. Start by laying out the cover
to determine which way it is folded, the
length or width or the frame.

6) Grab each end and drape the cover
over the frame centering the cover to

the roof frame work.

7) Starting at opposite corners, attach
the cover with the elastic ball straps by
inserting the elastic cord of the ball strap
underneath the cover and through the
grommet. Then pull taught until the ball
stops.

ATTACHING COVER

8) Wrap the cord around the pole and
secure around the ball.

9) Be sure all four corners are attached
before attaching the remaining ball
straps.

10) Continue attaching straps from left
to right in a zig zag pattern starting at

the two center peaks.

11) Next continue attaching the straps
down each side and end. Make sure the

cover stays centered on the frame.

LEG ASSEMBLY

Insert Second

Insert First

Insert First

12) Now that all the ball straps are

attached. Insert the 6X6-2PC leg pipe
into each plastic foot pad and then insert
a plastic sleeve into the other end of the
leg pipe.

13) Begin to attach the legs to the frame.
Place each leg next to the three and four
way ttings. Starting with the two outside
legs grab the base of the 3-way corner
tting. Lift the frame and insert the open

3-Way tting into the leg. Next insert the

center legs.

15) Repeat step on other side until the
entire unit is standing upright.

15) Pull down and attach the leg skirt

straps to the foot pads at each corner.

Next attach the valance straps by clipping
the plastic hook to the open grommet

hole located on the cover’s valance

(4 total). Hook the plastic ring around the

foot pad and tighten.

attach

hook

& loop

at all 4

corners

COVER ADJUSTMENT

16) Secure the hook and loop straps

on the cover at all 4 corners around the
corner 3-way ttings.

17) Lastly, secure the hook and loop
straps on the corner leg skirts around the

legs.

This canopy is designed for use as a temporary structure. After assembly, the canopy
MUST BE securely anchored to the ground to prevent damage from winds. Your canopy

will act like a kite in the wind if not properly and securely anchored to the ground. Severe

winds will cause the frame to twist and unanchored legs will fall, thereby collapsing the
canopy. If severe winds are expected, you must remove the cover from the frame to
prevent damage. Please follow the anchoring instructions found in the optional anchor

kit available for purchase separately.

IMPORTANT NOTICE: PLEASE READ CAREFULLY

We are condent that you will be completely satised with your King Canopy unit. Please take a moment
to read the very important information below, and call us with any questions you may have.

King Canopy/PIC America, LTD. has no control over wind, snow, ice, rain or any other weather condition and
we are in no way responsible for any damage caused by the canopy or to the canopy. We suggest you contact
your insurance carrier just as you would for any other outside structure.

OTHER PRECAUTIONS WHICH MUST BE FOLLOWED:

Keep all ame and heat sources away from this tent fabric. The tent fabric will burn if left in continuous
contact with any ame source.

DO NOT cook underneath or near canopy.

DO NOT store or use ammable liquids underneath or near canopy.

DO NOT ignite or store reworks underneath or near canopy.

DO NOT use bleach to clean cover.

DO NOT dry clean cover.

DO NOT wash cover in washing machine or dry in dryer. Hand wash with mild soap and water only.

DO NOT allow rain water, snow or ice to accumulate on top of cover.

DO NOT hang or suspend anything from the frame, grommets, truss system or ball straps of the unit.

REMOVE canopy cover before a storm, or disassemble entire canopy unit if possible.

REMOVE rain water, snow and ice from canopy cover.

This is a temporary structure and is not recommended for use as a permanent structure.

WARRANTY INFORMATION

Defective Parts

We try our best to eliminate any defective parts that are shipped with our products. If, however, you should nd
a defective part, we will replace – free of charge – any part which is defective. You will need to provide proof
of purchase showing date of purchase and provide us with detailed description of the defective component.

Your replacement will be shipped by ground shipping, freight prepaid. Next day or express shipping will

require freight collect and paid for by you, the consumer. Damages from improper anchoring, strong winds,
snow, ice or rain are not considered defects.

Improper Anchoring, Strong Winds, Rain Snow, or Ice

King Canopy/PIC America, LTD. does not guarantee these canopies under strong weather conditions. These
canopies are designed to protect against damages caused by sun, rain, tree sap, birds, etc. They are not designed
to hold roof loads that accompany snow, ice or heavy rains. If your canopy is not anchored securely, it can be

lifted by the wind and will y away. If your canopy takes ight, we are not responsible for any replacement. If
you know strong weather is predicted, remove the cover or take down the canopy unit completely. The cover
is designed to be quickly and easily removed.

Warranty

All components of this canopy feature a 1-year limited warranty and are warranted to be free from defects in

material and workmanship for a period of 1-year. You must complete and return the enclosed warranty card
promptly after purchase. Please retain your proof of purchase receipt; you will be asked to provide this receipt

in order to obtain warranty service.

Non-Warranty Replacement Parts

If after expiration of the warranty period, you require replacement parts please contact us at 1-800-800-6296.

We stock replacement parts and make them available to you at discounted prices. Our customer service

department will be pleased to assist you in any way possible.

Certain regions of the country are extremely hard on covers of any kind. Normal wear and tear is not covered

under the warranty, and should be expected.

In order to receive a discounted or free replacement part, you may be asked to return the part, freight prepaid,

to our warehouse for inspection before we will send a replacement. You must, in all cases, provide a copy of
your receipt showing the date of purchase, model number and price.

For missing parts, replacement parts or any questions:

Please Call 8:00am – 5:00pm EST, Monday – Friday

1-800-800-6296 or 1-919-552-2977

Or you can fax us at: 1-919-552-5069

Replacement parts and customer service is also available through our website.
Please visit us at www.kingcanopy.com