KIDZTECH TOYS 1009392 27MTX User Manual
STUNT CYCLE
6+
CONTENTS
1x Stunt Cycle
LED
Power Switch
(underneath)
1. Slide the power switch on the underside of the car to the ON position.
2. The remote will automatically connect to the car
3. Use the remote’s wheel to rotate the car’s rear wheel
4. Press the controller lever towards the controller to move the car go forward
5. Pull the controller lever away from the controller to move the car backwards
6. Ready, set, go!
Wheel
Trigger
1x Remote
PLAY
SAFETY PRECAUTIONS
• For indoor use only. Avoid water when operating.
• Do not use people or animals as obstacles.
• Never operate your vehicle on the street or highway
• Do not run car into furniture objects or hard surfaces as this will
cause damage to both the objects and car.
• Keep fingers, hair and loose clothing away from the tires, gears
and motor while car is switched to “ON’.
• Do not expose to extreme temperatures or moisture
• Do not leave car or transmitter near sources of heat or under
direct sunlight for long periods of time.
• Adult supervision is recommended when operating car.
• Thoroughly inspect products before every use. If the product
appears worn, frayed/splintered, cracked, or broken in any
manner, discontinue use and discard immediately.
BATTERY WARNING:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable
batteries.
• Alkaline batteries are recommended. Use only the specified
voltage.
• Insert batteries using the correct polarity. Always use, replace,
and recharge (if applicable) batteries under adult supervision.
• Do not charge with non-rechargeable batteries.
• Do not short-circuit the battery supply terminals.
• Do not dispose of batteries in a fire, batteries may explode or leak.
• Remove batteries before storing.
• Recycle or dispose of batteries according to federal, state, and
local laws.
• Keep these instructions for future reference.
BATTERY INSTALLATION
The car requires 4 “AA” 1.5V battery (not included) and the remote requires 2 “AAA” 1.5V batteries
(not included).
Use a Phillips head or Cross screwdriver to loosen the screw securing the corresponding battery
cover plate. Insert the batterie(s), ensuring the correct polarity per the diagrams below. Replace
the battery cover and tighten the screw.
OFF
WARNING:
CHOKING HAZARD - Small parts.
Not for children under 3 years.
WARNING: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
— Consult the dealer or an experienced radio/ TV technician for help.
KEEP THIS INSTRUCTION MANUAL AS IT CONTAINS IMPORTANT
INFORMATION FOR FUTURE REFERENCE.
Due to continuous product improvements, the pictures on this manual may
dier slightly from the actual product.
©2019 MerchSource, LLC. Irvine, CA 92618. All rights reserved.
Printed in China
FOR TECHNICAL SUPPORT,
PLEASE CALL
1-800-374-2744
Loading...