Kidde 0910 User Manual

Sealed Battery

10

U

L

SIGNALING

LISTED

Smoke Alarm with Smart Hush

• Model 0910 • Part Number 900-0136

LED Indicator

A flashing red indicator light with four modes of
operation: Standby, alarm mode, hush mode and
memory set

Test/Reset Button

One button tests the unit’s circuit operation and resets
memory after an alarm condition occurs

TM

Smart Hush

Temporarily silences nuisance alarms. Will not allow
hush to be activated unless unit is in alarm mode.

Battery Operated

No wiring needed

Sealed-In Lithium Batteries

Unit will continue to operate for 10 years

TM

Feature

Description

The Kidde 0910 is a 10-year, sealed battery, ionization,
smoke alarm with Alarm Memory and Smart Hush
feature. The innovative design of this alarm’s automatic
activation is unlike any other smoke alarm. The 0910
alarm will automatically activate when it is attached to
the mounting bracket; there are no pull-tabs, no switches,
everything is automatic. At the end of the alarm life, the
unit will chirp, indicating the alarm is in need of replace­ment. The customer can use a simple tool such as a
screwdriver to deactivate the unit, stopping the low bat­tery chirp and making it safe for disposal.
The sealed-in board-mounted batteries will power the
0910 unit for its complete 10-year life. No replacement
batteries will ever be needed.

TM

Consumer Benefits

The Kidde 0910 sealed battery operated smoke alarm
features a self-activation mechanism making installation
simple and easy. It also features Smart Hush
allowing consumers to temporarily silence nuisance alarms
and an End of Life Alert indicating it is time to replace the
alarm.
At the end of the alarm’s 10-year life, deactivation
of the alarm is just as easy. Using a tool such as a small
screwdriver, a deactivation switch removes power from
the alarm and renders the batteries safe for disposal. The
alarm lockout feature mechanically prevents a deactivated
unit from being mounted back on the mounting bracket.

TM

Control

Features and Benefits

• Sealed-InLithiumBattery – Sealed-in lithium power
supply; no battery replacement required over the 10
year life of the alarm. Eliminates worry about battery
removal or unauthorized deactivation of alarm.

• SelfActivation – Alarm automatically activates when
attached to the mounting bracket.

• AlarmMemory – Rapidly flashing LED alerts user if the
alarm has sounded since the last time the test/reset
button was used.

• SmartHush

alarms and will not allow hush mode to be activated
unless the unit is in alarm mode.

• Test/ResetButton – Tests unit’s circuit operation and
resets memory after an alarm condition occurs.

• EndofLifeWarning – Alarm chirps every 30-45
seconds indicating the alarm is in need of replacement.

• TamperResist – (when activated upon installation)
effective in preventing someone from removing the unit
from the mounting bracket.

• LED – A flashing red indicator light
with four modes of operation:
standby, alarm mode,
hush mode, and memory set.

TM

– Will temporarily silence nuisance

Sealed Battery Unit

5.6" 1.55"

Smoke Alarm with Hush

TM

Model 0910
Part Number 900-0136

Architectural and Engineering
Specifications

The smoke alarm shall be Kidde unit 0910/0910CA or approved
equal. It shall be powered by a non-replaceable lithium battery with a
10-year life. The lithium battery shall be sealed in the unit to prevent
removal and/or tampering. The unit shall incorporate an ionization
sensor with nominal sensitivity of 0.99%/ft (.87%/ft for unit 0910CA).
The temperature operating range shall be between 40°F and 100°F
(4°C and 38°C) and the humidity operating range shall be 5% - 95%
relative humidity.

The smoke alarm can be installed on the surface of any wall or ceil­ing following the UL/Manufacturer’s approved placement guidelines.
The alarm shall incorporate an automatic activation feature that will
activate the unit as soon as it is attached to the mounting bracket, no
other steps are involved. The alarm shall provide optional tamper resis­tance that locks the unit to the mounting bracket and deters removal
of the unit from the wall or ceiling.

The alarm shall include a test button that will simulate a fire condition
and cause the unit to go into alarm. This sequence tests the unit’s
electronics to ensure proper operation.

The unit shall include a piezoelectric horn that is rated at 85 decibels
at 10 feet. The unit shall include the Smart Hush
the unit for approximately 7 minutes if a nuisance condition occurs.
The red LED will illuminate for 1.5 seconds every 8 seconds and will
automatically reset itself. If the alarm is in the Hush mode and the
condition that triggered the alarm persists, the alarm shall sound again
to signal potential danger despite its presence in Hush Mode.The unit
shall incorporate one red LED to indicate the alarm’s current status
and mode of operation. The LED will indicate one of four modes:

Standby Mode: LED will flash every 40-45 seconds to indicate
the unit is operating correctly

Alarm Mode: LED will flash every 1.5 seconds to indicate the
unit is alarming and will be accompanied by the
horn sounding

Hush Mode: LED will illuminate for 1.5 seconds every 8
seconds to indicate the unit is temporarily silenced

Memory Set Mode: If Alarm Memory has been set, the LED will
flash rapidly when the test button is pressed.

TM

feature that silences

The unit shall include an End of Life Alert which is indicates the
alarm needs to be replaced. The unit will “chirp” once every 30
seconds to notify the user. The unit shall have a deactivation switch
to disable it and make it safe for disposal. The unit shall at a mini­mum meet the requirements of UL217, NFPA72, (chapter 11 2002
edition) The State of California Fire Marshall, NFPA101 (One and
two family dwellings) Federal Housing Authority (FHA), Housing
and Urban Development (HUD).

Technical Specifications

Model: 0910

UPC Number: 0-47871-90136-4

Power Source: Three, 3V Lithium batteries

Sensor: Ionization

Audio Alarm: 85dB at 10ft

Temperature Range: 40˚F (4.4˚C) to 100˚F (37.8˚C)

Humidity Range: 5%-95% relative humidity (RH)

Size: 5.6” in diameter x 1.55” depth

Weight: 1.5lbs

Interconnects: No

LED: Four modes of operation

Warranty: 10 year limited

Ordering Information

Clamshell UPC: 0 47871 90136 4

Part Dimensions Case/ Layers/ Skid

Number I2of5 PackQuantity (wxdxhinches) Weight Skid Skid Weight

900-0136 N/A N/A Individual 7.25 x 1.75 x 11 1 lbs N/A ----- N/A

900-0136-003 100 47871 90136-1 PDQ (3 units) 7.75 x 6 x 11.75 3 lbs 108 ----- 972 lbs

900-0136-020 200 47871 90136-8 Master Pack (20 units) 16 x 24 x 12 20 lbs 12 ----- 240 lbs

21007387 400 47871 90136-2 4pc Tray and Lid 7.75 x 9.25 x 11.75 4 lbs 75 300 lbs

Distributed by:

1016 Corporate Park Drive
Mebane NC 27302
1-800-880-6788
www.Kidde.com

revised 10/2008