2 Drawer
Vehicle Storage System
Part No 51000
Installation:
Includes:
Mounting Kit:
4 x bolts
4 x washers
4 x locking nuts
1
Remove right hand side top section
by undoing the 10 retaining screws
and set aside taking care not to loose
the fasteners and remove/open the
fridge slide by sliding outwards. This
allows access to the internal base of
the drawer system so it can be bolted
to the vehicle
2
Installation:
2
Remove the 2 drawers by
unlatching the 2 retaining latches
located at the rear interior of each of the
drawers
3
Due to the heavy weight of this
product please ensure that you
have at least 1 person assist you in
lifting this product into the interior of the
vehicle. Also ensure that the drawers
and tops are removed to minimise
weight while installing into the vehicle
4
Check the base of the vehicle
that the drawer system is to be
installed in and identify suitable
mounting points within the vehicle.
Either use existing vehicle mounting
points or new drill new mount points
using the bottom fixing ribs as a guide
for drilling the holes or locating to
existing mounting points.
WARNING: Care must be taken when
drilling new holes into your vehicle.
Ensure that you avoid fuel and brake lines,
electrical wires and other components that
may damage your vehicle
NOTE: The mounting points on the ribs are
elongated and the ribs are adjustable to assist
in locating suitable mounting points
NOTE: Automotive carpet may need to be
removed using a sharp knife to gain easier
access to the vehicle mounting points or for
drilling holes
NOTE: Use a minimum of 4 mounting bolts
provided to ensure maximum mounting
strength and weight capacity are achieved.
3
Installation:
6
Once the mounting bolts are
secure refit or close the fridge
slide, re attach the right-hand top
section and trim ensuring all fasteners
are tightened.
5
Use the existing removed vehicle
bolts to secure the frame base
via mounting slots provided OR the
mounting bolts provided to secure to the
vehicle. Ensure the bolts as securely
tightened and use a suitable thread glue
to ensure they do not loosen.
7
Refit both drawers ensuring
that rear locating stops
automatically engage.
NOTE: A firm push is required to move the
drawers past the automatic drawer stops.
4
Care and Maintenance:
ENSURE:
• Ensure all extremities are clear
of moving parts especially when
opening and closing the drawers
and fridge slide
• Distribute weight evenly when
loading the drawer system in
both the drawers and top sections
• Ensure all items stored on top of
the drawer system are secured
using the anchor points and
suitable tie downs
• For optimum safety install a
quality cargo barrier
• Ensure the product is regularly
maintained and cleaned to
optimise the products life span
• Ensure drawers are locked at
all times to protect contents
AVOID:
• Do not overload the fridge slide
weight capacity (Keep below 85kgs)
• Do not overload the drawers
(keep below 100kgs)
• Do not open both the fridge slide
and drawers at the same time
as this may cause product
instability
• Do not use chemicals, solvents,
when cleaning the carpet. Use
warm soapy water and vacuum
regularly
• Do put place sharp objects on
the carpeted areas as this my
damage the surface
• Metal surfaces inside vehicles
will become extremely hot.
Avoid touching metal surfaces
until they cool down
5
WARNING: Product is designed for interior use only
Care and Maintenance:
Maintenance:
• Remove both drawers using the
internal rear latches and inspect
and clean all roller bearings
using a clean cloth or rag
• Replace seized, rough, loose
roller bearings
• Clean drawer runners and lubricate
using a good quality light grease
(small amount only)
• Clean carpet by regularly
vacuuming . Use a damp cloth
and warm soapy water to clean
dirt and marks
• Use a quality stainless steel
cleaner on body sides
• Use a quality metal polish on
metal trim (remove prior to
cleaning to avoid marking the
carpet)
• Use Graphite powder or silicone
spray for lock barrels
• Use light grease on lock latch
and light oil on lock handle
6
• Regularly check and tighten all
all fasteners including mounting
points
Spare Parts:
7
1
20
6
Part No Description
13 51000-13 Fridge slide knob
14 51000-14 Fridge slide lock
15 51000-15 Fridge slide
16 51000-16 Ply wood Top (RHS)
17 51000-17 Drawer front
18 51000-18 Rear drawer latch x 1 (with screws)
19 51000-19 Rear panel
20 51000-20 Drawer (LHS)
21 51000-21 Drawer (RHS)
22 51000-22 Base cross beam mounting brackets x 4
23 51000-23 Rubber stopper
Part No Description
1 51000-1 Lock & Key
2 51000-2 Pull handle latch 1 pce (stainless steel)
3 51000-3 Roller bearing 1 pce
4 51000-4 Fridge slide handle
5 51000-5 Spare carpet (1X1M)
6 51000-6 Retractable tip down point x1 (with fasteners)
7 51000-7 Corner Trims (front)
8 51000-8 Corner Trim (side)
9 51000-9 Mounting bolt kit
10 51000-10 Hex key kit x 8
11 51000-11 Screw kit x 24
12 51000-12 Stainless side panels 2pce (right & left)
2
3
17
22
21
7
12
8
9
11
10
16
19
5
23
15
4
13
14
18
20
Dimensions:
8
Weight: 75Kg
Loading...