Kicker ZX150.2, ZX200.2, ZX250.2 User Manual

ZX
STEREOAMPLIFIER
ZX150.2, ZX200.2, ZX250.2
©2006 Stillwater Designs
Installation . . . as easy as 1, 2, 3
1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The controls on the
top of the amplifier need to be accessible for adjustment. Make sure there are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier.
2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then connect the ground wire to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and corrosion-free solid-metal area of the vehicle's chassis. Adding an additional ground wire between the battery's negative post and the vehicle chassis of this same gauge (or larger) is recommended.
Use a twisted pair of RCA (low-level) interconnect cable to feed the audio signal to the amplifier. Only use speaker wire (high-level) inputs if your source unit does not have RCA type outputs. Either input method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to another amplifier or component (P.A.S.T.). Keep the RCA cable away from factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifier. If you ever need to remove the amplifier from the vehicle after it has been installed, the ground wire should be the last wire disconnected from the amplifier--just the opposite as when you installed it. See the chart below for power and ground wire size, and fusing recommendations.
3. Configuration The following diagrams show the most common configurations for your Kicker ZX series amplifier.
Two Channel Operation (Stereo) These ZX amplifiers are capable of operating into a minimum impedance of 2 ohms per channel in stereo operation. See Figure 2.
Bridged Operation (Mono) ZX.2 series amplifiers are capable of operating into a minimum impedance of 4 ohms when in bridged operation. See Figure 3.
Stereo and Mono Operation Simultaneously (SAMS) The ZX.2 series amplifiers are capable of operating into a minimum impedance of 4 ohms mono and 2 ohms per channel in stereo simultaneously with the use of passive crossovers. See Figure 4.
INSTALLATION
ZX.2AMPLIFIER
ZX150.2 / ZX200.2 / ZX250.2
TwoChannelModels:
ZX.2SeriesAmplifier
Owner’sManual
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
Authorized Kicker Dealer:
Purchase Date:
Amplifier Model Number:
Amplifier Serial Number:
__________________________
__________________________
__________________________
__________________________
ModelZX150.2 Fuse25A PowerGroundWire 8GA ModelZX200.2 Fuse30A PowerGroundWire 8GA ModelZX250.2 Fuse40A PowerGroundWire 8GA
Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.
2 3
Figure 1
Figure 2
Figure 3
Figure 4
Use only one type of signal input to the amplifier,
either RCA Cable or Speaker Wire
RCA Cable (Low-Level)
Input
Speaker Wire
(High-Level
Output)
Speaker Wire
(High-Level Input)
Left + Left ­Right ­Right +
CONFIGURATION
RCA Cable (Low-Level)
Output
Crossover Switch
Signal Out
(P.A.S.T.)
Battery
Remote Turn-On
+12V
(45cm)
18"
Or Less
Ground
(60cm)
Or Less
Fuse
24"
Minimum impedance of 2 ohms per channel in stereo operation
Minimum impedance of 4 ohms when in bridged operation
Right Speaker
_
R-
R+
L-
L+
+
Signal Out (P.A.S.T.)
Signal In
_
+
Left Speaker
killers trk7“on Top”
SOURCE UNIT
RL
RL
OUTPUT
OFF HI LO
XOVER
HI-LEVEL
INPUT
+ - - +
INPUT
L+ L-R+R-
Battery
Battery
Remote Turn-On
+12V
(45cm)
18"
Or Less
Remote
Turn-On
+12V
Ground
(45cm)
18"
Or Less
Ground
(60cm)
Or Less
Fuse
24"
(60cm)
Or Less
Fuse
24"
Minimum impedance of 4 ohms mono and 2 ohms per channel in
stereo simultaneously with the use of passive crossovers
R-
R+
L-
L+
Signal Out (P.A.S.T.)
Signal In
Mono
Speaker
_
+
Right Speaker
_
R-
R+
L-
L+
HIGH PASS CROSSOVER
Signal Out (P.A.S.T.)
Signal In
HIGH PASS CROSSOVER
+
Speaker
_
+
Left Speaker
Mono
_
+
CROSS-
LOW PASS
OVER
Loading...
+ 2 hidden pages