Page 1
S15L5 / S12L5 / S10L5 / S8L5
Congratulations! You have just purchased one of the most advanced subwoofers in
the history of car audio. Your KICKER Solo-Baric is the latest in KICKER s trend-setting
Solo-Baric line, designed and engineered to deliver the ultimate in low bass performance and unmatched durability. Thanks for buying KICKER. Enjoy
!
Solo-Baric Features
NEW For 2002 !
yy
Increased Surround Radius Provides increased Xmax for more low bass output and higher SPL.
yy
WARG (Wrap ARound Gasket) One piece rubber front and rear gasket provides greater durability,
resistance to separation and provides a better seal to eliminate air leaks.
yy
SSD (Spun Spoke Design) Enhances the cosmetics and provides a solid anti-resonant foundation
for the motor assembly.
yy
Perimeter Venting the offset vents create a vortex cooling effect around the voice coil.
yy
ISD (Inverted Structural Dome
yy
Stitched Surround (patent pending) prevents cone/surround separation at high excursions.
yy
Dual Ultra-Length Voice Coils for enormous cone excursion and flexible wiring options.
yy
High-Temp Kapton Voice Coil Former for better sonic and thermal performance, prevents
cone meltdown.
yy
Blackened One Piece Uniplatewith Vented Hyper-Extended Pole
11..
provides enhanced heat transfer for cool operation and maximum power handling.
22..
reduces non-linear magnetic fields around the voice coil gap for superior cone motion control.
33..
releases pressure under ISD for freer cone motion and enhanced low bass.
yy
Sleeved High-Power Tinsel Lead Wires to resist lead breakage and power-robbing resistance
losses.
yy
Spring-Loaded Nickel Plated Terminals for solid connections with large gauge speaker wire.
))
further increases cone’s resistance to flex under pressure.
Page 2
SPECIFICATIONS
Dual 2 Ohm = 4 Ohm Load
Dual 4 Ohm = 8 Ohm Load
Dual 2 Ohm = 1 Ohm Load
Dual 4 Ohm = 2 Ohm Load
Specifications
Model Max amp Sensitivity Voice Xmax Mounting Outer Mounting
SS1155LL55
SS1122LL55
SS1100LL55
SS88LL55
Based on measurements of Dual 2 Ohm models
Power Coil Cutout Flange Depth
(watts) (dB 1w/1m) (in./
750 87.5 2.5 .61 13.75 x 13.75 15.6 x 15.6 7.84
600 86.9 2.0 .49 11.0 x 11.0 12.54 x 12.54 6.33
450 85.6 2.0 .49 9.25 x 9.25 10.66 x 10.66 5.69
300 83.2 2.0 .38 7.25 x 7.25 8.8 x 8.8 4.86
cm
) (in./cm) (in./cm) (in./cm) (in./cm)
6.35 1.55 34.92 x 34.92 39.6 x 39.6 19.91
5.08 1.25 27.94 x 27.94 31.85 x 31.85 16.08
5.08 1.25 23.49 x 23.49 27.08 x 27.08 14.45
5.08 .97 18.42 x 18.42 22.35 x 22.35 12.34
Wiring Options
Solo-Baric L5 woofers are available with dual 2 Ohm or dual 4 Ohm voice coils.
Both coils should always be hooked up.
The dual 2 Ohm woofer will give you a 1 Ohm or a 4 Ohm load depending on if
the coils are wired in parallel or in series. The dual 4 Ohm woofer will give a 2
Ohm or 8 Ohm load depending on how they are wired.
The terminals with solid red and black markings are for one voice coil. The terminals with the white dots are for the second voice coil.
Parallel Wiring
Dual 2 Ohm = 1 Ohm Load
Dual 4 Ohm = 2 Ohm Load
2
Series Wiring
Dual 2 Ohm = 4 Ohm Load
Dual 4 Ohm = 8 Ohm Load
Page 3
Cutout Dimensions
Corner Radius:
S15L5 - 1.0”
S12L5 - .625”
S10L5 - .625”
S8L5 - .625”
13.75"
11"
9.25"
7.25"
1 inch = 2.54cm
S8L5
S10L5
S12L5
S15L5
7.25"
9.25" 11" 13.75"
Box Building Notes
The cardboard support inside your Solo-Baric’s shipping carton can be used as a template
for cutting the speaker mounting hole in the enclosure you build. Since the cardboard cutout is the same size as the basket of the L5, when you make the cut along the line drawn
through the template, make sure to cut right on the line to get the correct opening size.
All the cubic feet numbers given in the following pages include the displacement of the
woofer. For the ported boxes the displacement of the port must be added to the final
design. It will be impractical to use round ports for these designs. The rectangular port
information given will yield the best results.
Always use 3/4" or thicker MDF and make sure all the
joints are secure and well sealed. The peak pressure in a
ported box can exceed that of a sealed enclosure.
All of these designs need some internal bracing. Be sure
to add 2"x 2"(5.08cm x 5.08cm) to 3"x 3"(7.62cm x 7.62cm)
triangle braces between each of the larger unsupported
panels. Kicker recommends using a good grade of wood
glue and silicone sealer for an airtight box.
Note: If you prefer an ultra-smooth bass response, you
should loosely fill your Solo-Baric Enclosure with polyfil.
Ported designs will require covering the entrance to the
port (inside the box) with hardware cloth, chicken wire, or
expanded metal to prevent the polyfil from being blown
out through the port. Use of polyfil will slightly decrease
efficiency, but will deepen and extend low bass response.
Do not install a ported box with the port against a solid
surface. The port opening must remain unobstructed. Use the smallest dimension of the
rectangular port as the minimum amount of space required between the port and any
surface to insure unrestricted airflow.
X
X = 3" x 3” for S15L5, S12L5
X = 7.62cm x 7.62cm
X = 2" x 2” for S10L5, S8L5
X = 5.08cm x 5.08cm
X
X
For more advice on box building, see the Choosing and Building Enclosures page in the
Tech Tips & FAQs section of the Support area on the Kicker website,
call Technical Services at 1-405-624-8583.
www.kicker.com
or
3
Page 4
A note on power haandling caapaability
Solo-Baric subwoofers will handle massive amounts of power in any of the recommended enclosures, minimum or maximum. The smaller enclosures are best for use in limited
space applications. The larger (maximum) recommended enclosures will yield slightly more
bass at the lowest frequencies. The power ratings given are assuming that both voice coils
are used. You should never hook up a dual voice coil woofer using only one coil.
Recommended Enclosures
Solo-Baric L5-Series Sealed Enclosure Applications
The Kicker Solo-Baric L5 is designed to give more output than an equivalent round
speaker and is amazing when used in the recommended sealed boxes. These sealed enclosure recommendations will give the smoothest response with the most energy at really
low frequencies, around 20 to 30 Hz.
The recommended Compact sealed boxes have the highest power handling capability of
all our recommended enclosure designs. They deliver massive amounts of high impact
bass and can be driven with punishing levels of amplifier power.
One of the benefits of the Solo-Baric L5-series high performance suspension system is
that they can operate in larger sealed enclosures for ultra sound quality (SQ) applications
without significantly sacrificing their power handling. Solo-Baric L5 enclosures can be "sized
up" all the way to a .707 Qtc enclosure, which has a very flat response, with greatly extended sub bass.
Solo-Baric L5 series woofers also perform well in any sealed enclosure between the
Compact and SQ sizes. These systems will exhibit some benefits of both (high impact and
low extension) generally sounding more like the box to which they are most closely sized.
These enclosure volume recommendations are for the airspace inside the enclosure and
include the displacement of the woofer. Do not make the airspace any greater than recommended.
Recommended Sealed Enclosures – Moderate Efficiency
Model Compact SQ (.707 alignment)
(Minimum enclosure Vol.) (Maximum enclosure Vol.)
S8L5 .33 cu.ft. Power Handling = 300W .75 cu.ft. Power Handling =300W
9.34 l 21.24 l
S10L5 .66 cu.ft. Power Handling = 450W 1.0 cu.ft. Power Handling = 450W
18.69 l 28.32 l
S12L5 .88 cu.ft. Power Handling = 600W 2.0 cu.ft. Power Handling = 600W
24.92 l 56.64 l
S15L5 1.5 cu.ft. Power Handling = 750W 6.0 cu.ft. Power Handling = 750W
42.48 l 169.92 l
The following page shows examples of the minimum enclosure sizes for each of the
Solo-Baric L5s. Panel dimensions assume 3/4" wood thickness.
4
Page 5
Panel dimensions for minimum recommended enclosures:
Model Volume (cu.ft.) Panel A Panel B Panel C
S8L5 0.33 10"x10" 10"x8" 8"X8.5"
S10L5 0.66 12"x12" 12"x10.5" 10.5"x10.5"
S12L5 0.88 13"x13" 13"x11.5" 11.5"x11.5"
S15L5 1.5 16.5"x16.5" 16.5"x11.5" 15"x11.5"
1 inch = 2.54cm
1cu.ft. = 28.32l
NOTE: All sealed boxes should be 50% filled with loose polyfil. Allow about two weeks
break-in time for the Solo-Barics to reach optimum low bass performance.
Solo-Baric L5-Series Ported/Vented Enclosure Applications
Ported Solo-Barics? Absolutely ... and with a vengeance! These enclosures incorporate
massive slot loaded ports with ultra low air velocity for ground pounding street bass that
will make your hair stand on end (if you have any left)! These are the type of boxes that are
the "enclosure of choice" for outrageous street bass and high performance SPL contests.
The following chart shows three recommended ported enclosures for each Solo-Baric
driver.
Compact has increased bass efficiency over a sealed enclosure, yet can still fit in tighter
applications. It is the smallest design that will work well for each woofer. Although it is the
smallest ported enclosure, the output from 30 to 80 Hz will be considerably higher than
that of a sealed box. The two other ported designs have proportionately more output in
this region.
Street Bass is a medium sized enclosure that will kick out bass that can be heard for
blocks away. And it does go LOW!
SPL / Deep Bass is a large enclosure with high efficiency that will deliver the output
needed to win SPL contests AND produce bass output all the way down to the basement.
We’re talking truly awesome!
If space is not at a premium and you want to get the most from your Solo-Baric L5, try
one of these designs. You won’t be disappointed.
Model Compact Street Bass SPL / Deep Bass
SS88LL55
SS1100LL55
SS1122LL55
SS1155LL55
NOTE: The use of a subsonic filter is necessary to insure the life of the woofer in a ported enclosure!
Without a subsonic filter assume a 30% decrease in power handling.
.66 cu.ft. + port; .8 cu.ft. + port; 1.0 cu.ft. + port;
1.5x9.5" port, 19.25" long 1.75x9.5" port, 19.75" long 2x9.5" port, 21.25" long
Power Handling = 300W Power Handling = 300W Power Handling = 300W
1.25 cu.ft. + port; 1.75 cu.ft. + port; 2.25 cu.ft. +port;
2.5x11.25" port, 19.75" long 2.75x11.25", port 17.75" long 3x11.25" port, 18" long
Power Handling = 425W Power Handling = 450W Power Handling = 450W
1.75 cu.ft. + port; 2.5 cu.ft. + port; 3.25 cu.ft. + port;
2.5x13.25" port, 22.5" long 2.5x13.25" port, 16.5" long 3x13.25" port, 14.5" long
Power Handling = 600W Power Handling = 600W Power Handling = 600W
3.0 cu.ft. + port; 4.5 cu.ft. + port; 6.0 cu.ft. + port;
2.5x16.25" port, 19.5" long 3x16.25" port, 14.75" long 3.5X16.25"port, 13.75"long
Power Handling = 750W Power Handling = 750W Power Handling =750W
Recommended Ported Enclosures – High Efficiency
5
Page 6
NOTES
6
Page 7
SPEAKER SYSTEMS LIMITED WARRANTY
Kicker warrants this product to be free from defects in material and workmanship under normal use
for a period of THREE (3) MONTHS from date of original purchase. When purchased from an
Authorized KICKER Dealer it is warranted for ONE (1) YEAR from date of original purchase. If the product
is labeled “B Stock” and purchased from an Authorized KICKER Dealer, it is warranted for THREE (3)
MONTHS from date of purchase, regardless of place of installation. Should service be necessary under this
warranty for any reason due to manufacturing defect or malfunction during the warranty period, Kicker
will replace or repair (at its discretion) the defective merchandise with equivalent merchandise at no
charge. Warranty replacements on “B-Stock” merchandise may have cosmetic scratches and blemishes.
Discontinued products may be replaced with more current equivalent products.
This warranty is valid only for the original purchaser and is not extended to owners of the product
subsequent to the original purchaser. Any applicable implied warranties are limited in duration to a period
of the express warranty as provided herein beginning with the date of the original purchase at retail, and
no warranties, whether express or implied, shall apply to this product thereafter. Some states do not
allow limitations on implied warranties, therefore these exclusions may not apply to you.
This warranty gives you specific legal rights; however you may have other rights that vary from state to
state.
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE
Defective merchandise must be returned to your local Authorized Stillwater Designs (Kicker) Dealer for
warranty. Assistance in locating an Authorized Dealer can be obtained by writing or calling Stillwater
Designs direct. You can confirm that a dealer is authorized by asking to see a current authorized dealer
window decal.
If it becomes necessary for you to return defective merchandise, call the Kicker Customer Service
Department at (405)624-8510 for a Return Authorization (RMA) number. Package all defective items in the
original container or in a package that will prevent shipping damage, and return to
Stillwater Designs, 5021 North Perkins Road, Stillwater, OK 74075
The RMA number must be clearly marked on the outside of the package. Return only defective components. Return of entire cabinets, system packs, pairs, etc. increases your return freight charges. Nondefective items received will be returned freight collect.
Include a dated proof-of-purchase stating the Customer name, Dealer name, product purchased
and date of purchase. Warranty expiration on items without proof-of-purchase will be determined from
type of sale and the manufacturing date code. Freight must be prepaid; items received freight collect will
be refused.
Failure to follow these steps may void your warranty. Any questions can be directed to the Kicker
Customer Service Department at (405)624-8510.
WHAT IS NOT COVERED?
This warranty is valid only if the product is used for the purpose for which it was designed.
It does not cover:
• Damage due to improper installation
• Subsequent damage to other components
• Damage caused by exposure to moisture,
excessive heat, chemical cleaners, and/or UV
radiation
• Damage through negligence, misuse, accident
or abuse. Repeated returns for the same
damage may be considered abuse.
• Any cost or expense related to the removal or
reinstallation of product
• Speakers damaged due to amplifier clipping or
distortion
HOW LONG WILL IT TAKE?
Kicker strives to maintain a goal of 24-hour service for all returns. Delays may be incurred
if lack of replacement inventory or parts is encountered.
• Items previously repaired or modified by any
unauthorized repair facility
• Return shipping on non-defective items
• Products with tampered or missing barcode labels
• Products returned without a Return Authorization
(RMA) number
• Freight Damage
• The cost of shipping product to Kicker
• Service performed by anyone other than Kicker
• Speaker with any foreign caulk used for gasket
material
INTERNATIONAL WARRANTY
Contact your International Kicker dealer or distributor concerning specific
procedures for your country’s warranty policies.
P.O. Box 459 • Stillwater, Oklahoma 74076 • U.S.A. • 405 624-8510
KICKER drivers are capable of producing sound levels that can permanently
damage your hearing! Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at
the same volume level. The threshold of pain is always an indicator that the
WARNING:
sound level is too loud and may permanently damage your hearing.
Please use common sense when controlling volume!
August 2002
Page 8
Loading...