King Canada 8365 User Manual

plusplus

performanceperformance

IMPORTANT INFORMATION

5” ANGLE GRINDER

2-YEAR

LIMITED WARRANTY

FOR THIS 5” ANGLE GRINDER

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

LIMITED TOOL WARRANTY

KING CANADA makes every effort to ensure that this product meets high quality and durability standards. KING CANADA warrants to the original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations and lack of maintenance. KING CANADA shall in no event be liable for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products. To take advantage of this warranty, the product or part must be returned for examination by the retailer. Shipping and handling charges may apply. If a defect is found, KING CANADA will either repair or replace the product.

KING CANADA TOOLS

OFFERS A 2-YEAR LIMITED WARANTY

FOR NON-COMMERCIAL USE.

MODEL: 8365

INSTRUCTION MANUAL

SAFETY INSTRUCTIONS

SPECIFICATIONS &

ELECTRICAL INFORMATION

1. Use specified voltage: The tool should not be operated on a power line which exceeds 10% of the voltage indicated on the nameplate.

2. Inspect the tool before each use: operating. Do not use the grinding wheel if there is any breakage or cracks. After assembling the wheel, run the wheel idle for one minute to see if it is safe to use. Then check if all the moving parts are running smoothly without abnormal noise or heavy sparks from the commutator.

void overloading the tool: Do not apply too much pressure on the tool while grinding in

3. A a straight or slanted line. If the speed drops abnormally, the pressure should be decreased immediately. When the tool stops abruptly or is jammed, cut the power supply at once.

4. Replace the carbon brushes in time: brushes should be changed at the same time), or imperfect contact between the brushes and the commutator will result in ring sparks which will damage the commutator or even burn the armature.

5. The tool must not be used in the following cases: insulation of the power cord or the cord guard. If a crack or imperfect contact of the switch, plug and socket and faults such as discontinuous running, heavy sparking, etc. should occur, stop using the tool at once and have it repaired. Do not use until it is repaired.

6. Always keep the tool clean: free from obstruction and care should be taken to prevent iron chips or other foreign matters from entering passage. Recondition immediately after use to keep the tool clean and in the best condition.

7. Use the tool with care: wheel iron from freezing or from becoming damp.

8. Use specified grinding wheel:

resin with depressed center and with a safety linear velocity not lower than 80 meters per second. If the wheel has been kept for more than one year, a rotational strength test should be performed before use.

9. Pay attention to the wheel guard:

ensure safety. Do not operate the tool when the wheel guard has been dismantled. If a substitute is to be used, it should be a steel plate or material with equal strength, whereas brittle materials are strictly prohibited. The opening angle of the guard should not be more than 180 degrees.

10. Places prohibiting the use of the tool:

environements such as environements with moisture, heat, rain or snow or in a place with explosive gas or corrosive vapours.

Handle the tool with care to avoid being bumped and prevent the

The grinding wheel must be inspected cafefully before

Worn out brushes should be replaced (both

If there is any breakage in the

The ventilation passage of the tool should be kept clean and

The wheel used by the grinder must be reinforced fibre

This wheel guard is an important part of the tool to

The tool must not be used in specific

WARNING!: If any parts are missing, do not operate your angle grinder until missing parts are replaced. Failure to do so could result in serious personal injury.

Technical Specifications

Grinding wheel size ................................................................................................5”

Arbor size..............................................................................................................5/8”

Voltage................................................................................................................120V

Amperage ............................................................................................................9.5A

R.P.M. ..............................................................................................................11,000

Cycle/Phase ........................................................................................60Hz, 1 phase

WARNING: YOUR ANGLE GRINDER MUST BE CONNECTED TO A 120V, 15-AMP CIRCUIT. FAILURE TO CONNECT IN THIS WAY CAN RESULT IN INJURY FROM SHOCK OR FIRE.

DOUBLE INSULATION TOOLS. Double Insulation is a design concept used in electric power tools which eliminates the need for the three wire grounded power cord and grounded power supply system. It is a recognized and approved system by Underwriter’s Laboratories, CSA and Federal OSHA authorities.

IMPORTANT: Servicing of a tool with double insulation requires care and knowledge of the system and should be performed only by a qualified service technician. WHEN SERVICING, USE ONLY IDENTICAL REPLACEMENT PARTS OR THOSE RECOMMENDED BY THE MANUFACTURER.

POLARIZED PLUGS: Your tool is equipped with a polarized plug (one blade is wider than the other), this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. To reduce the risk of electric shock, do not change the plug in any way.

EXTENSION CORDS. The use of any extension cord will cause some loss of power. Use the following chartto determine the minimum wire gauge (A.W.G-American Wire Gauge) extension cord. Only use polarized extension cords (one prong wider than the other) which have 2-prong type plugs and 2-hole receptacles which accept the tool’s plug.

For circuits that are further away from the electrical circuit box, the wire gauge must be increased proportionately in order to deliver ample voltage to the angle grinder chart for wire length and size.

. Refer to

WARNING!: Do not use this product as a component of others products. Also, do not use attachments or accessories not recommended for use with this product. Any such use could result in possible serious injury.

ool’s

Amperage

Rating

3-6 6-8

8-10 10-12 12-16

Cord Size in A.W.G.

Cord Length in Feet

150

100

18 18 16 14 12 18 16 14 12

+ 1 hidden pages