Page 1
T-1 (3mm) SOLID STATE LAMP
Part Number: L-7104SEC-J3 Hyper Red
Features
z Low power consumption.
z Popular T-1 diameter package.
z General purpose leads.
z Reliable and rugged.
z Long life - solid state reliability.
z Available on tape and reel.
z RoHS compliant.
Package Dimensions
Description
The Hyper Red device is based on light emitting diode chip
made from AlGaInP.
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
SPEC NO: DSAI9730 REV NO: V.5A DATE: DEC/18/2011 PAGE: 1 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1101029050
Page 2
Selection Guide
V
Part No. Dice Lens Type
L-7104SEC-J3
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
* Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Hyper Red (AlGaInP) Water Clear
Iv (mcd) [2]
@ 20mA
Min. Typ. 2θ1/2
2300 4100
*1300 *2400
iewing
Angle [1]
°
34
Electrical / Optical Characteristics at TA=25°C
Symbol Parameter Device Typ. Max. Units Test Conditions
λpeak Peak Wavelength Hyper Red 640 nm I
λD [1] Dominant Wavelength Hyper Red 625 nm I
Δλ1/2 Spectral Line Half-width Hyper Red 25 nm I
C Capacitance Hyper Red 27 pF V
V
F [2] Forward Voltage Hyper Red 2.2 2.8 V IF=20mA
R Reverse Current Hyper Red 10 uA VR = 5V
I
Notes:
1.Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
F=20mA
F=20mA
F=20mA
F=0V;f=1MHz
Absolute Maximum Ratings at TA=25°C
Parameter Hyper Red Units
Power dissipation 84 mW
DC Forward Current 30 mA
Peak Forward Current [1] 150 mA
Reverse Voltage 5 V
Operating/Storage Temperature -40°C To +85°C
Lead Solder Temperature [2] 260°C For 3 Seconds
Lead Solder Temperature [3] 260°C For 5 Seconds
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. 2mm below package base.
3. 5mm below package base.
SPEC NO: DSAI9730 REV NO: V.5A DATE: DEC/18/2011 PAGE: 2 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1101029050
Page 3
Hyper Red L-7104SEC-J3
SPEC NO: DSAI9730 REV NO: V.5A DATE: DEC/18/2011 PAGE: 3 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1101029050
Page 4
PACKING & LABEL SPECIFICATIONS L-7104SEC-J3
SPEC NO: DSAI9730 REV NO: V.5A DATE: DEC/18/2011 PAGE: 4 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1101029050
Page 5
SPEC NO: DSAI9730 REV NO: V.5A DATE: DEC/18/2011 PAGE: 5 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1101029050
Page 6
SPEC NO: DSAI9730 REV NO: V.5A DATE: DEC/18/2011 PAGE: 6 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1101029050
Loading...