KidKraft Cedar Summit Lookout Extreme, Cedar Summit F25745 Installation And Operating Instructions Manual

F25745 Lookout Extreme

Safety Zone

LOOKOUT

EXTREME

PLAYSET

F25745

INSTALLATION AND OPERATING INSTRUCTIONS

32' 4"

989cm

9.89 m

19' 4"

589cm

5.89 m

12' 8"

386cm

3.86 m

WARNING

Manufacturer contact informaon provided below.

OBSTACLE FREE SAFETY ZONE - 32’ 4” x 27’11” (9.89 x 8.5 m) area requires Protecve Surfacing. See page 3.

27' 11"

850cm

MAXIMUM VERTICAL FALL HEIGHT - 6’ 7” (2.01 m)

8.5 m

CAPACITY - 16 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.

RESIDENTIAL HOME USE ONLY. Not intended for public areas such as mul-unit residences, schools, churches, nurseries, day cares or parks. Warning. Only for domesc use.

To reduce the risk of serious injury or death, you must read and

follow these instrucons. Keep and refer to these instrucons oen and give them to any future owner of this play set.

10 - 12 Hrs

1 - 2 Hrs

2-4 Hrs

FOR FORT & SWING

TUBE SLIDE

TWO PERSON

ASSEMBLY

For Outdoor Family Domestic Use Only

Cedar Summit by KidKraft 4630 Olin Road Dallas, TX 75244, United States

customersupport@kidkraft.com Online Parts Replacement: Cedarsummitplay.com/parts-center-warranty-claim Customer Service: 1(800) 933-0771 or (972) 385-0100

KidKraft Netherlands BV Olympisch Stadion 29 1076DE Amsterdam, The Netherlands

Europe Customer Service: +31 (0)20 305 8620

europecustomerservice@kidkraft.com EU Online Parts Replacement: parts.kidkraft.eu

14 - 18 Hrs

FOR FORT & SWING

TWO PERSON

ASSEMBLY

Table of Contents

Warnings and Safe Play Instructions ..........pg. 2

Protective Surfacing Guidelines. . . . . . . . . . . . . . . pg. 3

Instructions for Proper Maintenance .........pg. 4

About Our Wood – Limited Warranty .........pg. 5

Keys to Assembly Success ....................pg. 6

Part ID ......................................pg. 10

Step-By-Step Instructions ...................pg. 19

Installation of I.D./Warning Plaque ......Final Step

Rev 12/10/20189405745

Warnings and Safe Play Instructions

CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred

while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system. Go over the wa understand and follow them. Remember on-site adult supervision is required for children of all ages.

rnings and safe play instructions regularly with your children and make certain that they

WARNING

SERIOUS HEAD INJURY HAZARD

Installation over concrete, asphalt, dirt, grass, carpet and other hard surface creates a risk of serious injury or death from falls to the ground. Install and maintain shock absorbing material under and around play-set as recommended on page 3 of these instructions.

COLLISION HAZARD

Place play-set on level ground at least 2m from any obstruction such as a garage or house, fences, poles, trees, sidewalks, walls, landscape ti pavement, planters, garden borders, overhanging branches, laundry lines, and electrical wires. (See OBSTAC

CHOKING HAZARD/SHARP EDGES & POINTS

Adult assembly required. This product contains small parts and parts with sharp edges and points. Keep parts away from children until fully assembled.

WARNING LABEL

Owners shall be responsible for maintaining the legibility o

LE FREE SAFETY ZONE on cover)

f the warning labels.

mbers, rocks,

STRANGULATION HAZARD

,senilsehtolc ,sepor htiw yalp ot nerdlihc wolla REVEN • pet leashes, cables, chains or cord-like items when using this play-set or to attach these items to play-set.

ponchos, hoods, scarves, capes, necklaces, items with draw-strings, cords or ties when using this play-set.

stemleh trops ro ekib raew ot nerdlihc wolla REVEN •

when using this play-set.

Failure to prohibit these items, even helmets with chin straps, increases the risk of serious injury and death to children from entanglement and strangulation.

TIP OVER HAZARD

Choose a level location for the equipment. This can reduce the likelihood of the p surfacing materials washing away during heavy rains.

O NOT allow children to play on the play-set until the

assembly is complete and the unit is properly anchored.

Never add extra length to chain or rope. The chains or ropes provided are the maximum length designed for the swinging element(s)

lay set tipping over and loose-ﬁll

WARNING

front cover.

footwear.

of the swing seat to prevent erratic swing motion or falling off.

loose, or sharp edged hardware. Replace, tighten and or sand smooth as required prior to playing.

or cable are secured at both ends and cannot be looped back on itself as to create an entanglement hazard.

plastic rides to assure that they are not very hot as to cause burns. Cool hot slide and rides with water and wipe dry prior to using.

Orientate slide such that it gets the least amount of exposure to the sun.

– Safe Play Instructions

eeS .tes-yalp ruoy fo snoitatimil yticapac evresbO

gnisolcne toof lluf dna gnittﬁ llew htiw nerdlihc sserD

retnec eht ni thgiew lluf rieht htiw tis ot nerdlihc hcaeT

,gnissim ;doow dekcarc ro nekorb ,deretnilps rof kcehC

rehto dna edils eht kcehc ,syad toh ro dna ynnus nO

raewtoof leeh ro eot nepo raew ot nerdlihc wolla ton oD

like sandals, ﬂip–ﬂops or clogs.

dniheb ,neewteb ,tnorf ni ,klaw ot nerdlihc wolla ton oD

or close to moving rides.

pool ro sepor ro sniahc gniws tsiwt nerdlihc tel ton oD them over the top support bar. This may reduce the strength of the chain or rope and cause premature failure.

.noitom ni era yeht elihw sedir ffo teg nerdlihc tel ton oD

.tew si ti nehw tnempiuqe no gnibmilc timrep ton oD

niahc ,sreddal epor ,sepor gnibmilc dednepsus taht yfireV

manner for which it was not intended. Standing on or jumping from the roof, elevated platforms, swings, climbers, ladders or slide can be dangerous.

run up slide.

a ni tnempiuqe fo esu ro yalp hguor timrep ton oD

.staes ro sedir ytpme gniws ot nerdlihc wolla ton oD

ro tsrﬁ daeh edils nwod og ot nerdlihc wolla ton oD

2 europecustomerservice@kidkraft.com

Protective Surfacing - Reducing Risk of Serious Head Injury From Falls.

One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever product you select, follow these guidelines:

Loose-Fill Materials

• Maintain a minimum depth of 9 inches of loose-ﬁll materials such as wood mulch/chips, engineered wood ﬁber (EWF), or shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet high. NOTE: An initial ﬁll level of 12 inches will compress to about a 9-inch depth of surfacing over time. The surfacing will also compact, displace, and settle, and should be periodically raked and reﬁlled to maintain at least a 9-inch depth.

• Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)

NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play surface -- does not need any protective surfacing.

• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to account for water drainage.

• Periodically rake, check and maintain the depth of the loose-ﬁll surfacing material. Marking the correct depth on the play equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to rake and evenly redistribute the surfacing in heavily used areas.

• Do not install loose ﬁll surfacing over hard surfaces such as concrete or asphalt.

Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles

You may be interested in using surfacing other than loose-ﬁll materials - like rubber tiles or poured-in-place surfaces.

• Installations of these surfaces generally require a professional and are not “do-it yourself” projects.

• Review surface speciﬁcations before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that the product has been tested to the following safety standard: ASTM F1292 Standard Speciﬁcation for Impact Attenuation of Surfacing Materials within the Use Zone of Playground Equipment. This report should show the speciﬁc height for which the surface is intended to protect against serious head injury. This height should be equal to or greater than the fall height - vertical distance between a designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing below - of your play equipment.

• Check the protective surfacing frequently for wear.

Placement

Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;

• Extend surfacing at least 2m from the equipment in all directions.

• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar from which the swing is suspended.

• For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all directions.

2H 2H

Denotes Use Zone with Protective Surfacing

6 ft.

Use Zone for Single-Axis Swings

6 ft.

6 ft. 6 ft.

6 ft.

Denotes Use Zone with Protective Surfacing

Use Zone for Multi-Axis Swings

From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf

3 europecustomerservice@kidkraft.com

Instructions for Proper Maintenance

Your Cedar Summit Play System is designed and constructed of quality materials with your child’s safety in mind. As

with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your

Play Set, it is important that you, the owner, properly maintain it.

Check the following at the beginning of the play season:

HARDWARE:

Check metal parts for rust. If found,

sand and repaint using a non-lead paint

complying with 16 CFR 1303. Inspect and tighten all hardware. On wood assemblies DO NOT OVERTIGHTEN as to cause crushing and

splintering of wood. Check for sharp edges or protruding screw threads, add washers if required.

If Bolt protrudes

beyond T-Nut

Use an extra

flat washer

SHOCK ABSORBING SURFACING:

Check for foreign objects. Rake and check depth of loose

fill protective surfacing materials to prevent compaction and

maintain appropriate depth. Replace as necessary. (See Protective Surfacing, page 3)

GROUND STAKES (ANCHORS):

Check for looseness, damage or deterioration. Should firmly

anchor unit to ground during use. Re-secure and or replace,

if necessary.

SWING HANGERS:

Check that bolts are secure and tight. Quick clips should be

completely closed and threaded clips screwed tight.

If squeaking occurs lubricate bushings with oil or WD-40®.

SWINGS, ROPES AND RIDES:

Reinstall if removed during cold season. Check all moving

parts including swing seats, ropes, chains and attachments

for wear, rust and other deterioration. Replace as needed.

Check that ropes are tight, secure at both ends and cannot

loop back as to create an entrapment.

WOOD PARTS:

Check all wood members for deterioration, structural

damage and splintering. Sand down splinters and replace deteriorated wood members. As with all wood, some checking and small cracks in grain is normal.

Applying a water repellent or stain (water-based) on a yearly

basis is important maintenance to maintain maximum life and performance of the product.

Check twice a month during play season:

HARDWARE:

Inspect for tightness. Must be firmly against, but not

crushing the wood. DO NOT OVER-TIGHTEN.

This will cause splintering of wood.

Check for sharp edges or protruding screw threads.

Add washers if required.

SHOCK ABSORBING SURFACING:

Rake and check depth of loose fill protective surfacing

materials to prevent compaction and maintain appropriate

depth. Replace as necessary. (See Protective Surfacing, page 3)

Check once a month during play season:

SWING HANGERS:

Check that they are secure and orientated correctly. Hook

should rotate freely and perpendicular to support beam.

If squeaking occurs lubricate bushings with oil or WD-40®.

SWINGS AND RIDES:

Check swing seats, all ropes, chains and attachments for

fraying, wear, excessive corrosion or damage.

Replace if structurally damaged or deteriorated.

Check at the end of the play season:

SWINGS AND RIDES:

To prolong their life, remove swings and store inside when

outside temperature is below 32°F/0°C. Below freezing,

plastic parts may become more brittle.

If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable

hazards at the time it is discarded. Be sure to follow your local waste ordinances.

SHOCK ABSORBING SURFACING:

Rake and check depth of loose fill protective surfacing

materials to prevent compaction and maintain appropriate

depth. Replace as necessary.

(See Protective Surfacing, page 3)

4 europecustomerservice@kidkraft.com

About Our Wood

Cedar Summit Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to

weathering which can change the appearance of your set.

What causes weathering? Does it affect the strength of my Play System?

One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is different than the interior of the wood. As the climate changes, moisture moves in or out of the wood, causing tension which can result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of the product:

1. Checking is surface cracks in the because the surface and interior moisture content will vary more widely than in thinner wood.

2. Warping results from any distortion (twisting, cupping) from the original plane of the board and often happens from rapid wetting and drying of the wood.

3. Fading happens as a natural change in the wood color as it is exposed to sun-light and will turn a grey over time.

How can I reduce the amount of weathering to my Play System?

At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, applying a water repellant or stain on a yearly basis is important mainten

Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.

warranty service.

wood along the grain. A post (4” x 4”) will experience more checking than a board (1” x 4”)

ance. (see your local stain and paint supplier for a recommended product)

10 Year Limited Warranty

Cedar Summit by KidKra warrants that this product is free from defect in materials and workmanship for a period of one year from the original date of purchase. In addition, lumber is warranted for 10 years against structural failure due to rot and insect damage. All other parts, such as hardware, swings, rides, accessories, and slides carry a one-year warranty only. This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance is required to assure the integrity of your Play System. Failure by the owner to maintain the product according to the maintenance requirements may void this warranty. This warranty does not cover any inspection cost.

This Limited Warranty does not cover:

• Labour for replacement of any defective item(s);

• Incidental or consequential damages;

• Cosmetic defects which do not affect performance or integrity;

• Vandalism; improper use or installation; acts of nature;

• Minor twisting, warping, checking, or any other natural occurring properties of wood that do not affect performance or integrity.

Cedar Summit by KidKraft products have been designed for safety and quality. Any modifications made to the original product could damage the structural integrity of the unit leading to failure possible injury. Cedar Summit by KidKraft cannot assume any responsibility for modified products. Furthermore, modification voids any and all warranties.

This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a Cedar Summit by KidKra Play System be used in public settings such as schools, churches, playgrounds, parks, day cares and the like. Such use may lead to product failure and potential injury. Any and all public use will void this warranty. Cedar Summit by KidKraft disclaims all other representations and warranties of any kind, express or implied

and

province to province. This warranty excludes all consequential damages, however, some states do not allow the limitation or exclusion of consequential damages, and therefore this limitation may not apply to you.

5 europecustomerservice@kidkraft.com

Tools Required

Keys to Assembly Success

• Tape Measure

• Carpenters Level

• Carpenters Square

• Claw Hammer

• Standard or Cordless Drill

Part Identification Key

On each page, you will find the parts and quantities required to complete the assembly step illustrated on that page. Here is a sample.

• #1 Phillips, #2 Robertson

and Screwdriver

• Ratchet with extension (1/2” & 9/16” sockets)

• Open End Wrench (1/2” & 9/16”)

• Adjustable Wrench

• 1/8” & 3/16” Drill Bits

2X 012 Post 2 x 4 x 83”

Quantity Key Number

Part Description, Part Size

• 3/16” Hex Key

• 8’ Step Ladder

• Safety Glasses

• Adult Helpers

• Pencil

Key Number: The first two digits represent the step number. The third digit represents the piece. Note that if the part is used in multiple steps then the number only reflects the first step it is used in.

Symbols

Throughout these instructions symbols are provided as important reminders for proper and safe assembly.

This identifies information that requires special

attention. Improper assembly could lead to an unsafe

or dangerous condition.

Use

Help

Measure

Distance

Use

Help

Check that assembly is square before tightening bolts.

Use a measuring tape to assure proper location.

Where this is shown, 2 or 3 people

are required to safely complete the step. To avoid injury or damage to the assembly make sure to get help!

Square

Assembly

Check that set or assembly is properly level before proceeding.

Pre-drill 1/8” & 3/16” Bit

Pre-drill a pilot hole

before fastening screw or lag to prevent splitting of wood.

This indicates time to tighten bolts, but

not too tight! Do not crush the wood.

This may create splinters and cause structural damage.

Use

Level

Tighten

Bolts

CAUTION – Protrusion Hazard

Once the assembly is tightened, watch for exposed threads. If a thread protrudes from the T-Nut, remove the bolt and add washers to eliminate this condition.

Extra washers have been provided for this purpose.

Proper Hardware Assembly

Lag screws require drilling pilot holes to avoid splitting wood. Only a flat washer is required. For ease of installation liquid soap can be used on all lag-type screws.

For bolts, tap T-Nut into hole with

hammer. Insert the hex bolt through

lock washer first then flat washer then hole. Because the assemblies need to be squared do not completely tighten

until instructed. Pay close attention to diameter of the bolts. 5/16” is slightly larger than 1/4”.

Note: Wafer head bolts with blue lock

tight or a bolt with a Ny-Lok nut do NOT require a lock washer.

Lag Screw

Hex Bolt

Lock

Washer

Flat

Washer

No Yes

If Bolt protrudes

beyond T-Nut

Use an extra

flat washer

Lag Assembly

Before mounting Lag Screw, use factory drilled

holes as guides to drill 1/8”

pilot holes

Flat Washer

Bolt Assembly

T-Nut

(Hammer into place) Do not crush wood!

6 europecustomerservice@kidkraft.com

Your Key To Quick Assembly

SORTING WOOD PARTS INTO

EACH ASSEMBLY STEP WILL

SAVE TIME!

Step Step Step

SAVE TIME - TIP #1:

Wood parts are found in Box 2, 3, 4 & 5. Open each box with wood parts and look for the Key Number stamped on the end of the wood part (see chart below). Sort each wood part into the different assembly steps.

2X 012 Post 2 x 4 x 83”

Part Quantity Key Number

Step Number

(This is Step 1)

01 2

Order Listed

(The order the part is

SAVE TIME - TIP #2:

In addition to the key number stamp, you can also identify the wood parts by

using the Parts Identication pages in the manual or the Parts Identication

weather resistant poster.

Part Description Part Size

Key Number: The rst two digits represent the step

number. The third digit represents the order in which the part is listed in the step.

listed in step 1)

Note that if the part is used in multiple steps then

the key number only reects the rst step it is used in.

HARDWARE:

The majority of each hardware part comes packed in a separate bag so you do not need to sort the hardware. Each assembly step indicates which hardware (bolt, screw, washer etc.) you will require to complete the step.

7 europecustomerservice@kidkraft.com

Fruit & Basket

Front Roof Panel FSC

(hidden) x2

Steering Wheel

Maze N Wave Double Slide Yellow

Sign

Utensil Shelf x2

BBQ Lid

Bell

Sink

BBQ Base

BBQ Utensils

Cooktop

Panel Front Wall FSC

Narrow Front Panel FSC

Door Window Panel FSC

Door Hardware

Climbing Rope

SL Panel FSC

Rocks (10Pk)

Telescope w/ Mount

TNR 3 Short Exit

TNR3 Extended Lt Flange

TNR3 Extended Rt Flange

FRONT

8 europecustomerservice@kidkraft.com

Flat Panel Bracket Set (4Pk)

9x TNR 2 Slide Elbow

Nest End Panel FSC

TNR 2 Slide Exit Top

TNR 4 Clamp Ring Set (10Pk)

TNR Post Mount

Chalkboard Flag

Grips x3

Steel Hand

TNR Long

Tube Support

(hidden)

Back Panel Narrow FSC

Rope Ladder

EN71 Hand Rail

(hidden)

Bracket (3Pk)

Narrow Angle

Back Roof Panel FSC

BACK

20" Chain x2

Heavy Flat Bracket x2

2x Mod 5 Pane Window (2Pk)

Plastic Formed

Washers (18Pk)

Spring Loaded

DX Hanger (6Pk)

Quick Links x6

Heavy "C" Bracket

Plaque

KK Playset

Heavy "L" Bracket x3

Acro Bar

Acro Handle x2

48" Chain

(hidden)

Flat Bracket (2Pk)

Corner Bracket (9Pk)

Belt Swing x2

Panel Corner Bracket (8Pk)

Wall Back Panel FSC

Swing Wall Panel FSC

Stake (6Pk)

Rebar Ground

9 europecustomerservice@kidkraft.com

Part Identification (Reduced Part Size)

1pc.

15.9 x 76.2 x 436.5mm - Rope Support FSC - Box 2 - 4819262

572

5/8 x 3 x 17-3/16"

2pc.

15.9 x 82.6 x 254.5mm - Nest Floor Board G FSC - Box 2 - 4819227

471

5/8 x 3-1/4 x 10"

2pc.

15.9 x 82.6 x 312.9mm - Nest Floor Board F FSC - Box 3 - 4819226

477

5/8 x 3-1/4 x 10"

2pc.

15.9 x 82.6 x 482.6mm - Nest Ladder Gap FSC - Box 2 - 4819234

034

5/8 x 3-1/4 x 19"

1pc.

15.9 x 82.6 x 1060.5 mm - Access Rope Ladder Gap FSC - Box 2 - 4819286

026

1pc.

15.9 x 82.6 x 1060.5 mm - RW-AL Support FSC - Box 2 - 4819263

025

1pc.

15.9 x 82.6 x 1376mm - Narrow Wall B FSC - Box 2 - 4819215

561

5/8 x 3-1/4 x 41-3/4"

5/8 x 3-1/4 x 54-11/64"

1pc.

15pc.

1pc.

2pc.

15.9 x 85.7 x 285.8mm - Bell Top RT FSC - Box 2 - 4019101

193

5/8 x 3-3/8 x 11-1/4"

15.9 x 85.7 x 285.8 mm - Bell Top FSC - Box 2 - 4019102

191

5/8 x 3-3/8 x 11-1/4"

15.9 x 85.7 x 398.5mm - Short Floor Gap FSC - Box 2 - 4819264

541

5/8 x 3-3/8 x 15-11/16"

15.9 x 85.7 x 398.5mm - Short Floor FSC - Box 3 - 4819265

542

5/8 x 3-3/8 x 15-11/16"

15.9 x 85.7 x 812.8mm - Nest Wall Rails FSC - Box 2 - 4819245

611

15.9 x 85.7 x 904.9mm - Floor Board FSC - Box 2 - 4819050

123

15.9 x 108 x 388.4mm - Nest Floor Board E FSC - Box 3 - 4819225

476

5/8 x 3-1/4 x 15-19/64"

5/8 x 3-3/8 x 32"

5/8 x 3-3/8 x 35-5/8"

2pc.

1pc.

10 europecustomerservice@kidkraft.com

15.9 x 108 x 463.9mm - Nest Floor Board D FSC - Box 2 - 4819224

475

5/8 x 3-1/4 x 18-1/4"

15.9 x 108 x 1447.8mm - Rock Wall D FSC - Box 2 - 4819249

573

15.9 x 108 x 1447.8mm - Rock Wall E FSC - Box 2 - 4819250

574

5/8 x 4-1/4 x 57"

Part Identification (Reduced Part Size)

1pc.

15.9 x 108 x 1447.8mm - Rock Wall F FSC - Box 2 - 4819251

575

1pc.

15.9 x 108 x 1447.8mm - Rock Wall G FSC - Box 2 - 4819252

576

2pc.

15.9 x 114.3 x 543.6mm - Nest Floor Board C FSC - Box 3 - 4819223

474

5/8 x 4-1/2 x 21-13/32"

2pc.

15.9 x 114.3 x 623.3mm - Nest Floor Board B FSC - Box 3 - 4819222

473

5/8 x 4-1/2 x 24-17/32"

2pc.

15.9 x 114.3 x 703mm - Nest Floor Board A FSC - Box 2 - 4819221

472

5/8 x 4-1/2 x 27-43/64"

16pc.

15.9 x 114.3 x 904.9mm - Floor Board FSC - Box 2 - 4819051

121

5/8 x 4-1/4 x 57"

1pc.

1pc. -

1pc.

2pc.

15.9 x 133.4 x 1424.8mm - Rock Wall B FSC - Box 2 - 4819247

571

23.8 x 57.2 x 838.2mm - End Wall Top FSC - Box 3 - 4819287

662

- 23.8 x 57.2 x 850.9mm - SW Wall Top FSC - Box 3 - 4819071

131

23.8 x 57.2 x 990.6mm - Half Wall Top FSC - Box 2 - 4819131

132

23.8 x 60.3 x 308.1mm - Nest Center Joist FSC - Box 2 - 4819233

101

15/16 x 2-3/8 x 12-1/8"

23.8 x 76.2 x 204.6mm - Barrier Bottom D FSC - Box 2 - 4819204

592

15/16 x 3 x 8-3/64"

23.8 x 76.2 x 204.6mm - Barrier Top D FSC - Box 2 - 4819209

582

15/16 x 3 x 8-3/64"

23.8 x 76.2 x 435mm - Short Wall Tie FSC - Box 3 - 4819266

521

5/8 x 4-1/2 x 35-5/8"

5/8 x 5-1/4 x 56-1/16"

15/16 x 2-1/4 x 33"

15/16 x 2-3/8 x 33-1/2"

15/16 x 2-3/8 x 39"

15/16 x 3 x 17-1/8"

2pc.

23.8 x 76.2 x 489mm - Wall Tie FSC - Box 3 - 4819117

275

15/16 x 3 x 19-1/4"

1pc.

23.8 x 76.2 x 520mm - Barrier Top E FSC - Box 2 - 4819210

584

15/16 x 3 x 20-15/32"

1pc.

23.8 x 76.2 x 526.4mm - Barrier Top A FSC - Box 2 - 4819206

585

15/16 x 3 x 20-23/32"

11 europecustomerservice@kidkraft.com

Part Identification (Reduced Part Size)

1pc.

1pc. -

3pc.

23.8 x 76.2 x 539.8mm - Barrier Bottom A FSC - Box 2 - 4819201

595

15/16 x 3 x 21-1/4"

23.8 x 76.2 x 539.8mm - Barrier Bottom E FSC - Box 2 - 4819205

594

15/16 x 3 x 21-1/4"

23.8 x 76.2 x 746.9mm - Barrier Bottom B FSC - Box 3 - 4819202

593

15/16 x 3 x 29-13/32"

23.8 x 76.2 x 746.9mm - Barrier Top B FSC - Box 2 - 4819207

583

15/16 x 3 x 29-13/32"

23.8 x 76.2 x 895.4mm - Barrier Bottom C FSC - Box 2 - 4819203

591

23.8 x 76.6 x 895.4 mm - Barrier Top C FSC - Box 2 - 4819208

581

- 23.8 x 82.6 x 362 mm - SW Ground FSC - Box 3 - 4812606

141

15/16 x 3-1/4 x 14-1/4"

23.8 x 82.6 x 444.5mm - Nest Tread FSC - Box 3 - 4819243

033

15/16 x 3-1/4 x 17-1/2"

15/16 x 3 x 35-1/4"

4pc. -

1pc.

4pc.

1pc.

- 23.8 x 82.6 x 495.3 mm - Tread FSC - Box 3 - 4818957

023

15/16 x 3-1/4 x 19-1/2"

23.8 x 82.6 x 601.7mm - Support Diagonal FSC - Box 3 - 4819269

151

15/16 x 3-1/4 x 23-11/16"

23.8 x 108 x 1086.5mm - Table Top FSC - Box 2 - 4819324

182

25.4 x 31.8 x 659.6mm - Narrow Short Wall FSC - Box 2 - 4819213

531

25.4 x 31.8 x 812.8mm - Narrow Wall Rail FSC - Box 2 - 4819218

601

25.4 x 60.3 x 865mm - Back Wall Tie FSC - Box 3 - 4819303

043

25.4 x 60.3 x 865mm - Front Wall Tie FSC - Box 3 - 4819302

042

25.4 x 63.5 x 254mm - Door Stop FSC - Box 3 - 4812715

172

1 x 2-1/2 x 10"

31.8 x 57.2 x 809.6mm - Roof Gable Support FSC - Box 3 - 4819259

501

1 x 1-1/4 x 25-31/32"

1 x 1-1/4 x 32"

1-1/4 x 2-1/4 x 31-7/8"

15/16 x 4-1/4 x 42-3/4"

1 x 2-3/8 x 34-1/16”

4pc. -

1pc.

12 europecustomerservice@kidkraft.com

- 31.8 x 57.2 x 838.20mm - Roof Support FSC - Box 3 - 4609105

251

31.8 x 57.2 x1340.3mm - Narrow Wall D FSC - Box 2 - 4819217

062

31.8 x 57.2 x 1340.3mm - Rock Wall I FSC - Box 2 - 4819254

052

1-1/4 x 2-1/4 x 33"

1-1/4 x 2-1/4 x 52-49/64"

Part Identification (Reduced Part Size)

1pc.

31.8 x 57.2 x 1930mm - Rock Wall H FSC - Box 2 - 4819253

051

1pc.

31.8 x 57.2 x 2133.6mm - Rock Wall A FSC - Box 3 - 4819246

063

1pc.

31.8 x 57.2 x 2133.6mm - Narrow Wall A FSC - Box 2 - 4819214

057

1pc.

31.8 x 57.2 x 2336.8mm - Rock Wall C FSC - Box 2 - 4819248

058

1pc.

31.8 x 60.3 x 139.7mm - Ladder Joist Side FSC - Box 2 - 4819296

045

1-1/4 x 2-3/8 x 5-1/2"

2pc.

31.8 x 60.3 x 340.8mm - Roof Tie FSC - Box 2 - 4819260

621

1-1/4 x 2-3/8 x 13-13/32"

1pc.

31.8 x 60.3 x 374.7mm - Nest Side Joist FSC - Box 2 - 4819294

044

1-1/4 x 2-3/8 x 13-11/16"

1pc.

31.8 x 60.3 x 857.3mm - Nest Joist Mid FSC - Box 2 - 4819297

041

1-1/4 x 2-3/8 x 33-3/4"

2pc.

31.8 x 63.5 x 419.1mm - Swing Side Upright FSC - Box 3 - 4819112

282

1-1/4 x 2-1/2 x 16-1/2"

1-1/4 x 2-1/4 x 75-63/64"

1-1/4 x 2-1/4 x 84"

(reduced scale)

1-1/4 x 2-1/4 x 92"

1pc.

2pc.

1pc.

31.8 x 63.5 x 476.3 - Rope Bottom FSC - Box 3 - 4819200

027

1-1/4 x 2-1/2 x 18-3/4"

31.8 x 63.5 x 616mm - TNR Front Support FSC - Box 3 - 4819273

422

1-1/4 x 2-1/2 x 24-1/4"

31.8 x 63.5 x 1124mm - TB Support FSC - Box 2 - 4819114

271

31.8 x 76.2 x 138.7mm - Swing Top Small FSC - Box 3 - 4819270

321

1-1/4 x 3 x 5-15/32"

31.8 x 76.2 x 205.6mm - Narrow Wall Cross FSC - Box 2 - 4819220

064

1-1/4 x 3 x 8-3/32"

31.8 x 76.2 x 286.1mm - Narrow Wall Angled Cross FSC - Box 2 - 4819219

065

1-1/4 x 3 x 11-1/4"

31.8 x 76.2 x 349mm - Rock Wall Angle Cross FSC - Box 2 - 4819255

059

1-1/4 x 3 x 13-3/4"

31.8 x 76.2 x 378.3mm - SL Gusset FSC - Box 2 - 4819268

701

1-1/4 x 3 x 11-1/4"

1-1/4 x 2-1/2 x 44-1/4"

2pc.

31.8 x 76.2 x 419.1mm - Center Upright FSC - Box 3 - 4819106

274

1-1/4 x 3 x 16-1/2"

2pc.

31.8 x 76.2 x 419.1mm - Right Upright FSC - Box 3 - 4819110

272

1-1/4 x 3 x 16-1/2"

1pc. -

- 31.8 x 76.2 x 514.4mm - TNR Upright FSC - Box 2 - 4818965

761

1-1/4 x 3 x 20-1/4"

europecustomerservice@kidkraft.com

Part Identification (Reduced Part Size)

1pc. -

056

- 31.8 x 76.2 x 554mm - Rock Wall Bottom Cross FSC - Box 2 - 4819256

1-1/4 x 3 x 21-13/16"

1pc. -

055

- 31.8 x 76.2 x 554mm - Rock Wall Short Cross FSC - Box 2 - 4819258

1-1/4 x 3 x 21-13/16"

1pc. -

142

- 31.8 x 76.2 x 558.8mm - Diagonal FSC - Box 2 - 4812607

1-1/4 x 3 x 22"

1pc. -

432

- 31.8 x 76.2 x 617.5mm - SL Bottom A FSC - Box 3 - 4819288

1-1/4 x 3 x 24-5/16"

1pc. -

054

- 31.8 x 76.2 x 746.9mm - Rock Wall Floor Cross FSC - Box 3 - 4819257

1-1/4 x 3 x 29-13/32"

1pc. -

053

- 31.8 x 76.2 x 746.9mm - Rope Support Back FSC - Box 2 - 4819261

1-1/4 x 3 x 29-13/32"

2pc. -442 - 31.8 x 76.2 x 822.1mm - Nest Floor Joist C FSC - Box 2 - 4819230

1-1/4 x 2-3/8 x 13-11/16"

2pc. -511 - 31.8 x 76.2 x 844.6mm - Wall Post FSC - Box 2 - 4819284

1-1/4 x 2-3/8 x 13-11/16"

1pc. -762 - 31.8 x 76.2 x 997mm - TNR Ground Brace FSC - Box 2 - 4819274

1-1/4 x 3 x 39-1/4"

2pc. -

091

- 31.8 x 76.2 x 1035.1mm - Floor Joist FSC - Box 3 - 4812608

1pc. -281 - 31.8 x 76.2 x 1187.5mm - Swing Top FSC - Box 2 - 4819113

1pc. -

122

- 31.8 x 76.2 x 1606.6 - Long Floor Joist FSC - Box 3 - 4819056

1pc. -

451

- 31.8 x 82.6 x 222.3 - TNR Slide Block FSC - Box 3 - 4816005

1-1/4 x 3-1/4 x 8-3/4"

1pc. -

421

- 31.8 x 82.6 x 746.1 - TNR Floor Support FSC - Box 2 - 4819272

1-1/4 x 3-1/4 x 29-3/8"

2pc. -

411

- 31.8 x 82.6 x 1174.8 - Side Support FSC - Box 2 - 4819267

1pc. -

382

- 31.8 x 101.6 x 787.4 - Nest Wall Spacer FSC - Box 3 - 4819244

1-1/4 x 3 x 40-3/4"

1-1/4 x 3 x 46-3/4"

1-1/4 x 3 x 63-1/4"

1-1/4 x 3-1/4 x 46-1/4"

1-1/4 x 4 x 31"

1pc. -

431

- 31.8 x 102.2 x 617.5 - SL Bottom B FSC - Box 3 - 4819289

1-1/4 x 4 x 24-5/16"

2pc. -273 - 31.8 x 108 x 419.1mm - Left Upright FSC - Box 3 - 4819107

1-1/4 x 4-1/4 x 16-1/2"

14 europecustomerservice@kidkraft.com

Part Identification (Reduced Part Size)

1pc. -401 - 31.8 x 139.7 x 847.7mm - TNR Brace Support FSC - Box 2 - 4819271

1-1/4 x 5-1/2 x 33-3/8"

1pc. -032 - 34.9 x 63.5 x 1045.2mm - Nest Right Access FSC - Box 3 - 4819236

1pc. -031 - 34.9 x 63.5 x 1045.2mm - Nest Left Access FSC - Box 3 - 4819237

1pc. -

022

- 34.9 x 63.5 x 1468.8mm - Right Rail FSC - Box 3 - 4819240

1-3/8 x 2-1/2 x 41-1/8"

1pc. -021 - 34.9 x 63.5 x 1468.8mm - Left Rail FSC - Box 3 -

2pc. -

192

- 38.1 x 38.1 x 269.9mm - Bell Support FSC - Box 2 1-1/2 x 1-1/2 x 10-5/8"

1pc. -

441

- 38.1 x 38.1 x 749.3mm - Nest Floor Joist B FSC - Box 3 -

2pc. -

381

- 38.1 x 38.1 x 889mm - Nest Floor Joist A FSC - Box 3 -

1pc. -

181

- 38.1 x 38.1 x 1006.5mm - Table Support FSC - Box 3 - 4812612

2pc. -

291

- 38.1 x 38.1 x 1409.7 - Wall Support FSC - Box 1 - 4819118

2pc. -

092

- 38.1 x 38.1 x 1600 - Side Joist FSC - Box 1 - 4819064

1pc. -024 - 50.8 x 63.5 x 1468.8mm - Rope Rail FSC - Box 3 - 4819238

1pc. -

211

- 63.5 x 76.2 x 381 - SW Block Angle FSC - Box 3 -

2-1/2 x 3 x 15"

4819239

4609100

1-1/2 x 1-1/2 x 29-1/2"

4819228 1-1/2 x 1-1/2 x 35"

4819068

1-3/8 x 2-1/2 x 57-53/64"

4819229

1-1/2 x 1-1/2 x 39-5/8"

1-1/2 x 1-1/2 x 55-1/2"

1-1/2 x 1-1/2 x 63"

2 x 2-1/2 x 57-13/16"

1pc. -

212

- 63.5 x 76.2 x 381 SW Block FSC - Box 3 - 4818507

2-1/2 x 3 x 15"

1pc. -

202

- 76.2 x 76.2 x 406.4 - SW Mount FSC - Box 3 - 4819069

3 x 3 x 16"

1pc. -

221

- 63.5 x 76.2 x 1295.4 - Support Cross FSC - Box 1 - 4819067

2-1/2 x 3 x 51"

2pc. -

213

- 76.2 x 76.2 x 2336.8mm - SW Post FSC - Box 1 - 4819070

3 x 3 x 92"

1pc. -

201

- 76.2 x 133.4 x 2336.8 - Engineered SW Beam FSC - Box 1 - 4819049

15 europecustomerservice@kidkraft.com

3 x 5-1/4 x 92"

Part Identification (Reduced Part Size)

1pc. -

083

- 31.8 x 1092.2 x 2336.8mm

Wall Panel Back FSC - Box 2 - 47819194

1-1/4 x 43 x 92"

1pc. -

082

- 31.8 x 1092.2 x 2336.8mm

Panel Front Wall FSC - Box 2 - 47819135

1-1/4 x 43 x 92"

Narrow Front Panel FSC - Box 2 - 47819144

1pc. -

081

- 31.8 x 939.8 x 2336.8mm

SW Wall Panel FSC - Box 3 - 47819150

1-1/4 x 37 x 92"

1pc. -

073

- 31.8 x 546.1 x 2336.8mm

1-1/4 x 21-1/2 x 92"

1pc. -

071

- 31.8 x 939.8 x 2336.8mm

Nest End Panel FSC - Box 3 - 47819197

1-1/4 x 37 x 92"

1pc. -

072

- 31.8 x 546.1 x 2336.8mm

Back Panel Narrow FSC - Box 2 - 47819193

1-1/4 x 21-1/2 x 92"

16 europecustomerservice@kidkraft.com

Part Identification (Reduced Part Size)

1pc. -

661

- 34.9 x 514.4 x 847.8mm

SL Panel FSC - Box 2 - 47819196

1-3/8 x 20-1/4 x 33-1/8"

1pc. -

262

- 31.8 x 819.2 x 1143 mm

Back Roof Panel 1-1/4 x 32-1/4 x 45" FSC

Box 3 - 47609124

1-1/4 x 32-1/2 x 45"

1pc. -

171

- 31.8 x 400.1 x 1070mm

Door Window Panel FSC - Box 2 - 47602837

1-1/4 x 15-3/4 x 42-1/8"

1pc. -

261

- 30.2 x 926.6 x 1124 mm

Front Roof Panel 1-3/16 x 36-1/2 x 44-1/2" FSC

Box 3 - 47609082

1-1/4 x 32-1/4 x 45"

- TNR3 Short Exit (3310232)

- TNR 2 Slide Exit Top (3310224)

- TNR 3 Extended Flange Rt (3310231)

- TNR 3 Extended Flange Lt

(3310230)

- TNR 4 Clamp Ring Set (3300230) (10 Pk)

- TNR 2 Slide Elbow (3310221)

17 europecustomerservice@kidkraft.com

Hardware Identification

(5) LW2 - 5/16" Lock Washer - (51303300)

(Actual Size)

(34)

FW0 - 3/16" Flat Washer -

(51103100)

(9) FW6 - #12 Screw Bezel - (9299500)

(92)

LW1 - 1/4" Lock Washer - (51303200)

(67)

(18)

(7) LN3 -

(54)

1/4 Lock Nut

LN1

LN2

- 5/16" Lock Nut

3/8 Lock Nut

PB1 - Pan Bolt

- (54303200)

- (54303800)

1/4 x 3/4"

(54303300)

- (53453203)

(87)

FW1 - 1/4" Flat Washer - (51103200)

(82)

FW2 - 5/16" Flat Washer - (51103300)

(13)

FW10 - 3/8" Flat Washer - (51103800)

(100) S0

- Truss Screw

(60)

(40)

(34)

#8 x 7/8"

TN1

- 1/4" T - Nut

TN2

- 5/16" T- Nut

BN1

- 1/4" Barrel Nut

- (52933505)

(54503200)

(54503300)

(54803200)

(11)

PB6 - Pan Bolt

(34)

S37 - Pan Screw

(6)

S10 - Pan Screw

(33) S8

(40) S6

(31) S7

1pc.

- Pan Screw

S15

1/4 x 1"

#7 x 5/8"

#8 x 1"

#12 x 3/4"

#12 x 1"

#12 x 2"

-Flat Head Screw

- (53413210)

- (52433009)

- (52433510)

- (52433603)

- (52433610)

- (52433620)

#8 x 1 3/4" - (52042513)

(34)

PB2 - Pan Bolt

(9)

S38 - Pan Screw

(305)

S20 - Wood Screw

(136)

S11 - Wood Screw

(99) S3

(28) S4

- Wood Screw

1/4 x 1-1/4"

#7 x 1-1/8"

#8 x 1-3/8"

#8 x 2"

#8 x 2-1/2"

#8 x 3"

- (53433212)

- (52433014)

- (52043516)

- (52043520)

- (52043522)

- (52043530)

18 europecustomerservice@kidkraft.com

Hardware Identification

(Actual Size)

(7)

WB7 -

(10) WL3

(52613216)

(26)

WL5 - Wafer Lag

(2)

LS2 - Lag Screw

(5)

LS9 - Lag Screw

Wafer Bolt 5/16 x 3"

- Wafer Lag

1/4 x 1-3/8"

(2)

1/4 x 2-1/2"

H11 -

1/4 x 2-1/2"

(2) H5

5/16 x 4-3/4"

- (53613330)

18pc.

WB2 -

- (52613222)

Hex Bolt 1/4 x 2-3/4"

- (52213222)

Hex Bolt 1/4 x 4-1/2"

- (52213343)

Wafer Bolt 5/16 x 1-3/8"

(53613316)

- (53703223)

- (53703242)

(4)

WB9 -

(1)

WB8 -

(7) WB10 -

(19)

H10 -

(8) H3

Wafer Bolt 5/16 x 2-1/8"

Wafer Bolt 5/16 x 2-3/8"

Wafer Bolt 5/16 x 2-5/8"

Hex Bolt 1/4 x 2-1/4"

Hex Bolt 1/4 x 2-1/2"

(15) H1

(53703212)

- (53703221)

Hex Bolt 1/4 x 1-1/2"

- (53613324)

- (53613326)

- (53613329)

- (53703222)

(4)

G21 -

(2) G5 -

(12)

G13 -

(1)

G20 -

(2)

Hex Bolt 1/4 x 3-1/2"

H13 -

Hex Bolt 5/16 x 3-3/4"

1pc. G4

Hex Bolt 5/16 x 4-1/2"

Hex Bolt 5/16 x 6-1/8"

Hex Bolt 3/8 x 4"

- (53703840)

- (53703232)

- (53703333)

Hex Bolt 5/16 x 4"

- (53703342)

- (53703364)

(2)

- (53703340)

Hex Bolt 1/4 x 3"

H12H2

- (53703230)

(1) - Hex Bolt 1/4 x 2" - (53703220)

(6) H9

(53703211)

Hex Bolt 1/4 x 1-1/4"

(4)

(1)

G26 -

19 europecustomerservice@kidkraft.com

Hex Bolt 3/8 x 6"

G17 -

Hex Bolt 3/8 x 9-1/4"

- (53703860)

- (53703891)

Part Identification

- TNR 4 Post Mount

Clamp

(9203657)

30x

- 1/4 x 12.7mm Pan Head Bolt

(53453202)

- Steel Hand Grip

(9200211) -Yellow

- TNR 4 Post Mount

(9203656)

- TNR 4 Post Mount

31x

Base

(9203655)

(Reduced Part Size)

- Square Nylok Nut (54902200)

- 1/4 x 14.5mm Pan Head Bolt

(53452209)

- EN71 Hand Rail (3200224) -Yellow

Summit/KidKraft

Plaque

(9320358)

- KK Playset Plaque

(9320370)

- Cedar

- Plastic Formed

Washer (18 Pk)

(3290000)

- Rocks (10pk) (3320012)

- Horseshoe Bell Set (3200307)

- Telescope w/ Mount (3320161)

- Rebar Ground

Stake (6 Pk)

(3200318)

Chalkboard Flag

(3320716)

- Map Chalk Doodle Board (9320719)

- Acro Handle

(9200133)

- Swing

Belt Seat

(9320130)

- Door Hardware (3200710)

- Welded Chain (3200173)

2x 20" Chain

- MOD 5 Pane Window (2Pk) (3330502)

- Quadrex Driver

(9200015)

- Rope Ladder (3700204)

2x 9207712 Door Hinge

9207713 Door Catch

1x Magnetic Catch 1x Catch Plate

2x 9207711 Door Handle

4x 48" Chain

- Steering Wheel (3320255)

- #2 x 2"

Robertson Driver

(9200014)

- Acro Bar

(9200131)

- Heavy Bracket Set (3205701)

- Heavy L-Bracket (9200151)

- Heavy C-Bracket (9200153)

- Heavy Flat Bracket (9200149)

- TNR Tube Support Long

(9200268)

- 12' Climbing Rope 5/8" (3502150)

- DX Swing Hangers

with Quick Links (6 Pk)

(3201950)

(2 Pk)(3205960)

- Maze N Wave Double Slide Yellow (3318220)

- BBQ Deluxe Kitchen

- Utensil Shelf

9321691

3332608

- BBQ Lid

9327812

- BBQ Cooktop

33326909

- Playset Bracket Set (3205945)

- Flat Panel Bracket (8 Pk)(3205942)

- Flat Bracket

- Narrow Angle

Bracket (3 Pk)

(3205940)

- 3/8" Drill Bit

Set (3330008)

- BBQ Sink Set

- BBQ Base

3331611

- Corner

Bracket (6 Pk)

(3205979)

- Corner Panel

Bracket (6 Pk)

(3205977)

(angled)(4 Pk)

- Crow Ladder

Grip

(9200235)

- BBQ Utensils

3331610

- Basket with

Fruit 3330015

- Sign

9331614

1x - Front Wall

- Front Wall

Bracket (angled)

Bracket

(4 Pk) (3205948)

(4 Pk)

(angled)

(3205948)

- Wall Bracket

(

3205949

)

europecustomerservice@kidkraft.com

Step 1: Inventory Parts - Read This Before Starting Assembly

STOP STOPSTOP STOP

This is the time for you to inventory all your hardware, wood and accessories,

referencing the parts identication sheets. This will assist you with your assembly.

• The wood pieces will have the key number stamped on the ends of the boards. Organize the wood pieces by step, as per the key numbering system below.

2X 012 Post 2 x 4 x 83”

Quantity Key Number Part Description,

• Please refer to Page 6 for proper hardware assembly.

Part Size

Key Number: The rst two digits represent the step

number. The third digit represents the piece. Note that if the part is used in multiple steps then the

number only reects the rst step it is used in.

• Each step indicates which bolts and/or screws you will need for assembly, as well as

any at washers, lock washers, t-nuts or lock nuts.

B. If there are any missing or damaged pieces or you need assistance with

assembly please contact the consumer relations department directly. Call us before going back to the store.

customersupport@kidkraft.com Online Parts Replacement: Cedarsummitplay.com/parts-centerwarranty-claim Customer Service: 1(800) 933-0771 or (972) 385-0100

C. Read the assembly manual completely, paying special attention to ANSI warnings;

Europe Customer Service: +31 (0)20 305 8620

europecustomerservice@kidkraft.com EU Online Parts Replacement: parts.kidkraft.eu

notes; and safety/maintenance information on pages 1 - 6.

D. Before you discard your cartons ll out the form below.

• The carton I.D. stamp is located on the end of each carton. The tracking number is located on the Cedar Summit ID Plaque (9320357).

• Please retain this information for future reference. You will need this information if you contact the Consumer Relations Department.

MODEL NUMBER: F25745

CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)

CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)

CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 3)

TRACKING NUMBER (from ID Plaque):

21 europecustomerservice@kidkraft.com

CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 4)

CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 5)

CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 6)

Step 2: Access Ladder/Rope Wall Assembly Part 1

A: Place (021) Left Access on one side of 4 (023) Treads and (022) Right Access on the other side with the

grooves facing in. (g. 2.1)

B: Fit each (023) Tread into grooves on both (021) and (022) Access rails, making sure the top edge of the (023)

Treads are ush to the front of the Access rails. (g. 2.1 and 2.2)

C: Pre-drill pilot holes with a 1/8” drill bit and attach rails and treads together using 4 (S3) #8 x 2-1/2” Wood

Screws per tread. (g. 2.1)

Fig. 2.1

023

Flush to top edge

022

021

Fig. 2.2

End View

Flush to edges

Wood Parts Hardware

1 x Left Access 1-3/8 x 2-1/2 x 57-53/64”

021

022

1 x Right Access 1-3/8 x 2-1/2 x 57-53/64”

023

4 x Tread 15/16 x 3-1/4 x 19-1/2”

16 x #8 x 2-1/2” Wood Screw

023

Top Edge of Access Rail

Step 2: Access Ladder/Rope Wall Assembly Part 2

D: Making sure that the pre-sunk holes are facing the outside, place (024) Rope Rail on the ground next to

(022) Right Access so it matches the orientation of the two access rails as shown in g. 2.5. Attach (025) RW-AL Support ush to the top of Access Ladder assembly and (024) Rope Rail using 3 (S20) #8 x 1-3/8” Wood Screws

in the top holes and 3 (S11) #8 x 2” Wood Screws in the bottom holes. Pilot holes in (025) RW-AL Support should be centred over the rails. (g. 2.3 and 2.4)

E: Place one end of the (026) Access Rope Ladder Gap on the (021) Left Access and the other end on the (024) Rope Rail so there is a 1-3/8” gap between (026) Access Rope Ladder Gap and the top (023) Tread. Attach using

6 (S11) #8 x 2” Wood Screws. (g. 2.3)

F: Place (027) Rope Bottom between (024) Rope Rail and (022) Right Access and attach using 4 (S4) #8 x 3” Wood Screws. (g. 2.5)

Fig. 2.4

S20

x 3 in top holes

Flush

Fig. 2.3

Fig. 2.5

S11

025

x 3 in bottom holes

025

S11

026

023

x 6

026

021

1-3/8” gap between top

Tread and Ladder Gap

022

027

022

024

S20

S11

Wood Parts Hardware

024

1 x Rope Rail 2 x 2-1/2 x 57-13/16”

025

1 x RW-AL Support 5/8 x 3-1/4 x 41-3/4”

026

1 x Access Rope Ladder Gap 5/8 x 3-1/4 x 41-3/4”

027

1 x Rope Bottom 1-1/4 x 2-1/2 x 18-3/4”

S11

9 x #8 x 2” Wood Screw

S20

3 x #8 x 1-3/8” Wood Screw

4 x #8 x 3” Wood Screw

Nest Access Ladder

Step 3: Nest Ladder Assembly

A: Place (031) Nest Left Access on one side of 3 (033) Nest Treads and (032) Nest Right Access on the other

side with the grooves facing in. (g. 2.1)

B: Fit each (033) Nest Tread into grooves on both (031) and (032) Access rails, making sure the top edge of the

(033) Nest Treads are ush to the front of the Access rails. (g. 2.1 and 2.2)

C: Pre-drill pilot holes with a 1/8” drill bit and attach rails and treads together using 4 (S3) #8 x 2-1/2” Wood

Screws per tread. (g. 2.1)

D: Place (034) Nest Ladder Gap on each access rail so there is a 2-3/8” gap between (034) Ladder Gap and the

top (033) Nest Tread. Attach using 4 (S20) #8 x 1-3/8” Wood Screws. (g. 3.3)

E: Center a second Ladder Gap between the bottom Tread and the bottom ends of the access rails and attach using 4 (S20) #8 x 1-3/8” Wood Screws.

Fig. 3.1

031

Fig. 3.3

033

x 6 per side

034

032

Flush to top edge

Fig. 3.2

End View

Flush to edges

033

Top Edge of Access Rail

S20

x 2 per side

034

2-3/8” gap between top

Tread and Ladder Gap

Wood Parts

031

1 x Nest Left Access 1-3/8 x 2-1/2 x 41-1/8”

032

1 x Nest Right Access 1-3/8 x 2-1/2 x 41-1/8”

033

3 x Nest Tread 15/16 x 3-1/4 x 17-1/2”

034

2 x Nest Ladder Gap 5/8 x 3-1/4 x 19”

12 x #8 x 2-1/2” Wood Screw

8 x #8 x 1-3/8” Wood Screw

Hardware

S20

Step 4: Nest Joist Assembly

A: Place (041) Nest Mid Joist between (042) Front Wall Tie and (043) Back Wall Tie as shown in g. 4.1 making

sure to closely follow the hole orientation. Attach using 4 (S3) #8 x 2-1/2” Wood Screws. (Fig. 4.1)

B: Using the next set of pre-drilled holes on the (043) Back Wall Tie attach the (044) Nest Side Joist using 2 (S3) #8 x 2-1/2” Wood Screws. (Fig. 4.2)

C: Place (045) Ladder Side Joist between (041) Nest Mid Joist and (044) Nest Side Joist and attach using 4 (S3)

#8 x 2-1/2” Wood Screws as shown in g. 4.3.

Fig. 4.1

043

042

041

Fig. 4.2

Note hole orientation

043

041

045

044

Wood Parts Hardware

041

1 x Nest Mid Joist 1-1/4 x 2-3/8 x 33-3/4”

042

1 x Front Wall Tie 1 x 2-3/8 x 34-1/16”

043

1 x Back Wall Tie 1 x 2-3/8 x 34-1/16”

044

1 x Nest Side Joist 1-1/4 x 2-3/8 x 13-11/16”

045

1 x Ladder Side Joist 1-1/4 x 2-3/8 x 5-1/2”

10 x #8 x 2-1/2” Wood Screw

Step 5: Large Rock Wall Frame Assembly

8 Places

4 Places

Part 1

It is important to note the beveled edges on all horizontal boards.

A: Place (051) Rock Wall H and (052) Rock Wall I together so that they are connected at the notched ends.

Attach using 1 (H10) 1/4 x 2-1/4” Hex Bolt (with lock washer, at washer and t-nut). (Fig. 5.1 and 5.2)

B: Taking care to note the hole orientation place (053) Rope Support Back so that it lines up with the center holes on (051) Rock Wall H and place (054) Rock Wall Floor Cross so that it lines up with lower set of holes. Attach

each board using 1 (WB2) 5/16 x 1-3/8” Wafer Head Bolt (with at washer and t-nut) and 2 (S20) #8 x 1-3/8” Wood Screws as shown in g. 5.3 and 5.4.

C: Place (055) Rock Wall Short Cross so that it lines up with the upper holes on (052) Rock Wall I and place (056) Rock Wall Bottom Cross so that it lines up with the bottom holes, making sure that the pre-drilled rope hole

is at the bottom. Attach boards using 1 (WB2) 5/16 x 1-3/8” Wafer Head Bolt (with at washer and t-nut) and 2

(S20) #8 x 1-3/8” Wood Screws. (Fig. 5.3 and 5.4)

D: Flip frame assembly over and install (058) Rock Wall C as shown in g. 5.5 making sure to note the hole orientation. Attach using 4 (WB2) 5/16 x 1-3/8” Wafer Head Bolt (with at washer and t-nut) and 8 (S20) #8 x

1-3/8” Wood Screws. (Fig. 5.3 and 5.4)

Fig. 5.1

Fig. 5.3

Fig. 5.4

5/16” at

washer

Fig. 5.2

1/4” t-nut

1/4” at

washer

051

H10

1/4” lock washer

052

S20

WB2

5/16” t-nut

053

058

054

055

beveled edge on this side

056

for all horizontal boards

Wood Parts

051 056

1 x Rock Wall H 1-1/4 x 2-1/4 x 75-63/64”

052

1 x Rock Wall I 1-1/4 x 2-1/4 x 52-49/64”

053

1 x Rope Support Back 1-1/4 x 3 x 29-13/32”

054

1 x Rock Wall Floor Cross 1-1/4 x 3 x 29-13/32”

055

1 x Rock Wall Short Cross 1-1/4 x 3 x 21-13/16”

1 x Rock Wall Bottom Cross 1-1/4 x 3 x 21-13/16”

1 x Rock Wall C 1-1/4 x 2-1/4 x 92”

058

16 x #8 x 1-3/8” Wood Screw

1 x 1/4 x 2-1/4” Hex Bolt (with 1/4” lock

washer, 1/4” at washer and 1/4” t-nut)

8 x 5/16 x 1-3/8” Wafer Head Bolt

(5/16” at washer, 5/16” t-nut)

Hardware

S20

H10

WB2

Step 5: Large Rock Wall Frame Assembly

8 Places

4 Places

Part 2

E: Taking care to note hole orientation place (063) Rock Wall A as shown in g.5.6 and attach to (053) Rock

Support Back and (054) Rock Wall Floor Cross using 2 (WB2) 5/16 x 1-3/8” Wafer Head Bolt (with at washer and t-nut) and 4 (S20) #8 x 1-3/8” Wood Screws. (Fig. 5.5 and 5.6)

F: Attach (059) Rock Wall Angle Cross to (063) Rock Wall A and (058) Rock Wall C using 2 (WB2) 5/16 x 1-3/8

Wafer Head Bolt (with at washer and t-nut) and 4 (S20) #8 x 1-3/8” Wood Screws as shown in g. 5.5 and 5.6.

Fig. 5.5

058

063

059

WB2

5/16” at

washer

Fig. 5.6

S20

5/16” t-nut

Wood Parts

063

1 x Rock Wall A 1-1/4 x 2-1/4 x 84”

059

1 x Rock Wall Angle Cross 1-1/4 x 3 x 13-3/4”

8 x #8 x 1-3/8” Wood Screw

4 x 5/16 x 1-3/8” Wafer Head Bolt

(5/16” at washer, 5/16” t-nut)

Hardware

S20

WB2

6 places

Step 6: Narrow Wall Frame Assembly

A: Place (051) Rock Wall H and (062) Narrow Wall D together so that they are connected at the notched ends.

Attach using 1 (H10) 1/4 x 2-1/4” Hex Bolt (with lock washer, at washer and t-nut). (Fig. 6.1 and 6.2)

B: Place (057) Narrow Wall A on the left side of the frame assembly so that the top ends of the boards line up,

making sure to note hole orientation. Place 1 (064) Narrow Wall Cross in each of the 2 locations shown in g.

6.3 and attach using 2 (WB2) 5/16 x 1-3/8” Wafer Head Bolts (with at washer and t-nut) and 4 (S20) #8 x 1-3/8” Wood Screws per board. (Fig. 6.3 and 6.4)

C: Place (065) Narrow Wall Angled Cross as shown in g. 6.3 and attach using 2 (WB2) 5/16 x 1-3/8” Wafer Head Bolts (with at washer and t-nut) and 4 (S20) #8 x 1-3/8” Wood Screws per board. (Fig. 6.3 and 6.4)

Fig. 6.1

051

1/4” t-nut

Fig. 6.2

1/4” at

washer

Fig. 6.4

062

1/4” lock washer

H10

Fig. 6.3

057

Note hole orientation

S20

Narrow Rock Wall Frame, Front View

064

065

057

5/16” t-nut

065

062

WB2

5/16” at

washer

Wood Parts

051

1 x Rock Wall H 1-1/4 x 2-1/4 x 75-63/64”

062

1 x Narrow Wall D 1-1/4 x 2-1/4 x 52-49/64”

057

1 x Narrow Wall A 1-1/4 x 2-1/4 x 84”

064

2 x Narrow Wall Cross 1-1/4 x 3 x 8-3/32”

065

1 x Narrow Wall Angled Cross 1-1/4 x 3 x 11-1/4”

12 x #8 x 1-3/8” Wood Screw

1 x 5/16 x 1-3/8” Hex Bolt (with 1/4” lock washer,

1/4” at washer and 1/4” t-nut)

6 x 5/16 x 1-3/8” Wafer Head Bolt

(5/16” at washer, 5/16” t-nut)

Hardware

S20

H10

WB2

Step 7: Slide Wall Assembly

A: Place (072) Narrow Panel Back against the left side of (071) Nest End Panel noticing panel orientation. The

tops and bottoms of the panels should be ush and panels square. Pre-drill with a 3/16” drill bit, then fasten

(072) Narrow Panel Back to (071) Nest End Panel with 4 (WL5) 1/4 x 2-1/2” Wafer Lags. (Fig. 7.1, 7.2 and 7.4)

B: Place (073) Narrow Front Panel against the right side of (071) Nest End Panel noticing panel orientation. The

tops and bottoms of the panels should be ush and panels square. Pre-drill with a 3/16” drill bit, then fasten

(071) Nest End Panel to (073) Narrow Front Panel with 4 (WL5) 1/4 x 2-1/2” Wafer Lags. (Fig. 7.1, 7.3 and 7.4)

Fig. 7.2

Notice (072) Narrow Back Panel overlaps (071) Nest End Panel

Flush

072

WL5

071

Fig. 7.1

073

Fig. 7.3

Notice (071) Nest End Panel overlaps (073) Narrow Front Panel

WL5

Flush

071

Fig. 7.4

WL5

071

Flush

Wood Parts

071

1 x Nest End Panel 1-1/4 x 37 x 92”

072

1 x Narrow Panel Back 1-1/4 x 21-1/2 x 92”

073

1 x Narrow Front Panel 1-1/4 x 21-1/2 x 92”

8 x 1/4 x 2-1/2” Wafer Lag

Hardware

WL5

Step 8: Swing Wall Assembly

A: Place (082) Panel Front Wall against the left side of (081) SW Wall Panel noticing panel orientation. The tops

and bottoms of the panels should be ush and panels square. Pre-drill with a 3/16” drill bit, then fasten (082) Panel Front Wall to (081) SW Wall Panel with 4 (WL5) 1/4 x 2-1/2” Wafer Lags. (g. 8.1 and 8.2)

B: Place (083) Wall Panel Back against the right side of (081) SW Wall Panel noticing panel orientation. The

tops and bottoms of the panels should be ush and panels square. Pre-drill with a 3/16” drill bit, then fasten (081) SW Wall Panel to (083) Wall Panel Back with 4 (WL5) 1/4 x 2-1/2” Wafer Lags. (g. 8.1 and 8.3)

Flush

Fig. 8.2

Flush

082

081

Fig. 8.1

Fig. 8.3

083

Notice (081) SW Wall Panel overlaps (083) Back Wall Panel

081

Notice (082) Front Wall Panel overlaps (081) SW Wall Panel

WL5

081

Flush

Wood Parts

081

1 x SW Wall Panel 1-1/4 x 37 x 92”

082

1 x Panel Front Wall 1-1/4 x 43 x 92”

083

1 x Wall Panel Back 1-1/4 x 43 x 92”

8 x 1/4 x 2-1/2” Wafer Lag

Hardware

WL5

+ 105 hidden pages

KidKraft Cedar Summit Lookout Extreme, Cedar Summit F25745 Installation And Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual