Page 1
1
REMOTE CONTROL INSTALLATION
NOTE:
When installing the remote control, be sure your fan is operated in
"HIGH SPEED" and light is in "ON" condition at the switch knob.
GENERAL INFORMATION
337001
ON
This remote control is designed to separately control your ceiling fan speed
and light brightness.
The fan button will control the fan speed. (Hi, Med., Low, Off)
The light buttons will control the lights, brightness dimmer and off.
The red indicator on the transmitter will light when the button is pressed.
INST ALLA TION AND OPERA TING
INSTRUCTIONS
NOTE: This remote control unit is equipped with 16 frequency code
combinations to prevent possible interference from or to other remote units.
The frequency switches on your receiver and transmitter have been preset at
the factory. Please recheck to make sure the switches on transmitter and
receiver are set to the same position, any combination of settings will
operate the fan as long as the transmitter and receiver are set to the same
position.
1. SETTING THE FREQUENCY CODE
To set the frequency (code), follow these steps
Caution! The dip switches on the receiving unit are covered with a rubber
cover, remove the rubber cover and then have it replaced after making any
changes to the dip switches.
A. Setting the code on the transmitter:
a. Remove the battery cover. Press firmly below the arrow and slide
battery cover off.
b. Slide the code switches to your choice of up or down position. (Factory
setting is all up). Use a small screwdriver or a ballpoint pen to slide each
small switch UP or DOWN. (Fig. A)
c. Replace the battery cover on the transmitter.
B. To set the code on the receiver, slide each code switch to the same position
as set on your transmitter. (Fig. B)
Code switches
Transmitter
Fig. A
ON
Code switches
Receiver
Fig. B
RECEIVER
2. INSTALLING THE RECEIVER UNIT
A. Safety precautions:
WARNING: HIGH VOLTAGE! Household electrical power can
cause serious injury or death. Disconnect the source of electrical power
to the ceiling fan by removing the fuse or switching off the circuit
breaker.
B. Installing the receiver unit.
a. Remove the ceiling fan canopy from the mounting bracket.
b. Disconnect the existing wiring between the ceiling fan and supply at
the electrical junction box.
c. Lay the black antenna wire on top of the receiver and slide the
receiver into the mounting bracket as shown in Figure C. Do NOT
let the antenna wire get tangled up in the other electrical wires.
d. Make the connections as follows, using the wire nuts supplied: (Fig. D)
CONNECT TO
Green fan wire...........................................Bare supply wire
Black receiver wire (AC IN L)..................Black supply wire
White receiver wire(AC IN N)..................White supply wire
White receiver wire (TO MOTOR N).......White fan wire
Black receiver wire (TO MOTOR L)........Black fan wire
Blue receiver wire(FOR LIGHT)..............Blue light wire
AC SUPPLY
BLACK
WHITE
RECEIVER
BLUE BLUE
BLACK
WHITE
BARE GREEN
Fig. C
BLACK
WHITE
Fig. D
Page 2
If any of the fan or supply wires are a different color, have this unit
installed by a qualified electrician.
e. Push all connected wires up into junction box.
f.
Reinstall the canopy on the mounting bracket.
g. Restore the electrical power.
3. OPERATING TRANSMITTER:
2
Fig. E
A. Install 1 x
remove the battery if not used for long periods. (Figure E)
B. Store the transmitter away from excess heat or humidity.
C. This remote control unit is equipped with 16 frequency code
combinations to prevent possible interference from or to other remote
units such as garage door openers, car alarm or security system. If you
find that your fan and light kit go on and off without using your remote
control, simply change the combination code in your transmitter and
receiver.
D. Operation buttons on the panel of the transmitter: (Figure F)
The " HI, MED, LOW" buttons:
These three buttons are used to set the fan speed as follows:
LOW= Low speed MED= Medium speed HI= High speed
The "OFF" button:
This button turns the fan MOTOR off.
The" " button:
This button controls the light brightness and will turn the light on or off.
The light function is controlled by pressing the " " key. Hold the key
down to increase or decrease the light. Tap the key quickly to turn the
light off or on. If you press the button in excess of 0.7 seconds it
becomes a dimmer. The light varies cyclically in 0.8 seconds. The light
key has auto resume, so it will stay at the same brightness as the last
time it was turned off.
YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND
LIGHT.
9V
battery (included). To prevent damage to transmitter,
Fig. F
4. TROUBLESHOOTING GUIDE
If the Ceiling Fan and or light fixture(s) fail to respond to commands
from the transmitter, check the following.
● Check the main power supply and reset or turn on the breaker.
● Make sure the "Receiver Unit" is wired properly.
● Light Fixture pull chain switch turned to ON ?
● Make sure the speed pull chain is set to the HIGHEST speed.
● Good batteries in transmitter ? Replace if needed.
● Transmitter and Receiver "frequency" switches set to match each other ?
NOTE: The distance between the transmitter and receiver should not be
greater than 30 feet. For best performance, make sure the Black
Antenna on the end of the receiver unit remains extended and not
tangled with any of the electrical wires.
WARNING: This control system is intended for use on 120 volt / 60Hz
power systems ONLY.
WARNING: The dimming function on this control system is NOT intended
for use with NON-Dimmable Fluorescent lamps.
Loading...