Kicker ZX1500.1, ZX2500.1 Owner's Manual

ZX
SUBWOOFERAMPLIFIER
CLASS-DMONOCHANNEL
ZX1000.1, ZX1500.1, ZX2500.1
©2007 Stillwater Designs
ZX.1SeriesAmplifi er
>
>
Owner’sManual
MonoChannel: ZX1000.1 / ZX1500.1 / ZX2500.1
Congratulations on your
KICKER purchase!
Please record your purchase
information and keep your sales
receipt for validation of warranty.
Authorized Kicker Dealer:
Purchase Date:
Amplifi er Model Number:
Amplifi er Serial Number:
Installation
1. Mounting Choose a structurally sound location to mount your Kicker amplifi er. Make sure there
are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er.
2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint and corrosion free solid metal area of the vehicle's chassis. Adding an additional ground wire of this same gauge (or larger) between the battery's negative post and the vehicle chassis is recommended.
The ZX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals from your car stereo’s source unit. Ideally, when connecting the source unit to the amplifi er, the ZX amplifi er’s input level switch should be set to “LO” and a low-level signal should run from the source unit’s stereo RCA output to the stereo RCA input on the end panel of the amplifi er using RCA interconnect cable. If a low-level stereo RCA output is not available on the source unit, the signal can be delivered to the amplifi er using the high-level speaker outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “HI”. Crimp and solder RCA connectors to the end of the speaker wire running from the high-level speaker outputs on the source unit and connect the wire to the RCA Inputs on the end panel of the amplifi er as shown in Figure 1. Either input method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to another amplifi er or component. Keep the audio signal cable away from factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
Install the provided external fuse within 18” (45cm) of the ZX amplifi er and in-line with the power cable. Install a second fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. These ZX series mono amplifi ers deliver Kilo-Watts of power. We recommend an alternator
Core Cable
+
INSTALLATION
High-level Speaker Output Wire
To Source Unit
with a minimum 140 ampere output capacity, at least one extra battery located within 50” (130cm) to the amplifi er, an extra fuse located within 18” (45cm) of the extra battery, all power and ground feeds to be as short as possible, and utilize 12, 10 or 8 gauge speaker wire. See Figure 2. If you ever need to remove the amplifi er from the vehicle after it has been installed, the ground wire should be the last wire disconnected from the amplifi er--just the opposite as when you installed it. See the chart below for power and ground wire size, and fusing recommendations.
ModelZX1000.1 1 (ONE) 100 AMPERE FUSE PowerGroundWire 1/0GA ModelZX1500.1 1 (ONE) 150 AMPERE FUSE PowerGroundWire 1/0GA
2
ModelZX2500.1 1 (ONE) 300 AMPERE FUSE PowerGroundWire 1/0GA
ZX.1AMPLIFIER
+
Ground or Shielding
__________________________
__________________________
__________________________
__________________________
Figure 1
To Amplifi er
3. Confi guration The following diagram shows the most common confi gurations for your Kicker ZX series amplifi er.
One Channel Operation These ZX amplifi ers are capable of operating into a minimum impedance of 2 ohms. If you are using multiple voice coils, the net impedance of the voice coils must be equal to or greater than 2 ohms.
KUNEK
Figure 2
One Channel Operation (Mono)
Minimum impedance of 2 ohms while in bridged operation
Ground
Remote Turn-On
(45cm)
18"
Battery
+12V
Fuse
(60cm)
24"
10 - COMA
Source Unit
CONFIGURATION
Signal Out
Signal In
Performance
Model ZX1000.1 ZX1500.1 ZX2500.1
RMS Power in Watts, all channels driven @14.4 Volts, 4Ω mono, 1% THD+N
+
@ 2Ω mono, 1.5% THD+N 1000 x 1 1500 x 1 2500 x 1
Length: in(cm) 16 3/4 (42.5) 20 (50.7) 27 1/2 (69.7)
Specifi cations common to all models:
Height: in(mm) 2 1/8 (54mm) Width: in(mm) 9 5/8 (244mm) Frequency Response, ± 1 db: 25 Hz - 200 Hz Signal-to-Noise Ratio: >95db, a-weighted, re: rated power
Input Sensitivity:
Selectable Electronic Crossover: Variable Low-Pass, 50 - 200Hz, 24dB per octave Subsonic Filter 24 db/Octave Subsonic Filter Fixed @ 25Hz Bass Boost: Variable 0-18db Bass Boost @ 40Hz
Note: To get the best performance from your new Kicker Amplifi er, we recommend using genuine Kicker Accessories and Wiring.
500 x 1 750 x 1 1250 x 1
Low Level: 125mV-5V
High Level: 250mV-10V
3
Loading...
+ 2 hidden pages