Versión Español
SISTEMA ESTEREOFÓNICO DIGITAL PARA iPhone Y iPod
Manual dal Propietario
Deutsche Version
STEREOSYSTEM FÜR iPhone Und iPod iKICK DIGITAL
Benutzerhandbuch
Version Française
SYSTÈME STERÉO NUMÉRIQUE POUR iPhone Et iPod iKICK
Manual d`utilisation
®
Authorized KICKER Dealer:
Purchase Date:
DIGITALSTEREOSYSTEMFORiPhone®ANDiPod
Owner’sManual
®
Model Number:
Serial Number:
The KICKER iKICK iK350 Digital Stereo System for iPhone and iPod is designed for “Livin’ Loud” with your iPhone and
iPod in the home environment. The iK350 is fully featured with dual full-range 4” (`102mm) KICKER drivers and 1/2”
(13mm) Mylar tweeters driven by a powerful stereo amplifi er with digital signal processing. The 4.5” (114mm) square
passive radiator (subwoofer) on the back of the iK350 balances the sonic output, adding the punchy low-frequency
response that put KICKER subwoofers on the map. The rotary control and infrared remote allow simple, streamlined
control of your iK350 Stereo System. The iK350 can be used with any 4th generation or newer iPod. In addition, the
iK350 boasts a wide range of connectivity options including stereo RCA outputs, composite video output, and a 1/8”
stereo auxiliary input for incorporating additional audio devices with your iK350 Stereo System. Note: Third Generation
and older iPods work by connecting their headphone output to the auxiliary input on the rear of the iK350.
DOCKING YOUR iPod
1. Attach the included Adjustable Device Support to the docking bay.
2. Connect your iPod to the iK350’s dock connector.
3. Plug the power cable into the DC input on the back of the iK350.
4. Plug the 2-prong electrical plug into a surge protected electrical outlet.
The iK350 will begin to authenticate your iPod. During this time, the
“DOCK” LED will fl ash until authentication is complete. If “DOCK” continues
to fl ash after 60 seconds, authentication has failed; Disconnect and
reconnect the iPod. If problems persist, test another iPod or iPhone device,
or contact KICKER support or Apple support.
iK350
Figure 1
5. Press the rotary control knob to exit Standby mode and activate the
iK350.
PERFORMANCE
The iK350 docking station has been optimized to match the sonic output of the iPod with the iPod’s EQ in the “Off”
setting. The iPod’s “Sound Check” should also be off; otherwise you may experience poor bass response and lower
volume levels in your music.
Model: iK350
Speaker Design 2 - Way
Woofer Size, in (mm) 4 (102)
Tweeter Size, in (mm) 1/2 (13)
Tweeter Design Mylar
Passive Radiator Size, in (mm) 4.5 X 4.5 (114 X 114)
RMS Power, Watts @ 1% Total Harmonic Distortion 2 X 10
Effective Frequency Range, Hz 65-20K
Power Supply, Volts (Ampere) 12 (3)
Height, in (mm) 8 (203)
Width, in (mm) 15 (381)
Depth, in (mm) 7 (178)
Weight, lb (kg) 7.38 (3.3)
2
iK350STEREOSYSTEM
Figure 2
1/2” (13mm) Mylar
Tweeters
4” (102mm) FullRange Drivers
Figure 3
Docking Bay
LED Display
Rotary Control
Magnetic Remote Storage
Transport Handle
Passive Square
Radiator
Composite Video Output
Stereo RCA Outputs
DC Power 12 Volts
1/8” Stereo
Auxiliary Input
IMPORTANT SAFETYINSTRUCTIONS
Read and follow all the instructions listed in this manual. Follow all safety and procedural recommendations to prevent
damage to your self, your KICKER product, or your portable entertainment device.
The iK350 should not be used near water or in an environment where exposure to liquids is possible. This includes but is
not exclusive to areas where splashing, dripping, leaks, spills, and exposure to rain can occur. Liquid containers should
not be placed on or near the iK350 Stereo System. The iK350 Stereo System should not be cleaned with liquid cleaners.
Use only a dry cloth to clean the iK350. Only use the iK350 in areas with adequate open ventilation allowing at least 4”
of space on all sides of the iK350. Do not set the iK350 on any surface or cover the iK350 with any object that could
impede the airfl ow to and from the iK350 Stereo System. The iK350 should not be placed near any source of heat. This
includes but is not limited to stoves, radiators, heating elements, electronic heat sources, and areas where excessive
solar heat can be generated. Do not install the iK350 near any fl ame or place any fl ammable objects near the device.
The power outlet used to provide power to the iK350 should be accessible at all times. The polarized 2-prong electrical
plug has a wide blade and narrow blade that should fi t into the corresponding wide and narrow receiving connections
of your electrical outlet. Do not force the plug into the outlet. If the plug provided with the unit does not fi t, consult with
an electrician to upgrade the electrical outlet accordingly. The power cord should be situated in a way that protects it
from being pinched, walked on, tripped over, or accidentally pulled from the electrical outlet or the electrical input on the
iK350. Do not run the cable through doorways or underneath objects that could damage the wire or tear the insulating
material surrounding the wire. Only use the manufacturer supplied power supply with the iK350. We recommend using a
surge protector/power conditioner and unplugging the iK350 during any electrical storms or situations that could cause
voltage fl uctuations in the electrical system.
3
USING THE SYSTEM MENU ROTARY CONTROL
The iK350 Stereo System’s rotary control provides an intuitive user interface. The System Menu options listed on the
LED display below are available for adjustment by the rotary control. The rotary control knob is used as a push-button to
power on the iK350 and to scroll through the menus available on the LED display. Turning the rotary control knob allows
you to adjust the parameters of the selected menu.
Figure 4
STBY DOCK
Tap the rotary control knob
to scroll through menu
selections. Tap and hold to
turn the unit off.
After plugging the power supply into the DC input on the back of the iK350, the unit will be in “Standby” mode, as
displayed by the LED display on the System Menu. Turn the power on by pushing the rotary control button once. When
the power is on, the “DOCK” LED will be illuminated on the System Menu.
Volume: By default, the iK350 will be in volume control mode. Turn the rotary knob to adjust the volume up or down.
The rotary control will automatically revert to volume control mode after a short time period if any other menus have been
selected.
To scroll through the other menus, simply use the rotary control as a push-button. Each single button push will take you
from one menu to the next, rotating through TREB>BASS>DOCK/AUX and back to the volume control.
Treble: To adjust the treble on the iK350, use the rotary control as a push-button to scroll through the menus until the
“TREB” menu is displayed on the LED display. Turn the rotary control knob clockwise to increase treble and counterclockwise to reduce treble.
AUX
B
ASSTREB
Turn the rotary control to adjust
the System Menu parameters.
iK350 System Menu
Bass: To adjust the bass level on the iK350, use the rotary control as a push-button to scroll through the menus
until the “BASS” menu is displayed on the LED display. Turn the rotary control knob clockwise to increase bass and
counterclockwise to reduce bass.
Input Source (DOCK/AUX): To enable the auxiliary input on the iK350, an external device must be plugged into the
1/8” stereo auxiliary input on the back of the unit. Use the rotary control as a push-button to scroll through the menus
until your current input source (DOCK/AUX) is fl ashing. Turn the rotary control clockwise and counter-clockwise to switch
between AUX and DOCK input. You may also enable auxiliary input by using the Mode button on your remote control to
cycle through menus, then pressing the up/down arrows to select your input source.
Standby: In “Standby” mode, the iK350 will be powered down, but your docked iPod will continue to charge as long as
a power source is plugged into the DC input on the back of the iK350. To enter standby mode simply press and hold the
rotary control button until the unit turns off and “STBY” is illuminated.
4
iK350STEREOSYSTEM
USING THE REMOTE CONTROL
The Infrared Remote Control enables you to control your iPod and access the iK350 System Menu from a convenient
location. With the fully featured remote control it is easy to access all of your iPod’s music and/or video content.
Figure 5
iK350
Power On/Off
Mute On/Off
Change Treble, Bass and
Input Source options for
the iK350
Skip Backward
(Hold down to Rewind)
Navigate upward through the iPod menu directory or
increase values within the iK350 System Menu.
Press the up arrow while in the Input Source Menu to
enable the Aux input.
7
7
Volume Up
Volume Down
Navigate downward through the iPod menu directory or
reduce values within the iK350 System Menu.
Press the down arrow while in the Input Source Menu to
disable the Aux input.
Play/Pause
Skip Forward
(Hold down to Fast
Forward)
Make selections and enter sub-directories within the iPod.
Navigate toward iPod root directory.
CONNECTING EXTERNAL DEVICES
To connect an external video display to the iK350, make sure the video output is enabled on your iPod device. Connect
a standard RCA composite video cable from the composite video output on the back of the iK350 to the RCA video
input on your external video display. See Figure 3. This is a pass-through connection. If there are any problems with your
external video display, refer to the iPod device manual or the instructions packaged with your external video display.
To connect an external audio device to the iK350, enable Aux-In mode with the rotary or remote control as described in
the Input Source section on the previous page. Connect your line level device to the 1/8” stereo input on the back of the
iK350. See Figure 3. If the sound is distorted, you may be overdriving the auxiliary input. Try turning down the external
device until the sound is no longer distorted. Note: 1st – 3rd Generation iPods will require the use of the auxiliary input for
audio playback.
To use an external audio device for output, connect the RCA outputs on the back of the iK350 to the input(s) of your
third-party device. The audio output is at a fi xed level and not adjustable with the iK350 volume control. Use your external
audio device to attenuate the input/output level.
5
SISTEMA ESTEREOFÓNICO DIGITAL PARA
iPhone
Distribuidor autorizado KICKER:
Fecha de compra:
Número de modelo:
Número de serie:
El sistema estereofónico digital iK350 iKICK de KICKER ha sido diseñado para vivir a todo volumen Livin’ Loud® con su
iPhone y iPod en ambientes residenciales. El iK350 viene con todas las funciones, dos excitadores KICKER de gama
completa de frecuencias de 4 plg. (102 mm) y dos tweeters de domo de seda de 1/2 plg. (13 mm) energizados por
un poderoso amplifi cador estereofónico con procesamiento de señal digital. El radiador pasivo cuadrado de 4.5 plg.
(114 mm) (subwoofer), ubicado en la parte de atrás del iK350, equilibra la salida sónica y agrega la briosa respuesta de
bajas frecuencias que hizo fi gurar a los subwoofers de KICKER. El control rotatorio y el control remoto infrarrojo permiten
controlar simple y estilizadamente el sistema. El iK350 se puede utilizar con cualquier iPod y tiene una amplia gama de
opciones de conectividad, tales como salidas RCA estereofónicas y una entrada auxiliar estereofónica de 1/8 de plg.
para conectarle dispositivos de sonido adicionales.
MONTAJE DEL iPod
1. Conecte el dispositivo ajustable el apoyo a la bahía de acoplamiento.
2. Conecte el iPod al conector de la base del iK350.
3. Enchufe el cable de alimentación en la entrada de corriente continua
ubicada en la parte de atrás del iK350.
iK350
®
Y iPod® MANUAL DEL PROPIETARIO
Figura 1
4. Meta el enchufe de dos patas en un enchufe eléctrico protegido
contra sobrevoltaje.
El iK350 comenzará a autenticar su iPod. Durante este lapso, el icono
“Dock” seguirá parpadeando hasta que se complete la autenticación.
Si el icono sigue parpadeando después de 60 segundos, entonces
la autenticación ha fallado. Desconecte y vuelva a conectar el iPod. Si
persisten los problemas, pruebe con otro iPod o iPhone, o contacte al
departamento de soporte técnico de KICKER o de Apple.
5. Oprima la perilla giratoria para salir del modo Standby (En espera) y
activar el iK350.
RENIMIENTO
Modelo: iK350
Diseño de altavoz 2 canales
Tamaño de woofer, plg. (mm) 4 (102)
Tamaño de tweeter, plg. (mm) 1.5 (13)
Diseño de tweete Mylar
Tamaño del radiador pasivo, plg. (mm) 4.5 X 4.5 (114 X 114)
Potencia RMS, W a 1% de distorsión armónica total 2 X 10
Gama efectiva de frecuencias, Hz 65 – 20K
Fuente de alimentación, V (A) 12 (3)
Altura, plg. (mm) 8 (103)
Ancho, plg. (mm) 15 (381)
Fondo, plg. (mm) 7 (178)
Peso, lbs. (kg) 7.38 (3.3)
6
SISTEMAESTEREOFONICOiK350
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.