Page 1
5.0X6.0mm SURFACE MOUNT LED LAMP
PRELIMINARY SPEC
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
z SINGLE COLOR.
z SUITABLE FOR ALL SMT ASSEMBLY AND SOLDER
PROCESS.
z AVAILABLE ON TAPE AND REEL.
z IDEAL FOR BACKLIGHTING.
z PACKAGE : 500PCS / REEL.
zMOISTURE SENSITIVITY LEVEL : LEVEL 4.
zRoHS COMPLIANT.
Package Dimensions
Part N u mb e r : AA5060PBS/Z BLUE
Description
The Blue source color devices are made with InGaN Light
Emitting Diode.
Static electricity and surge damage the LEDS.
It is recommended to use a wrist band or anti-electrostatic
glove when handling the LEDs.
All devices, equipment and machinery must be electrically
grounded.
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Specifications are subject to change without notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAH4670 REV NO: V.1 DATE: MAY/28/2007 PAGE: 1 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.LIU ERP:1201003010
Page 2
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might leads to damage and premature failure of the LED.
1. Handle the component along the side surfaces by using forceps or appropriate tools.
2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
3. Do not stack together assembled PCBs containing exposed LEDs. Outside impact may scratch the silicone lens or
damage the internal circuitry.
4. During surface-mounting, the pickup capillary diameter should be larger than the silicone lens to insure the capillary
does not scratch or damage the lens.
SPEC NO: DSAH4670 REV NO: V.1 DATE: MAY/28/2007 PAGE: 2 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.LIU ERP:1201003010
Page 3
Selection Guide
V
Iv (mcd) [2]
Part No.
AA5060PBS/Z BLUE (InGaN) WATER CLEAR
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
2. Luminous Intensity / Luminous Flux: +/-15%.
Dice Lens Type
@ 20mA
Min. Typ.
280 480
Electrical / Optical Characteristics at TA=25°C
Symbol Parameter Device Typ. Max. Test Conditions Units
λpeak
λD [1]
Δλ1/2
C Capacitance Blue 110 pF VF=0V;f=1MHz
VF [2] Forward Voltage Blue 3.2 3.7 V IF=20mA
Peak Wavelength Blue 458 nm IF=20mA
Dominant Wavelength Blue 465 nm IF=20mA
Spectral Line Half-width Blue 22 nm IF=20mA
iewing
Angle [1]
2θ1/2
120°
IR Reverse Current Blue 10 uA VR = 5V
Notes:
1. Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
Absolute Maximum Ratings at T
Parameter Blue Units
Power dissipation 111 mW
DC Forward Current 30 mA
Peak Forward Current [1] 100 mA
Reverse Voltage 5 V
Operating / Storage Temperature -40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
A=25°C
SPEC NO: DSAH4670 REV NO: V.1 DATE: MAY/28/2007 PAGE: 3 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.LIU ERP:1201003010
Page 4
Blue AA5060PBS/Z
SPEC NO: DSAH4670 REV NO: V.1 DATE: MAY/28/2007 PAGE: 4 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.LIU ERP:1201003010
Page 5
AA5060PBS/Z
Recommended Soldering Pattern
(Units : mm; Tolerance: ±0.1)
Tape Specifications
(Units : mm)
SPEC NO: DSAH4670 REV NO: V.1 DATE: MAY/28/2007 PAGE: 5 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.LIU ERP:1201003010
Page 6
PACKING & LABEL SPECIFICATIONS AA5060PBS/Z
SPEC NO: DSAH4670 REV NO: V.1 DATE: MAY/28/2007 PAGE: 6 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.LIU ERP:1201003010
Loading...