KINGBRIGHT TC12-11SRWA Datasheet

30mm (1.2 INCH) 5x7 DOT MATRIX DISPLAY

P/N: TC12-11SRWA SUPER BRIGHT RED

Features



1.2 INCH MATRIX HEIGHT.



DOT SIZE 3mm.



LOW CURRENT OPERATION.



HIGH CONTRAST AND LIGHT OUTPUT.



COMPATIBLE WITH ASCII AND EBCDIC CODES.



COLUMN CATHODE AND COLUMN ANODE

AVAILABLE.



EASY MOUNTING ON P.C. BOARDS OR SOCKETS.



MECHANICALLY RUGGED.



STANDARD : GRAY FACE, WHITE DOT.



RoHS COMPLIANT.

Package Dimensions & Internal Circuit Diagram

Description

The Super Bright Red source color devices are made
with Gallium Aluminum Arsenide Red Light Emitting
Diode.

Notes:

1. All dimensions are in millimeters (inches), Tolerance is ±0.25(0.01")unless otherwise noted.

2. Specifications are subject to change without notice.

SPEC NO: DSAD2436 REV NO: V.5 DATE: NOV/28/2005 PAGE: 1 OF 4
APPROVED: J. Lu CHECKED: Joe Lee DRAWN: Y.L.LI ERP: 1332000506

Selection Guide

Iv (ucd)

Part No. Dice Lens Type

TC12-11SRWA SUPER BRIGHT RED(GaAlAs) WHITE DIFFUSED 4700 24000 Column Cathode

@ 10mA

Min. Typ.

Description

Electrical / Optical Characteristics at TA=25°C

Symbol Parameter Device Typ. Max. Test ConditionsUnits

λpeak

Peak Wavelength Super Bright Red 660 nm IF=20mA

λD

∆λ1/2

C Capacitance Super Bright Red 45 pF VF=0V;f=1MHz

VF Forward Voltage Super Bright Red 1.85 2.5 V IF=20mA

I Reverse Current Super Bright Red 10 uA VR = 5V

Dominant Wavelength Super Bright Red 640 nm IF=20mA

Spectral Line Half-width Super Bright Red 20 nm IF=20mA

Absolute Maximum Ratings at TA=25°C

Parameter Super Bright Red Units

Power dissipation 100 mW
DC Forward Current 30 mA
Peak Forward Current [1] 155 mA
Reverse Voltage 5 V

Operating/Storage Temperature -40°C To +85°C
Lead Solder Temperature [2] 260°C For 5 Seconds

Notes:

1. 1/10 Duty Cycle, 0.1ms Pulse Width.

2. 2mm below package base.

SPEC NO: DSAD2436 REV NO: V.5 DATE: NOV/28/2005 PAGE: 2 OF 4
APPROVED: J. Lu CHECKED: Joe Lee DRAWN: Y.L.LI ERP: 1332000506

Super Bright Red TC12-11SRWA

Remarks:
If special sorting is required (e.g. binning based on forward voltage, luminous intensity/ luminous flux or wavelength),
the typical accuracy of the sorting process is as follows:

1. Wavelength: +/-1nm

2. Luminous Intensity/ Luminous Flux: +/-15%

3. Forward Voltage: +/-0.1V
Note: Accuracy may depend on the sorting parameters.

SPEC NO: DSAD2436 REV NO: V.5 DATE: NOV/28/2005 PAGE: 3 OF 4
APPROVED: J. Lu CHECKED: Joe Lee DRAWN: Y.L.LI ERP: 1332000506

PACKING & LABEL SPECIFICATIONS TC12-11SRWA

SPEC NO: DSAD2436 REV NO: V.5 DATE: NOV/28/2005 PAGE: 4 OF 4
APPROVED: J. Lu CHECKED: Joe Lee DRAWN: Y.L.LI ERP: 1332000506