KINGBRIGHT KASL-4805ZG24S7 User Manual

HIGH BRIGHTNESS LED LIGHT BAR

PRELIMINARY SPEC

Part Number: KASL-4805ZG24S/7 Green

ATTENTION

OBSERVE PRECAUTIONS

FOR HANDLING

ELECTROSTATIC

DISCHARGE

SENSITIVE

DEVICES

Features

z Dimension: 48mm X 5mm X 1.6mm.

z Instant light.

z Linear type.

z High efficiency.

z Long operating life.

z Low power consumption.

z More energy efficient than incandescent,most halogen lamps, and fluorescent lamp.

z RoHS compliant.

Package Dimensions

Notes:

1. All dimensions are in millimeters (inches).

2. Tolerance is ±0.25(0.01") unless otherwise noted.

3.Specifications are subject to change without notice.

SPEC NO: DSAI8687 REV NO: V.1 DATE: NOV/14/2008 PAGE: 1 OF 8
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP:1209000079

Precautions

1. Do not touch the lens with any sharp object.

2. No stress should be applied on the lens.

3. Thermal grease between the light bar and heat sink is recommended to fill air gaps for better thermal conductivity.

4. For securing the LED light bar, M2 screws are recommended. The light bar should not be bent or stressed in any way

which could damage the internal circuit.

5. To prevent damages caused by electrostatic discharge (ESD), it is recommended to wear proper gear such as

wristband or anti-static gloves when handling the product.

6. Constant current source is recommended to power the light bar. When more than one light bar are used, they should

be connected in series if possible.

7. Thermal management should be taken into consideration when using the product. Maximum driving current

should be reduced accordingly at higher ambient temperature to prevent overheating.

8. Soldering recommendations:

z Soldering iron power should not exceed 40W, and should not be in contact with the joint for more than 3.5 secs.

z The maximum soldering temperature should be less than 350°C.

z Do not touch the product immediately after soldering.

z Not reflow compatible.

SPEC NO: DSAI8687 REV NO: V.1 DATE: NOV/14/2008 PAGE: 2 OF 8
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP:1209000079

Absolute Maximum Ratings

Parameter Symbol Rating Units

Forward Current I

Forward Pulse Current [1] I

Power Dissipation P

LED Junction Temperature T

F 700 mA

FP 1000 mA

d 8.12 W

j 120 °C

Operating Temperature Topr -30~+100 °C

Storage Temperature Tstg -40~+120 °C

Case Temperature T

Note:

1. 1/10 Duty Cycle, 0.1ms Pulse Width.

c 100 °C

Electrical / Optical Characteristics

Part Name Device Parameter Symbol Min. Typ. Max. Units Conditions

Forward Voltage [2] V

Luminous Flux [3] Φv 160 195 - lm I

Wavelength at peak emission[4] λpeak - 515 - nm I

F 8.6 10 11.6 V IF=700mA

F=700mA

F=700mA

Dominant Wavelength λdom - 525 - nm I

Spectral bandwidth at 50%Φ

REL MAX Δλ1/2 - 30 - nm IF=700mA

Temperature coefficient of λpeak TCλpeak - 0.14 - nm/°C I

KASL-4805ZG24S/7 Green

Temperature coefficient of λdom TCλdom - 0.11 - nm/°C I

Temperature coefficient of Forward

Voltage

Thermal Resistance R

F/ΔT - -4 - mV/°C IF=700mA

ΔλV

th j-c - 3.5 - °C/W IF=700mA

2 θ 1/2

- 130 -

Emission Angle

X direc-

tion

2 θ 1/2

Y direc-

- 130 -

tion

Notes:

2. Forward Voltage is measured with an accuracy of +/-0.1V.

3. Flux is measured with an accuracy of +/-15%.

4.

Wavelength :+/-0.1nm.

Test Item

Test Condition

Moisture-proof Test 85°C , 85%RH for 1000 hours

°

°

F=700mA

F=700mA

F=700mA

I

F=700mA

I

F=700mA

SPEC NO: DSAI8687 REV NO: V.1 DATE: NOV/14/2008 PAGE: 3 OF 8
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP:1209000079