Page 1
2*
Kichler® Lighting
7711 East Pleasant Valley Road
P.O. Box 318010
Cleveland, Ohio 44131-8010
Customer Service
866.558.5706
8:30 AM to 5:00 PM EST,
Monday - Friday
Universal Low Profile Fixture
Designed to fit 30” to 36” Sweep Fan Models
Instruction Manual
cUL Certified
for Wet Location
A Kichler
®
Select light fixture
™
2*
Page 2
1
1. SAFETY RULES
"CAUTION-RISK OF FIRE"
CONSULT A QUALIFIED ELECTRICIAN TO
ENSURE CORRECT BRANCH CIRCUIT
CONDUCTOR.
Special Notice: This appliance is equipped
with a "Wattage Limiting Device" required by
the United States Department of Energy. The
device has been installed at the factory and
can not be removed.
Installing Lamps in excess of 190 total watts
will disable the units light fixture. If this should
happen, you will need to reset the lighting
fixture by turning the power off to the ceiling
fan and/or light fixture, reinstalling lamps
totaling less that 190 watts and then turning
the power back on.
WARNING! RISK OF ELECTRIC SHOCK
All electrical connections must be made in
accordance with local codes, ordinances, or
national codes. If you are unfamiliar with
installing electrical wiring, secure the services
of a qualified electrician. Before starting this
installation, disconnect the power by turning
off the circuit breaker at your main panel or
removing the fuse at the fuse block. Turning
the power off using the ceiling fan switch
(speed control on/off) is not sufficient to
prevent electrical shock.
NOTE: The important safeguards and
instructions appearing in this manual are not
meant to cover all possible conditions and
situations that may occur. It must be
understood that common sense, caution and
care are factors which cannot be built into any
product. These factors must be supplied by the
person (s) caring for and operating the unit.
2. PACKAGE CONTENTS
a
b
c
d
Unpack your fan and check the contents. You
should have the following items:
a. Light fixture
b. Glass shade
c. 2, 50W, E-11 JD TYPE, halogen lamps
d. Part bag contents:
Nut
Spring washer
Pull chain and fob
wire nuts (2)
Page 3
Universal Low Profile Fixture
3. INSTALLING THE LIGHT KIT
1. Remove and discard the center plug from
the switch housing. Attach the light kit to the
switch housing by feeding the light kit wires
(black and white) through the hole in the
center of the switch housing, then screw the
light kit onto the switch housing.
Attach the nut & lock washer on the inside of
the switch housing making sure the light kit is
secure to prevent movement after installation.
(Fig. 1)
2
Nut
Lock washer
Switch
housing
Center
plug
Light kit
2. Locate the white and blue wires inside the
switch housing labeled FOR LIGHT.
3. Attach the wires from the light kit to the
wires inside the switch housing by pushing the
polarized connections together.
- White wire to White wire
- Blue wire to Black wire
4. Raise and hold the light kit assembly close
to the mounting plate of the ceiling fan. Push
the square wire connectors together. (Fig. 2)
NOTE: The square connectors are color
coded. Match the color coded sides of each
plug and push. They will attach ONLY when
matched correctly.
5. Carefully push all wires back into the switch
housing, then install the light kit assembly onto
the mounting plate with 3 screws provided. Be
sure to tighten all screws. (Fig. 2)
Fig. 1
Mounting plate
Square connectors
Screws
Light kit
assembly
Fig. 2
Page 4
3
4. INSTALLING THE LIGHT BULBS &
GLASS SHADE
1. Install both of the 50 watt, E-11 JD TYPE,
halogen lamps (provided), one in each fixture
socket. (Fig. 3)
2. Attach the glass shade to the light fixture by
turning the glass shade clockwise. DO NOT
OVER TIGHTEN. (Fig. 3)
3. Attach a pull Chain Fob to the beaded pull
chains on the light fixture and speed chain.
4. Your installation is now complete. Restore
electrical power and enjoy your new ceiling fan
light fixture.
Lamps
Lamp socket
Glass shade
Fig. 3
Loading...