KIDZTECH TOYS 8419118 24GTX User Manual

NO.: 84191

Contents

-RC Vehicle (Vehicle) x 1

-RC Transmitter (Transmitter ) x 1

-Water container x1

-Drifting wheels x4

-Screwdriver x1

-Instruction Manual x 1

-6.4V Rechargeable Battery Pack x 1

-Charger x 1

-9V Battery x 1

1. The 6.4V Lithium Rechargeable Battery Pack must be charged before use by
utilizing the battery charger which included

2. Do not overcharge the battery pack. Do not charge for more than 6 hours

3. Do not charge the battery pack if it shows leakage, corrosion, or has loose or

exposed wires or other damage

4. Do not cover the battery pack with any sort of materials while charging

5. Do not touch the battery pack when it is hot. Wait until the battery pack cools

before installing it in the Vehicle and before recharging

6. Do not dispose of the battery in fire

7. Do not dismantle the battery or charger, and do not cut the battery or charger

cables

8. The battery pack will be warm after charging, and hot after use in a vehicle

9. The supply terminals are not to be short-circuited

10. Rechargeable batteries are to be removed from the toy before being charged

11. Rechargeable batteries are only to be charged by adult.

12. Battery replacement must be only made by adults

13. The transformer (charger) is not a toy

14. Charge only type (1300mAh Max.) rechargeable battery packs. Other types of
batteries may burst causing injury to persons and damage. This power unit is
intended to be correctly orientated in a vertical or floor mount position. This
charger is intended to be used for charging 6.4V lithium rechargeable battery
pack with capacity 1300mAh Max. It cannot be used for charging
non-rechargeable batteries. Regular examination of battery charger for any
damage to their cord, plug, enclosure and other parts, and that, in the event
of such damage, it must not be used with the charger or battery pack charge
until such damage has been repaired. Note that the 9V battery is
non-rechargeable and is not to be recharged. Only batteries of the same or
equivalent type as recommended are to be used. It will need replacement
when transmission is poor.

15. Exhausted batteries are to be removed from the product.

Battery Installation

For Transmitter (Fig. 3 and Fig. 4)

1. Unscrew the screw on the battery cover

2. Open the battery cover

3. Install 1 new 9V battery with correct polarity (+/-) as shown inside the battery
compartment

4. Close the battery cover

5. Tighten the screw on the battery cover

For Vehicle (Fig. 1 and Fig. 2)

1. Switch OFF the power

2. Unscrew the screw on the battery cover

3. Open the battery cover

4. Install 6.4V battery pack with correct polarities (+/-)
as shown inside the battery compartment

5. Close the battery cover

6. Tighten the screw on the battery cover

Vehicle - Battery Installation

Vehicle

Transmitter

Transmitter - Battery Installation

41

41

ages

8

PRO. SYSTEM

1:14

SCALE

ADAPTER
(Included)

1 X 9V Battery
For Transmitter
(Included)

9V

6.4V
1300mAh
For Vehicle
(Included)

6.4V

RC Vehicle x 1

Water container x1

Screwdriver x1

Drifting wheels x4

RC Transmitter x 1

30M / 98FT
RANGE

Charging the Rechargeable Battery Pack for the Vehicle:

1. Connect the 6.4V lithium rechargeable battery pack to the battery charger

2. Plug the charger into the standard AC socket

3. The charging time for a full charge is about 3 hours

4. When charging is completed, unplug the charger from the AC socket

5. Disconnect the rechargeable battery pack form the battery charger

Fig. 1

Fig. 4

I

+

9 V

Battery

Fig. 3

LED Battery
Indicator

Steering
Wheel

ON/OFF
(At Rear)

Accelerator
Trigger

KIDZTECH TOYS

MADE IN CHINA

ON
OFF

L

R

Mustang GT4

Direction
Adjustment

Battery
Compartment

ON/OFF

Fig. 2

ON
OFF

L

R

6.4V

Mustang GT4

LIGHTING

EFFECT

84191

1. Turn on the Vehicle.

2. Keep pulling the trigger of the Transmitter forward then turn the Transmitter on. Do not release the trigger until the binding process completed.

3. The LED light of the Transmitter will keep flashing for the binding process, which is within 8 seconds. Do not turn off any buttons while in progress, otherwise,
the process will be terminated.

4. After the wheels of the Vehicle turn left and right and the LED light of the Transmitter stops flashing, the binding process completed for playing.

5. If it cannot complete within 8 seconds, please turn off both Vehicle and Transmitter and re-start the binding process.

6. When the binding process is done, whenever switching the Vehicle and Transmitter on and off, it searches for the code that it memorized, and will only lock on to
the Transmitter signal containing that code.

7. Please turn off both Vehicle and Transmitter and re-start all binding process if changing to another 2.4GHz Transmitter for playing.

How To Bind

How To Play

How To Fill In Water For Smoking Effect

4. Close the cap firmly. (Fig.8)

3. Fill in clear water to vehicle by using the provided
water container. (Fig.7)

2. Open the cap of water tank on the vehicle. (Fig.5 and Fig.6)

1. Fill in clear water into water container.

Water tank cap

Fig. 5

Fig. 7 Fig. 8

Fig. 6

3. Use the Accelerator Trigger to drive the Vehicle Forward, Stop and Backward

4. If the vehicle does not run in straight line, adjust the
Direction Adjustment on the Vehicle chassis

5. Play on smooth surface to have the optimum performance

6. Remember to switch OFF the power of the Vehicle and
Transmitter after playing

7. The optimum control range is up to 30m outdoor

1. Switch ON the Vehicle and Transmitter.

Turn Left Turn Right

2. Use the Steering Wheel to control the Vehicle turning left or right

ON

OFF

Vehicle

Forward

Stop

Backward

Transmitter