Kingbright AP 1608 EC Service Manual

www.DataSheet4U.com

1.6X0.8mm SMD CHIP LED LAMP

AP1608EC HIGH EFFICIENCY RED

Features



1.6mmX0.8mm SMT LED, 1.1mm THICKNESS.



LOW POWER CONSUMPTION.



WIDE VIEWING ANGLE.



IDEAL FOR BACKLIGHT AND INDICATOR.



VARIOUS COLORS AND LENS TYPES AVAILABLE.



PACKAGE: 2000PCS / REEL.



RoHS COMPLIANT.

Package Dimensions

Description

The High Efficiency Red source color devices are made with
Gallium Arsenide Phosphide on Gallium Phosphide Orange
Light Emitting Diode.

Notes:

1. All dimensions are in millimeters (inches).

2. Tolerance is ±0.1(0.004") unless otherwise noted.

3.Specifications are subject to change without notice.

SPEC NO: DSAD0915 REV NO: V.4 DATE: MAR/14/2005 PAGE: 1 OF 4
APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1203000003

Selection Guide

Viewing

Iv (mcd)

Part No. Dice Lens Type

AP1608EC

Note:

1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.

HIGH EFFICIENCY RED (GaAsP/GaP)

WATER CLEAR 4 12

@ 20mA

Min. Typ.

Electrical / Optical Characteristics at TA=25°C

Symbol Parameter Device Typ. Max. Test ConditionsUnits

λpeak

λD

∆λ1/2

C Capacitance High Efficiency Red 15 pF VF=0V;f=1MHz

VF Forward Voltage High Efficiency Red 2.0 2.5 V IF=20mA

IR Reverse Current High Efficiency Red 10 uA VR = 5V

Peak Wavelength High Efficiency Red 627 nm IF=20mA

Dominant Wavelength High Efficiency Red 625 nm IF=20mA

Spectral Line Half-width High Efficiency Red 45 nm IF=20mA

Angle

2θθθθ1/2

120°

Absolute Maximum Ratings at T

Parameter High Efficiency Red Units

Power dissipation 105 mW
DC Forward Current 30 mA
Peak Forward Current [1] 160 mA
Reverse Voltage 5 V

Operating/Storage Temperature -40°C To +85°C

Note:

1. 1/10 Duty Cycle, 0.1ms Pulse Width.

SPEC NO: DSAD0915 REV NO: V.4 DATE: MAR/14/2005 PAGE: 2 OF 4
APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1203000003

A=25°C

High Efficiency Red AP1608EC

SPEC NO: DSAD0915 REV NO: V.4 DATE: MAR/14/2005 PAGE: 3 OF 4
APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1203000003

AP1608EC

Recommended Soldering Pattern
(Units : mm)

Tape Specifications
(Units : mm)

If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength),
the typical accuracy of the sorting process is as follows:

1. Wavelength: +/-1nm

2. Luminous Intensity: +/-15%

3. Forward Voltage: +/-0.1V
Note: Accuracy may depend on the sorting parameters.

SPEC NO: DSAD0915 REV NO: V.4 DATE: MAR/14/2005 PAGE: 4 OF 4
APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1203000003