Page 1
2*
cUL Certified
for Wet Location
Universal 8" School House Fixture
2*
Kichler® Lighting
7711 East Pleasant Valley Road
P.O. Box 318010
Cleveland, Ohio 44131-8010
Customer Service
866.558.5706
8:30 AM to 5:00 PM EST,
Monday - Friday
Instruction Manual
A Kichler® Select light fixture
™
Page 2
1
1. SAFETY RULES
"CAUTION-RISK OF FIRE"
CONSULT A QUALIFIED ELECTRICIAN TO
ENSURE CORRECT BRANCH CIRCUIT
CONDUCTOR.
WARNING! RISK OF ELECTRIC SHOCK
All electrical connections must be made in
accordance with local codes, ordinances, or
national codes. If you are unfamiliar with
installing electrical wiring, secure the services
of a qualified electrician. Before starting this
installation, disconnect the power by turning
off the circuit breaker at your main panel or
removing the fuse at the fuse block. Turning
the power off using the ceiling fan switch
(speed control on/off) is not sufficient to
prevent electrical shock.
NOTE: The important safeguards and
instructions appearing in this manual are not
meant to cover all possible conditions and
situations that may occur. It must be
understood that common sense, caution and
care are factors which cannot be built into any
product. These factors must be supplied by the
person (s) caring for and operating the unit.
2. PACKAGE CONTENTS
Unpack your fan and check the contents. You
should have the following items:
a
a. Light fixture
b. Glass shade
c. 13 watt E127 compact fluorescent lamp
d
b
c
d. Part bag contents:
Nut
Spring washer
Pull chain and fob
Wire nuts (2)
Page 3
Universal 8" School House Fixture
o
-
o
-
o
-
o
-
o
-
o
-
o
-o-o-o-o-o-o
3. INSTALLING THE LIGHT KIT
2
1. Remove and discard the center plug from
the switch housing. Attach the light kit to the
switch housing by feeding the light kit wires
(black and white) through the hole in the
center of the switch housing, then screw the
light kit onto the switch housing.
Attach the nut & lock washer on the inside of
the switch housing making sure the light kit is
secure to prevent movement after installation.
(Fig. 1)
2. Locate the white and blue wires inside the
switch housing labeled FOR LIGHT.
3. Attach the wires from the light kit to the
wires inside the switch housing by pushing the
polarized connections together.
- White wire to White wire
- Blue wire to Black wire
Nut
Lock washer
Switch
housing
Center
plug
Light kit
Fig. 1
4. Raise and hold the light kit assembly close
to the mounting plate of the ceiling fan. Push
the square wire connectors together. (Fig. 2)
NOTE: The square connectors are color
coded. Match the color coded sides of each
plug and push. They will attach ONLY when
matched correctly.
5. Carefully push all wires back into the switch
housing, then install the light kit assembly onto
the mounting plate with 3 screws provided. Be
sure to tighten all screws. (Fig. 2)
Mounting plate
Square connectors
Light kit
assembly
Fig. 2
Screws
Page 4
3
4. INSTALLING THE LIGHT BULBS &
GLASS SHADE
1. Install the 13 watt E27 compact fluorescent
lamp (provided). (Fig. 3)
2. Attach the glass shade to the light fixture by
tightening each of the mounting screws
located around the outside of the fixture.
Tighten each screw evenly to center the glass
shade. DO NOT OVER TIGHTEN. (fig 3)
3. Attach a pull Chain Fob to the beaded pull
chains on the light fixture and speed chain.
4. Your installation is now complete. Restore
electrical power and enjoy your new ceiling fan
Lamp socket
Screws
light fixture.
Glass shade
Bulbs
Fig. 3
Loading...