Page 1
2*
2*
Brinbourne™ 3 Light Fixture
Kichler® Lighting
7711 East Pleasant Valley Road
P.O. Box 318010
Cleveland, Ohio 44131-8010
Customer Service
866.558.5706
8:30 AM to 5:00 PM EST,
Monday - Friday
Designed to coordinate with a popular Kichler® ceiling fan
Instruction Manual
A Kichler® Decor light fixture
™
Page 2
1
1. SAFETY RULES
"CAUTION-RISK OF FIRE"
CONSULT A QUALIFIED ELECTRICIAN TO
ENSURE CORRECT BRANCH CIRCUIT
CONDUCTOR.
Special Notice: This appliance is equipped
with a "Wattage Limiting Device" required by
the United States Department of Energy. The
device has been installed at the factory and
can not be removed.
Installing Lamps in excess of 190 total watts
will disable the units light fixture. If this should
happen, you will need to reset the lighting
fixture by turning the power off to the ceiling
fan and/or light fixture, reinstalling lamps
totaling less that 190 watts and then turning
the power back on.
WARNING! RISK OF ELECTRIC SHOCK
All electrical connections must be made in
accordance with local codes, ordinances, or
national codes. If you are unfamiliar with
installing electrical wiring, secure the services
of a qualified electrician. Before starting this
installation, disconnect the power by turning
off the circuit breaker at your main panel or
removing the fuse at the fuse block. Turning
the power off using the ceiling fan switch
(speed control on/off) is not sufficient to
prevent electrical shock.
NOTE: The important safeguards and
instructions appearing in this manual are not
meant to cover all possible conditions and
situations that may occur. It must be
understood that common sense, caution and
care are factors which cannot be built into any
product. These factors must be supplied by the
person (s) caring for and operating the unit.
2. PACKAGE CONTENTS
Unpack your light fixture and check the
a
b
c
d
e
contents. You should have the following items:
a. Light Fixture
b. Glass Shade Retainer Nuts (3) (Pre-
installed on the Light Fixture Sockets)
c. Glass Shades (3)
d. 3, 40 Watt E-12 Candelabra Lamps
e. Part bag contents:
Nut
Spring Washer
Wire Nuts (2)
Light Socket Retainer Nut Wrench
Page 3
Brinbourne™ 3 Light Fixture
3. REMOVING THE DECORATIVE CAP
Step 1. Remove the Plug and Decorative Cap
from the ceiling fan by unscrewing the Plug.
(see figure 1)
Step 2. Remove the Mounting Plate by
removing two of the three screws around the
outside edge of the plate and loosing the third.
Rotate the mounting plate so the remaining
screw heads are in the large end of the
keyhole slots and remove the plate. (see
figure 1)
2
4. INSTALLING THE LIGHT FIXTURE
NOTE: This ceiling fan light fixture is
specifically designed to fit the Kichler®
Brinbourne™ Ceiling Fan 300262. It will not fit
or work with ANY OTHER ceiling fan.
1. Attached the new mounting plate by placing
the keyholes over the two screw heads
previously loosened, rotate the mounting plate
so the screw heads are at the narrow end of
the keyholes. Replace the third screw and
tighten all three screws. (see figure 2).
Mounting plate
Decorative cap
Bottom housing
Screws
Plug
Fig. 1
Mounting plate
cover
Bottom housing
Screws
Fig. 2
Page 4
3
Mounting plate
cover
Wire connectors
Screws
2. Raise and hold the light fixture assembly
close to the mounting plate cover. Attach the
wires from the light fixture to the wires from the
fan by pushing the polarized connections
together.
- White wire to White wire
- Black wire to Blue wire
3. Carefully push all the wires back into the
mounting plate.
Attach the light fixture assembly to the
mounting plate by aligning the screw holes (3)
around the outside edge of the light fixture
mount plate with the holes on the fan mounting
plate. Insert all three screws and tighten.
Light fixture
Socket nut wrench
Fig. 3
Glass shades
Glass shade retainer nuts
5. INSTALLING THE LAMPS & GLASS
SHADES
1. Remove the glass shade retainer nut from
each socket. Place a glass shade over the
socket and replace the retainer nut. Do Not
over tighten but make sure the retainer nut is
secure and snug.
NOTE: A Socket Nut Wrench has been
provided to help in this installation.
2. Install 3, 40 Watt E-12 candelabra lamps
(included). (Fig. 4)
Fig. 4
Lamps
3. Your installation is now complete. Restore
electrical power and enjoy your new ceiling fan
light fixture.
Loading...