UC1000 Universal Controller
KING Quest™ Satellite Antenna System
Makes the
compatible with
DIRECTV
®
DISH® Bell TV™
11200 Hampshire Avenue South, Bloomington, MN 55438
PH 952.922.6889 || FAX 952.922.8424 || kingconnect.com
®
Please read the
“BEFORE YOU START”
section on the inside of this cover
before using the UC1000 Controller.
! !
The antenna unit requires a direct line-ofsight to the satellites in the southern sky.
Any tall objects or objects too close to
the antenna can block the signal.
BEFORE YOU START
IMPORTANT! DISH CUSTOMERS ONLY!
If you have a DISH Wally® receiver, or a model ViP®211z, ViP211k, ViP211 or
411 single tuner HD receiver, you can use the simplied KING® Tailgater® user
interface on your receiver.
To do so, complete sections 1 and 2, and when you get to section 3
ANTENNA CONFIGURATION, choose Tailgater Mode.
DO NOT USE SECTIONS 4 AND 5. Instead, turn on your TV, receiver and
controller and follow the on-screen instructions.
Complete these ve sections to start watching TV!
CONNECTIONS
ALARM MODE
ANTENNA CONFIGURATION
RECEIVER CONFIGURATION
OPERATION
1
2
3
4
5
PLEASE READ ALL OF THE INFORMATION ON THIS PAGE
BEFORE USING YOUR UC1000 CONTROLLER.
! !
IMPORTANT!
Never use the UC1000 Controller in
combination with the power injector.
If your current KING Quest system uses a power injector,
remove and replace it with the UC1000 Controller.
CONNECTIONS
1
! !
This unit is shipped from the factory with the alarm feature in the ON mode. If
you wish to have the alarm in the ON mode, you can skip this section and go
to section 3. To disable the alarm, follow the instructions below.
ALARM MODE
2
Press and IMMEDIATELY RELEASE POWER to turn on
controller.
Wait for lights to stop ashing and COAX CONNECTION
light to stay on (about 10 seconds).
1
• Single Beep (beep...beep...beep) Alarm is OFF.
• Double Beep (beep beep...beep beep) Alarm is ON.
Simultaneously press and HOLD POWER and
SCAN until controller begins beeping.
2
Press and IMMEDIATELY RELEASE SCAN repeatedly to
toggle between the on and off modes.
Beep pattern will change to indicate new mode.
3
When alarm is in desired mode, press and HOLD SCAN until
COAX CONNECTION light stops ashing.
Controller saves alarm setting.
4
6
Go to section 3.
Press and HOLD POWER until controller turns off.
About 3 seconds.
5
ALARM OPERATION
If the coax cable is disconnected from the antenna unit or the controller while
the system is turned on or in standby mode, the controller will sound an alarm.
To turn off the alarm when it is sounding, press and HOLD POWER until the
controller turns off (about 3 seconds).
You can change the alarm mode at any time by following the steps on the
previous page.
The KING UC1000 Controller is factory preset for DISH HD and SD (satellites
110, 119 and 129).
If this is your desired service option, you do not need to congure your
antenna. Go to section 4.
If you wish to use a different DISH service option, or if you have DIRECTV or
Bell TV service, you will need to recongure the antenna as shown below.
Press and IMMEDIATELY RELEASE POWER to turn on
controller.
Wait for lights to stop ashing and COAX CONNECTION
light to stay on (about 10 seconds).
1
6
Press and HOLD SCAN until SCAN PROGRESS lights ash
(controller enters service mode).
About 10 seconds.
2
Press and IMMEDIATELY RELEASE SCAN repeatedly to
scroll thru service options.
Match up lights on controller to lights in chart on opposite
page for desired service.
3
Press and HOLD SCAN until SCAN PROGRESS lights turn
off (controller saves service setting).
About 3 seconds.
4
Go to section 4.
Press and HOLD POWER until controller turns off.
About 3 seconds.
5
ANTENNA CONFIGURATION
3
Loading...