Page 1
KP-2012SURC
2.0 x 1.25 mm SMD Chip LED Lamp
DESCRIPTIONS
The Hyper Red source color devices are made with
AlGaInP on GaAs substrate Light Emitting Diode
Electrostatic discharge and power surge could
damage the LEDs
It is recommended to use a wrist band or
anti-electrostatic glove when handling the LEDs
All devices, equipments and machineries must be
electrically grounded
FEATURES
2.0 mm x 1.25 mm SMD LED, 1.1mm thickness
Low power consumption
Wide viewing angle
Ideal for backlight and indicator
Package: 2000 pcs / reel
Moisture sensitivity level: 3
RoHS compliant
APPLICATIONS
Backlight
Status indicator
Home and smart appliances
Wearable and portable devices
Healthcare applications
ATTENTION
Observe precautions for handling
electrostatic discharge sensitive devices
PACKAGE DIMENSIONS
RECOMMENDED SOLDERING PATTERN
(units : mm; tolerance : ± 0.1)
SELECTION GUIDE
Part Number
KP-2012SURC
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity / luminous flux: +/-15%.
* Luminous intensity value is traceable to CIE127-2007 standards.
© 2017 Kingbright. All Rights Reserve d. Spec No: DSAB0861 / 1203000185 Re v No: V.15A Date: 09/14/2017
Emitting Color
(Material)
■ Hyper Red (AlGaInP)
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.004") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to
change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
Iv (mcd) @ 20mA
[2]
Viewing Angle
Lens Type
Min. Typ. 2θ1/2
150 250
Water Clear
140
°
*40 *90
Page 1 / 4
[1]
Page 2
KP-2012SURC
ELECTRICAL / OPTICAL CHARACTERISTICS at T
Parameter Symbol Emitting Color
Wavelength at Peak Emission I
Dominant Wavelength I
F
Spectral Bandwidth at 50% Φ REL MAX
= 20mA
I
F
= 20mA λ
F
= 20mA λ
=25°C
A
Value
Typ. Max.
Hyper Red
peak
[1]
dom
Hyper Red 630 - nm
645 - nm
Δλ Hyper Red 27 - nm
Capacitance C Hyper Red 45 - pF
Forward Voltage I
Reverse Current (V
Notes:
1. The dominant wavelength (λd) above is the setup value of the sorting machine. (Tolerance λd : ±1nm. )
2. Forward voltage: ±0.1V.
3. Wavelength value is traceable to CIE127-2007 standards.
4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure.
= 20mA VF
F
= 5V) I
R
[2]
Hyper Red 1.9 2.5 V
Hyper Red - 10 uA
R
Unit
ABSOLUTE MAXIMUM RATINGS at TA=25°C
Parameter Symbol Value Unit
Power Dissipation PD 75 mW
Reverse Voltage VR 5 V
Junction Temperature Tj 115 °C
Operating Temperature Top -40 to +85 °C
Storage Temperature T
DC Forward Current IF 30 mA
Peak Forward Current I
Electrostatic Discharge Threshold (HBM)
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033.
-40 to +85 °C
stg
[1]
185 mA
FM
-
3000 V
© 2017 Kingbright. All Rights Reserve d. Spec No: DSAB0861 / 1203000185 Re v No: V.15A Date: 09/14/2017
Page 2 / 4
Page 3
TECHNICAL DATA
RELATIVE INTENSITY vs. WAVELENGTH
100%
T
= 25 °C
a
80%
60%
40%
20%
Relative Intensity (a. u. )
0%
350 400 450 500 550 600 650 700 750 800
Forward Current vs.
Forward Voltage
50
T
= 25 °C
a
40
Red
Wavelength (nm)
Luminous Intensity vs.
Forward Current
2.5
2.0
= 25 °C
T
a
HYPER RED
50
40
SPATIAL DISTRIBUTION
T
= 25 °C
a
-60°
-75°
-90°
Forward Current Derating Curve
-30°
-45°
KP-2012SURC
-15°
0.5 0.5
0°
15°
0.01.0 1.0
Luminous Intensity vs.
Ambient Temperature
2.5
2.0
30°
45°
60°
75°
90°
30
20
Forward current (mA )
10
0
1.5 1.7 1.9 2.1 2.3 2.5
Forward voltage (V)
1.5
20 mA
1.0
0.5
Luminous i ntensi ty normalised at
0.0
0 1020304050
Forward current (mA)
REFLOW SOLDERING PROFILE for LEAD-FREE SMD PROCESS
30
20
10
Permis sibl e forward current (mA )
0
-40-20 0 20406080100
Ambient temperature (°C)
TAPE SPECIFICATIONS (units : mm)
REEL DIMENSION (units : mm)
1.5
= 25 °C
a
1.0
T
0.5
Luminous i ntensi ty norm alised at
0.0
-40-200 20406080100
Ambient temperat ure (°C)
Notes:
1. Don't cause stress to the LEDs while it is exposed to high temperature.
2. The maximum number of reflow soldering passes is 2 times.
3. Reflow soldering is recommended. Other soldering methods are not recommended as they might
cause damage to the product.
© 2017 Kingbright. All Rights Reserve d. Spec No: DSAB0861 / 1203000185 Re v No: V.15A Date: 09/14/2017
Page 3 / 4
Page 4
PACKING & LABEL SPECIFICATIONS
KP-2012SURC
PRECAUTIONARY NOTES
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to
the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If
customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening
liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.Kingbright.com/application_notes
© 2017 Kingbright. All Rights Reserve d. Spec No: DSAB0861 / 1203000185 Re v No: V.15A Date: 09/14/2017
Page 4 / 4
Loading...